M2 Antenna Systems 432-15WL Guía de inicio rápido

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

Rev.00

Model .........................................432-15WL

Frequency Range.......................430 To 436 MHz

*Gain ..........................................21.5 dBi

Front to back ..............................22 dB Typical

Beamwidth ...............................E=15° H=16°

Feed type ...................................Folded Dipole

Feed Impedance........................50 Ohms Unbalanced

Maximum VSWR........................1.2:1 Typical

Input Connector..........................“N” Female

Power Handling..........................1 kW

Boom Length / Dia......................416” / 1.5,1.25,1.0 &.75”

Maximum Element Length..........13-5/8”

Turning Radius:..........................19’

Stacking Distance.......................96” High & 96” Wide

Mast Size....................................1-1/2” to 2” Nom.

Wind area / Survival...................2.8 Sq. Ft. / 100 MPH

Weight / Ship Wt.........................13Lbs. / 14 Lbs.

M2 Antenna Systems, Inc.

Model No: 432-15WL

FEATURES:

The 432-15WL uses the 432-23WLA as it’s starting point. This allows ‘13WLA owners to easily upgrade to the

new ‘15WL by changing the element set and adding a new boom tip section . The 432-15WL produces over 25.3 dBd

gain in a four Yagi array, its also an excellent stand alone antenna with flatter match and broader bandwidth..

The driven element is a modified and adjustable folded dipole. Its heart is a unique machined aluminum Driven Element

Module. All three connectors on the module are threaded in and feature 'O' ring seals. Internal connections are encapsu-

lated in a space age silicone gel with nearly 4 times the dielectric strength of air. Each parasitic element is a solid 3/16"

rod, mounted through the boom on a UV stabilized, black polyethylene button insulator and locked in place with stainless

steel shaft retainers.

The 432-15WL is available as an ADD ON KIT or as a new standalone antenna. It has been designed for outstanding

performance and long term electrical and mechanical integrity.

SPECIFICATIONS:

*Subtract 2.14 from dBi for dBd

432-15WL UPGRADE MANUAL

New Installation

1. Follow the 432-13WL assembly manual instructions, but do not use BOOM SECTION #7(3/4” X .049 X 27”)

& 3/16” ELEMENT SET. Instead, use BOOM SECTION #7 (3/4” X .049 X 60” SOE), BOOM SECTION #8

(3/4” X .049 X 21”) & 3/16” ELEMENT SET supplied with the 432-15WL upgrade kit. (SEE PICTURE #1 & #2).

2. Trim Driven Element Rod to = 5-3/16” & adjust Shorting Bar dimension. (SEE PICTURE #3).

Existing 432-13WL Upgrade

1. Remove all elements. Note: retainers will no longer be usable. We have supplied new ones in the hardware

upgrade kit. Please save button insulators, these will be re-used.

2. Remove BOOM SECTION #7 (3/4” X .049 X 27”). Replace with new 432-15WL UPGRADE BOOM SEC-

TION #7 (3/4” X .049 X 60” SOE) supplied in 432-15WL upgrade kit.

(SEE PICTURE #1 & #2).

3. Install BOOM SECTION #8 (3/4” X .049 X 21”) supplied in 432-15WL upgrade kit.

(SEE PICTURE #1 & #2).

4. Install new 3/16” element set. (SEE DIMENSION SHEET). We have supplied in upgrade hardware kit, new

retainers & extra buttons.

5. Trim Driven Element Rods to = 5-3/16” & adjust Shorting Bars (SEE PICTURE #3).

3/16” Element Rod Installation Reminders

1. Lay out the elements by length and position as shown the DIMENSION sheet. Start with the reflector ele-

ment and push on a black button insulator to about 1/2” from center. Insert the element through the holes

1/2" from the rear of the boom and install the second button, snugging it up into boom. DO NOT BOTHER

WITH ACCURATELY CENTERING the element at this time and DO NOT INSTALL the stainless steel in-

ternal locking SHAFT RETAINERS yet. This is easier to do after all the elements are installed in the boom.

2. Install the 3/16” DRIVEN ELEMENT as you did the reflector. Then continue with the installation of the DI-

RECTORS. Note that the Director Elements do not consistently diminish in length from rear to front, so pay

close attention to length and position.

3. Now center the elements. Use a tape measure to EQUALIZE the element length on each side of the boom.

Once you have all the elements centered, sight down the element tips from the rear comparing each side.

Look for any obvious discrepancies and correct if found.

4. NOTE: The SHAFT RETAINERS should always be used for permanent and long term antenna installa-

tions. For portable or temporary use, or whenever it is anticipated that the antenna will be disassembled

within a short time, the retainers may be left off. The button insulators, alone, hold the elements quite se-

curely.

The SHAFT RETAINERS are installed on both sides of each element rod, butted on the button insulators.

To start the retainers, use thumb and index finger to hold one over end of the 3/8 x 3” push tube, retainer

dished into tube. Hold the element firmly and start the retainer onto the rod by applying pressure with the

push tube. Push the retainer until up tight against the button insulator (Locking pliers, lightly clamped up

against opposite button insulator will help maintain center reference and keep you from pushing the first

retainer too far). Repeat for the opposite side. Continue installing retainers until all elements are locked in

place.

432-15WL UPGRADE ASSEMBLY

4-3/4”

5-3/16” NOTE:

ONE SIDE OF DRIVEN

ELEMENT SHOWN.

APPLY DIMS TO

BOTH SIDES.

432-15WL OVERHEAD SUPPORT

432-15WL DIMENSION SHEET

TOOLS REQUIRED: Screwdriver, 11/32 wrench, socket or spintite, a 7/16" and 1/2" wrench or socket, tape measure.

432-15WL PARTS & HARDWARE

DESCRIPTION......................................................................................... QTY

BOOM SECTION #7: 3/4” X .049 X 60” SOE........................................... 1

BOOM SECTION #8: 3/4” X .049 X 21“ ...................................................1

ELEMENT RODS, 3/16 X SEE DRAWING.............................................. 42

KEVLAR, .075 X 11’................................................................................1

HARDWARE:

BUTTON INSULATORS...........................................................................10

SHAFT RETAINERS................................................................................ 85

PUSH TUBE, 3/8” X 3”............................................................................. 1

SCREW, 8-32 X 1.0”, SS .........................................................................2

LOCKNUT, 8-32, SS................................................................................2

M2ANTENNA SYSTEMS, INC.

4402 N. SELLAND AVE.

FRESNO, CA 93722

(559) 432-8873 FAX: 432-3059

www.m2inc.com Email: [email protected]

Tabla de contenidos

Otros manuales de Antena de M2 Antenna Systems

M2 Antenna Systems

M2 Antenna Systems 348CP18 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 44.5-5 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 137CP14HD Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 440-6SX Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 6-30LP11 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 440-18 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 20M5-125 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 222XP30 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 25M4 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 6M3 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems FGSD-2.4DH Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 20M4DX Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 35.7-4 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 500-1000-10 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 40M1L Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 248CP22A Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 303CP26 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 403CP20 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 48.5-4 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 6M5XHP Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 902-14WLC Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 40M2C Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 222-10EZ Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 222 HO LOOP Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario