M-system R3-PA8 Manual de usuario

R3-PA8

P. 1 / 3EM-8457

TOTALIZED PULSE INPUT MODULE

(Pi 8 points, 32 Bits) MODEL R3-PA8

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■ PACKAGE INCLUDES:

Totalized pulse input module....................................... (1)

■ MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■ CONFORMITY WITH EC DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices and connected wires may

affect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure CE conformity.

■ HOT INSERTION/REMOVAL OF MODULES

Removing or replacing modules does not affect other mod-

ules on the same backplane. It is possible to replace them

without removing the power supply. However, replacing

multiple modules at once may greatly change line voltage

levels. We recommend that you replace them one by one.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing with sufﬁcient ven-

tilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output)

close to noise sources (relay drive cable, high frequency

line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■ AND ....

The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for sat-

isfying complete performance described in the data sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3-PA8

P. 2 / 3EM-8457

The bits indicating the channels to reset counter are allocated in the ﬁrst word from host PC/PLC.

When these bits are changed from 0 to 1, the counter is reset. When it is conﬁrmed that the counter is reset, return to 0.

Notice that if the bit remains at 1, the next reset will not work.

Count reset CH.1

Unused

Count reset CH.2

Count reset CH.3

Count reset CH.4

Count reset CH.8

BIT ALLOCATION OF THE FIRST WORD FROM HOST PC/PLC

COMPONENT IDENTIFICATION

RUN LED

ERR LED

Status Indicator LED

■ FRONT VIEW ■ SIDE VIEW

SW3

1Count

Reset

Count

Reset Input

Set the Count Reset SW to OFF to start counting.

Functions

■ STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with the excitation abnormality;

Green in normal operating conditions.

Input status indicator: Red LED;

1 to 8: Turns on with the inputs supplied.

9 to 15: Unused*

16: Turns on with the reset input supplied.

*The LEDs are connected with terminals via internal cir-

cuit. Therefore, the LED turns on, if the corresponding ter-

minal is connected to terminal 10 or 20. However, it does

not affect the operation.

R3-PA8

P. 3 / 3EM-8457

WIRING INSTRUCTIONS

■ SOLDERLESS TERMINAL mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt. Applicable

wire size: 0.3 – 0.5 mm2

3.2 (.13) dia.

4 min.

(.16)

12 (.47) max.

6 max.

(.24)

3 (.12) max.

130 (5.12)

27.5 (1.08) 109 (4.29) POSITIONING

GUIDE

TERMINAL

COVER

20–M3

SCREW

6.2

(.24)

Pi 1

Pi 2

Pi 3

Pi 4

Pi 5

Pi 6

Pi 7

Pi 8

COM(

Pi 1

Pi 2

Pi 3

Pi 4

Pi 5

Pi 6

Pi 7

Pi 8

� R3-PA8x/A

� R3-PA8x

+24V

INTERNAL

POWER

BUS A

BUS B

BUS CONNECTOR

Numbers in italic indicate LED No.s assigned to

the front panel LEDs.

*For dual redundant communication.

**DO NOT use the terminals No. 9, 11 through 17 and 19.

Count

Reset

Count

Reset

****

■ DIMENSIONS mm (inch)

■ CONNECTION DIAGRAM

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive

remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this

warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original

sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]

Otros manuales de Unidad de control de M-system

M-system

M-system R7ML-DC16B Manual de usuario

M-system

M-system R8-DC4C Manual de usuario

M-system

M-system R7L-SV4-R Manual de usuario

M-system

M-system R3-RR8 Manual de usuario

M-system

M-system R7C-DC16B Manual de usuario

M-system

M-system R7ML-DC16A Manual de usuario

M-system

M-system R3-NF2 Manual de usuario

M-system

M-system R3-RS8 Manual de usuario

M-system

M-system R7M-RS4 Manual de usuario

M-system

M-system R7M-YS2 Manual de usuario

M-system

M-system R30SV2 Manual de usuario

M-system

M-system R7M-SV4 Manual de usuario

M-system

M-system R7D-EC16B Manual de usuario

M-system

M-system R3-AR4 Manual de usuario

M-system

M-system R7M-EA16 Manual de usuario

M-system

M-system R3-PS3 Manual de usuario

M-system

M-system R7C-EC16B/UL Manual de usuario

M-system

M-system R7HL-DC16A Manual de usuario

M-system

M-system R7L-EC16B Manual de usuario

M-system

M-system R7HL-DC16B-R Manual de usuario

M-system

M-system R3-NEIP1 Manual de usuario

M-system

M-system R7C-EA8 Manual de usuario

M-system

M-system R7L-YV2 Manual de usuario

M-system

M-system R3-PA4A Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario