M-system R3-PA4A Manual de usuario

R3-PA4A

P. 1 / 3 EM-8387 Rev.2

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

the contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Office or representatives.

■ PACKAGE INCLUDES:

Totalized pulse input module ..................................... (1)

■ MODEL NO.

Check that model No. described on the specification label is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, including installation, connection and basic

maintenance procedures.

INSTRUCTION MANUAL

MODEL R3-PA4A

HIGH SPEED TOTALIZED PULSE INPUT MODULE

(4 points, isolated)

POINTS OF CAUTION

■ HOT INSERTION/REMOVAL OF MODULES

Removing or replacing modules does not affect other modules

on the same backplane. It is possible to replace them without

removing the power supply. However, replacing multiple

modules at once may greatly change line voltage levels. We

recommend that you replace them one by one.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing with sufficient ventila-

tion.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH in

order to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

■ AND ....

• The unit is designed to function as soon as power is

supplied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3-PA4A

P. 2 / 3 EM-8387 Rev.2

COMPONENT IDENTIFICATION

■ DIMENSIONS mm (inch)

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

130 (5.12)

27.5 (1.08) 109 (4.29) POSITIONING

GUIDE

TERMINAL

COVER

20–M3

SCREW

6.2

(.24)

SW1SW2

SW3

■FRONT VIEW ■SIDE VIEW

ERR LED

RUN LED

Gain

Count Reset

Set the Count Reset SW to OFF to start counting.

■SIDE DIP SW

•Gain: SW3

SW GAIN INPUT

1 (*)2

SW3-1 OFF ON Input 1

SW3-2 OFF ON Input 2

SW3-3 OFF ON Input 3

SW3-4 OFF ON Input 4

(*) Factory setting

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with the excitation abnormality;

Green in normal operating conditions.

R3-PA4A

P. 3 / 3 EM-8387 Rev.2

■ CONNECTION DIAGRAM

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,

under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To

submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]

WIRING INSTRUCTIONS

■SOLDERLESS TERMINAL mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solderless

terminals with insulation sleeve do not fit. Applicable wire

size: 0.3 – 0.75 mm2

3.2 (.13) dia.

4 min.

(.16)

12 (.47) max.

6 max.

(.24)

3 (.12) max.

EXC +

INP TERM. 1

INP TERM. 2

INP TERM. 3

COM

INTERNAL POWER

BUS A

BUS B*

*For dual redundant communication.

BUS CONNECTOR

Input 1

EXC +

INP TERM. 1

INP TERM. 2

INP TERM. 3

COM

Input 2

EXC +

INP TERM. 1

INP TERM. 2

INP TERM. 3

COM

Input 3

EXC +

INP TERM. 1

INP TERM. 2

INP TERM. 3

COM

Input 4

■Input Connection Example (Input 1)

• Open Collector

12VDC

20kΩ

1kΩ7.5kΩ

Otros manuales de Unidad de control de M-system

M-system

M-system R7C-RR4 Manual de usuario

M-system

M-system M8CD1 Manual de usuario

M-system

M-system R3-PT4 Manual de usuario

M-system

M-system R7D-MS4 Manual de usuario

M-system

M-system R7ML-EC16B Manual de usuario

M-system

M-system R3S-DC8 Manual de usuario

M-system

M-system R3-PA2 Manual de usuario

M-system

M-system R3Y-SV16 Manual de usuario

M-system

M-system R3Y-DS8N Manual de usuario

M-system

M-system R7L-EC8B Manual de usuario

M-system

M-system R7L-RS4 Manual de usuario

M-system

M-system R7L-EC8A Manual de usuario

M-system

M-system R7L-DA16 Manual de usuario

M-system

M-system R7D-EA16 Manual de usuario

M-system

M-system R3-SV8B Manual de usuario

M-system

M-system R7HL-DC16A Manual de usuario

M-system

M-system R3-CT4A Manual de usuario

M-system

M-system R5-NE1 Manual de usuario

M-system

M-system R8-NC3 Manual de usuario

M-system

M-system M6DXF1 Manual de usuario

M-system

M-system Mini-M M2DL Manual de usuario

M-system

M-system R7C-EC8A Manual de usuario

M-system

M-system Mini-M M2MNV Manual de usuario

M-system

M-system LONWORKS R3-NL2 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario