M-system R80YVT4N Manual de usuario

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7033 P. 1 / 6

INSTRUCTION MANUAL

DC VOLTAGE OUTPUT MODULE, 4 points

(4 points, non-isolated, tension clamp terminal block) MODEL

R80YVT4N

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

DC voltage output module..................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■GENERAL PRECAUTIONS

• Before you remove or mount the unit, turn off the power

supply and output signal for safety.

• DO NOT set the switches while the power is supplied.

The switches are used only for maintenance without the

power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 10 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■POWER UP

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for-

satisfying complete performance described in the data-

sheet.

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

Confirm that the locking clamps of the extension power supply module

are set. Insert the module in parallel to the next one while aligning the

grooves of both modules (A & B in the above figure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

R80YVT4N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7033 P. 2 / 6

• Protective Cover

The protective cover is to be attached over the connected I/O module

at the right end.

Align the hooks on the cover with the grooves of the module and slide it

straight until the hooks are latched.

When removing the cover, pull it out while squeezing the hooks inward.

Groove

Hook

■HOW TO UNMOUNT THE MODULE FROM DIN RAIL

Release the locking clamps and pull out straight the module.

Caution !

1)Be careful not to hurt your hand by pointed edges of the internal bus

connector.

2) I/O modules cannot hold tightly on the DIN rail by themselves without

power/network module.

Secure them to the position if necessary by using DIN rail end plates.

• Removing an intermediate module

R80YVT4N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7033 P. 3 / 6

COMPONENT IDENTIFICATION

■LEFT VIEW

Terminal

DIP SW

Term

SW2

■FRONT VIEW ■RIGHT VIEW

Internal Bus

Connector

Module Address

DIP SW

SW1

Status Indicator LED

Output Status

Indicator LEDs

Output Connector

RUN

■STATUS INDICATOR LED / OUTPUT STATUS INDICATOR LED

LED OPERATION COLOR FUNCTION

RUN

Indicator LED

ON Red Upper communication: Stopping or abnormal

Internal communication: Abnormal

ON Green Upper communication: Normal

Internal communication: Normal

Blink

1 sec. sycle

– Output value error

(Exceeds the upper limit of setting range).

Blink

400 msec. cycle

– Output circuit abnormality (AD converter response failure)

OFF – Upper communication: Stopping or abnormal

Internal communication: Normal

Output Status

Indicator LED

OFF Red Output data in the range

ON Output value error

(Exceeds the upper limit of setting range).

Output circuit abnormality (AD converter response failure)

R80YVT4N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7033 P. 4 / 6

■OPERATION MODE SETTING

(*) factory default setting

Note) Be sure to unused SW1-5 through 1-8 to OFF.

• Module Address Setting

Conﬁgurate the mosule address with DIP Switch.

0 - 15 are available for module address.

MODULE AD-

DRESS

SW1

1234

0(*) OFF OFF OFF OFF

1 ON OFF OFF OFF

2 OFF ON OFF OFF

3 ON ON OFF OFF

4 OFF OFF ON OFF

5 ON OFF ON OFF

6 OFF ON ON OFF

7 ON ON ON OFF

8 OFF OFF OFF ON

9 ON OFF OFF ON

10 OFF ON OFF ON

11 ON ON OFF ON

12 OFF OFF ON ON

13 ON OFF ON ON

14 OFF ON ON ON

15 ON ON ON ON

• Terminator Setting

Terminator SW2

Disabled (*) OFF

Enabled ON

■OUTPUT CONNECTOR TERMINAL ASSIGNMENT

PIN NO. ID FUNCTION

1 Ao1+ Output 1 (+)

2 Ao1- Output 1 (-)

3 Ao2+ Output 2 (+)

4 Ao2- Output 2 (-)

5 Ao3+ Output 3 (+)

6 Ao3- Output 3 (-)

7 Ao4+ Output 4 (+)

8 Ao4- Output 4 (-)

R80YVT4N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7033 P. 5 / 6

PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgurator Software (model: R80CFG)

Refer to the users manual for the R80CFG for detailed operation of the software program.

■CHANNEL INDIVIDUAL SETTING

ITEM SETTING RANGE DEFAULT VALUE

Unused setting CH enabled

CH disabled

CH enabled

Zero ﬁne adj. -320.00 - +320.00 (%) 0.00 (%)

Gain ﬁne adj. -3.2000 - +3.2000 1.0000

Zero base -10.00 - +10.00 -10.00

Full base -10.00 - +10.00 10.00

Zero scaling -32,000 - +32,000 0

Full scaling -32,000 - +32,000 10,000

Output range at communication failure or power up -5.00 - +105.00 0.00

*1. For details, refer to the users manual of R80CFG

■CHANNEL BATCH SETTING

ITEM SETTING RANGE DEFAULT VALUE

Version no. – –

Simulate output Normal output

Simulated data

Normal output

Output at the loss of communication Hold the output data

User set data output

Hold the output data

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit : mm [inch]

115 [4.53]

6 [.24]

7 [.28]

6 [.24] 7 [.28]

DIN rail

(35mm wide)

(3 [.12]) (4 [.16])

24 [.94] 72 [2.83]

55 [2.17]

R80YVT4N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7033 P. 6 / 6

■CONNECTION DIAGRAM

OUTPUT 1

BUS CONNECTOR

INTERNAL BUS

INTERNAL POWER

EXC. SUPPLY

OUTPUT CONNECTOR

–

OUTPUT 2

–

OUTPUT 3

–

OUTPUT 4

–

WIRING INSTRUCTIONS

■Tension clamp terminal block

Unit side connector: MC1,5/8-GF-3,5 (Phoenix Contact)

Applicable connector: FMC1,5/8-STF-3,5

(Phoenix Contact)

Applicable wire size: 0.2 − 1.5 mm2

Stripped length: 10 mm

Recommended solderless terminal

• AI0,25−10YE 0.25 mm2(Phoenix Contact)

• AI0,34−10TQ 0.34 mm2(Phoenix Contact)

• AI0,5−10WH 0.5 mm2(Phoenix Contact)

• AI0,75−10GY 0.75 mm2(Phoenix Contact)

• A1−10 1.0 mm2(Phoenix Contact)

• A1,5−10 1.5 mm2(Phoenix Contact)

Tabla de contenidos

Otros manuales de Sistema de E/S de M-system

M-system

M-system R30YN16C Manual de usuario

M-system

M-system R7C-EA16 Manual de usuario

M-system

M-system R7C-CT4E Manual de usuario

M-system

M-system R3-CT8A Manual de usuario

M-system

M-system R30NCIE1 Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R7E-YV2 Manual de usuario

M-system

M-system R7D-YS2A Manual de usuario

M-system

M-system M5SN Manual de usuario

M-system

M-system R7F4DC-DAC16D-H Manual de usuario

M-system

M-system R80UST4 Manual de usuario

M-system

M-system R3-SV4 Manual de usuario

M-system

M-system R7ML-EA8 Manual de usuario

M-system

M-system R5 Series Manual de usuario

M-system

M-system R7F4HC-DC32A-K Manual de usuario

M-system

M-system R7D-YV2 Manual de usuario

M-system

M-system R7F4HC-DA32-K Manual de usuario

M-system

M-system R7M-DA16F Manual de usuario

M-system

M-system R3-MS4 Manual de usuario

M-system

M-system R80DCT16A2 Manual de usuario

M-system

M-system R3Y-DA16B Manual de usuario

M-system

M-system R7K4DH-1-DAC32A Manual de usuario

M-system

M-system R7ML-LC2-R Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario