Lutron Electronics DFCSJ-OEM-OCC Manual de usuario

Lutron Electronics Co., Inc. 7200 Suter Road

Coopersburg, PA 18036-1299 USA

Release Wires from Connectors

Press connector buttons while pushing the wires slightly inward. Pull wires outward to release the wires from the

connectors. Do NOT pull out the wires without using the connector buttons, as damage to the product

can occur.

Packaging

Fixture packaging must protect the installed wireless fixture control so that it does not get damaged in shipping.

Customer Assistance | 1.844.LUTRON1 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com

Part of the Vive Family

Clear Connect Wireless Fixture

Controllers

Required Components

For each ﬁxture, you will need:

Clear Connect Wireless Fixture

Controller (with Occupancy Sensor)

(DFCSJ-OEM-OCC)

Clear Connect Wireless Fixture

Controller (RF Only)

(DFCSJ-OEM-RF)

Start Here

English

Important Notes:

• Forinstallationbyaqualiedxturemanufacturer.

• Usecopperconductorsonly.

• Checktoseethatthedevicetypeandratingissuitablefortheapplication.

•DO NOTinstallifproducthasanyvisibledamage.

• Ifmoistureorcondensationisevident,allowtheproducttodrycompletely

before installation.

• Operatebetween32°Fand131°F(0°Cand55°C),ambient.

• 0%to90%humidity,non-condensing.

• Forindooruseonly.

• Sensorshouldbemountedtoxtureinorientationthatmakesitparallelto

theoorwhenxtureisinstalledinceiling.

DFCSJ-OEM-OCC Clear Connect Wireless

Fixture Controller (with Occupancy Sensor)

DFCSJ-OEM-RF Clear Connect

Wireless Fixture Controller (RF Only)

InstallClearConnectWirelessFixtureController

• Ensureknockoutandadjacentsurfacesarefreefromburrs,oil,chemicals,debris,etc.

• DonotpushonthePIRlensorbuttontoinstallthewirelessfixturecontrol.Pushonthecenterofthe

wireless fixture control.

Connector(poke-instyle)

• 18to22AWG(0.75to0.3mm2)solidcopperwire

• Wirestriplength:0.31in(8mm)

Mounting Thickness

Snapsenablemountingtothefollowingmaterialthicknessranges:

• 0.04in(1mm)orless

• 0.041to0.08in(1.1to2mm)

• 0.081to0.13in(2.1to3.3mm)

WARNING! Shock Hazard. May result in serious injury or death.

Turn off power at circuit breaker before installing the unit.

Formoreinformation,see

www.lutron.com/TechnicalDocumentLibrary/3691039.pdf

Please read before installing.

One Fixture Control At least one EcoSystem driver + Wireless Sensor Interface (PS-OEM-2W-UNV)

At least one driver with self-powered DALI link

9.5–20.5 V-

80-250 mA

041600

Rev. A

03/2017

For set-up, programming, and

troubleshooting with a Vive system,

please refer to the installation

instructions included with the Vive hub

or at www.lutron.com

Clear Connect Wireless Fixture Controllers

UL2043PlenumRated

Controlsupto4ballastsordrivers(IEC60929AnnexE.2requireseachballastor

drivertolimitthesink/sourcecurrentdrawto2.0mAmaximum).

DefaultFunctionality

Fixture Controls

Auto On level: DFCSJ-OEM-OCC only

(notapplicableforDFCSJ-OEM-VAC orDFCSJ-OEM-RF)

Varieswithambientlightlevelwhenoccupancyistriggered

(e.g.,100%foradarkroom,10%forabrightroom).

Timeout period:15minutes

Connector buttons

0.04in(1mm)

or less

0.041to0.08in

(1.1to2mm)

0.081to0.13in

(2.1to3.3mm)

DaylightingSensor

Donotinstallindirectviewofthelightsourceorreflectingsurface.

PIRSensor

• Installinalocationthatallowsthesensortohaveanunobstructedviewofthearea.

• Installawayfromradiatedheatgivenoffbythelightsource.

Temperature

Thewirelessfixturecontrolisratedfor55°C(131°F)maximum.Productmustbeinstalledinanarea

thatwillnotallowittoexceedthisrating.Keepawayfromheatgeneratingdevices(e.g.,drivers)and

verifyduringthefixturedesignprocess.

WiringBestPractices(forRFconsideration)

• Keepallthefixturewiringtotheminimumlengthneededtoachievetheconnectionsinanorganizedmanner.Avoidunnecessaryslackinthe

wires.

• Ifthedriverisprovidedwithagroundterminal,thisterminalmustbeelectricallyconnectedtothegroundedfixturemetalusingagroundwire

thatisnolongerthan2in(51mm).

• Mechanically affix all the wires to the fixture wall so that they are kept as close possible to the grounded fixture metal.

• Ensurethatthedriverwiringisasfaraspossiblefromthewiringimmediatelyconnectedtothewirelessfixturecontrol

• EnsurethatthewirelessfixturecontrolismountedawayfromtheLEDstripstominimizethecouplingoftheRFradiationfromtheLEDstrips

into the wireless fixture control.

• Formoreinformation,seewww.lutron.com/TechnicalDocumentLibrary/048620.pdf

Wirelessfixturecontroller(RFonly)

•TheWirelessfixturecontroller(RFonly)(DFCSJ-OEM-RF)canbeinstalledonthebackofthefixture,assumingmetaltilesarenotbeingused.

• TheWirelessfixturecontroller(RFonly)willberatedforuseinplenumareas.

• Donotfullyenclosewithinthemetalfixture.

MountingtoCurvedSurfaces

Mountingdirectlytoacurvedsurfaceisnotrecommended.Anadaptor(custommanufacturedbytheOEM)mayberequiredtoensurethat

thedeviceisseatedproperly.

Remote Mounting

The wireless fixture control is intended for troffer and linear fixtures and is not intended to be ceiling mounted.



WiringDiagrams

120–277V~

Wireless sensor interface

EcoSystem/DALIdriver

Driverwithself-poweredDALIlink

EcoSystemdriver

Driverwithself-poweredDALIlink

Clear Connect Wireless

Fixture Controller

Clear Connect Wireless

Fixture Controller

Button

PIRlens

Daylight

sensor lens

Daylight

sensor lens

FCC information and IC information

Thisdevicecomplieswithpart15oftheFCCRulesandIndustryCanada

license-exemptRSSstandard(s).Operationissubjecttothefollowing

twoconditions:(1)Thisdevicemaynotcauseinterference,and(2)this

devicemustacceptanyinterference,includinginterferencethatmay

causeundesiredoperation.Modicationsnotexpresslyapprovedby

LutronElectronicsCo.,Inc.couldvoidtheuser’sauthoritytooperatethis

equipment.

NOTE: This equipment has been tested and found to comply with the

limitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules.

Theselimitsaredesignedtoprovidereasonableprotectionagainst

harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,

usesandcanradiateradiofrequencyenergyand,ifnotinstalledandused

inaccordancewiththeinstructions,maycauseharmfulinterferenceto

radiocommunications.However,thereisnoguaranteethatinterference

willnotoccurinaparticularinstallation.Ifthisequipmentdoescause

harmfulinterferencetoradioortelevisionreception,whichcanbe

determinedbyturningtheequipmentoffandon,theuserisencouraged

to try to correct the interference by one or more of the following

measures:

• Re-orientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthatto

whichthereceiverisconnected.

Clear Connect Wireless Fixture Controllers with

Ecosystem or DALI Driver

Wireless Fixture Control with Driver with

Self-powered DALI Link

LS+

S-

E+

E-

Wireless sensor interface

120–277V~

ALL PROGRAMMING IS OPTIONAL

Programming is not required for default functionality

ResetFactoryDefaults

Note:Insomeinstances,itmaybenecessarytoresetthe

xturecontrollersandconnecteddevicesbacktofactory

defaultsettings.Beforebeginning,makesurethatall

devicesareconnectedandpowered.

Rapidly tap the button on the xture controller three times

andholdonthefourthuntiltheLEDbeginstoashslowly;

release button.

Within1secondofreleasingthebutton,againrapidly

tapthebuttonthreetimesandtheLEDswillashrapidly

indicating that the unit has been reset to factory defaults.

Note:Anyassociationsorprogrammingpreviouslysetup

with the xture control will be erased and will need to be

re-programmed.

Clear Connect Wireless Fixture

Controllers

Part of the Vive Family

Limited Warranty:

http://www.lutron.com/TechnicalDocumentLibrary/369-119_Wallbox_Warranty.pdf

Troubleshooting

*www.lutron.com

Symptom Solution

Sensordoesnotrespond

to motion.

• Sensorrequires2-minutewarmupperiodfrompowerresetbeforesensingcircuitisactive.

Defaulttimeoutis15minutes.

Lightsdonotdimorturn

ONasexpected.

• Ensurethatcontrollinesarewiredproperly

Lightsareunstableat

low-end.

• Adjustlow-endtrim.RefertoVivedocumentationonwww.lutron.com.

Customer Assistance | 1.844.LUTRON1 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299 USA

Lutron,Pico,PowPak,EcoSystem,andEnergiTriPakaretrademarksofLutronElectronicsCo.,Inc.registeredintheU.S.andothercountries.RadioPowrSavrandVivearetrademarksofLutronElectronicsCo.,Inc.

NECisaregisteredtrademarkoftheNationalFireProtectionAssociation,Quincy,Massachusetts.

For set-up, programming, and troubleshooting with a

Vive system, please refer to the installation instructions

included with the Vive hub or at

www.lutron.com

Recommended end-of-line test

1. Providepowertoxture.

2. Fixturewillgotothedriver’ssavedlevel.

3. Pressthebuttontotoggletheloadstate.LightwillfadetoON

(orOFF)over1second.GreenLEDwillstaylitfor2secondsafter

releasing the button.

4. Toggletheloadagain(ifnecessary)toensurethelightsareon.

ThiswillmakesurethelightsturnONwhenpowerisappliedthe

nexttime(atjobsite).

5. Removepower.

If testing occupancy sensor functionality:

1. Applypowertoxture.

2. Pressbutton(ifnecessary)toturnlightsoff.

3. Waitfor2minutesforsensoroccupancycircuittobecomeactive

4. Providemotioninfrontofsensor-lightswillturnON.

5. Lightswillnottunoffautomaticallyfor15minutesafterlast

motion detection.

If testing daylight sensor functionality:

1. Applypowertoxture.Fixtureshouldturnontofull(highend).If

not,pressbuttononsensor.

2. Shinelightsource(ashlight)directlyintodaylightlens.Fixture

lightwilldimdownover1minute(holdashlightsteadilyinplace).

3. Coverdaylightlens/buttonwithopaquematerial.Fixturelightwill

dimupover1minute(holdopaquematerialsteadilyinplace)

Este manual sirve para los siguientes modelos

Otros manuales de Controladores de Lutron Electronics

Lutron Electronics

Lutron Electronics GRX-LC8 Manual

Lutron Electronics

Lutron Electronics FS-SE Manual de usuario

Lutron Electronics

Lutron Electronics Vive Series Manual de usuario

Lutron Electronics

Lutron Electronics seeTouch Manual de usuario

Lutron Electronics

Lutron Electronics Energi Savr Node QS QSNE-4S10-D Instrucciones de funcionamiento

Lutron Electronics

Lutron Electronics AYFSQ-F Manual de usuario

Lutron Electronics

Lutron Electronics L3D0-96W24V-U Manual de usuario

Lutron Electronics

Lutron Electronics LTEA4U1UKL Series Manual de usuario

Lutron Electronics

Lutron Electronics LHD0-96W24V-U UL Manual de usuario

Lutron Electronics

Lutron Electronics Grafik Eye GRX-TVI Manual de usuario

Lutron Electronics

Lutron Electronics LHD0-96W24V-U UL Manual de usuario

Lutron Electronics

Lutron Electronics Sivoia QED Manual de usuario

Lutron Electronics

Lutron Electronics Maestro Manual de usuario

Lutron Electronics

Lutron Electronics YFSQ-F Manual de usuario

Lutron Electronics

Lutron Electronics GRAFIK Eye QS Manual del propietario

Lutron Electronics

Lutron Electronics PowPak RMKS-DAL4-SZ Manual de usuario

Lutron Electronics

Lutron Electronics PowPak FCJ-010 Manual de usuario

Lutron Electronics

Lutron Electronics WC-4M-GC Instrucciones de montaje

Lutron Electronics

Lutron Electronics Hi-lume Premier Manual de usuario

Lutron Electronics

Lutron Electronics AYFSQ-F Manual de usuario

Lutron Electronics

Lutron Electronics QS IR Eye Manual del propietario

Lutron Electronics

Lutron Electronics Homeworks QS seeTouch HQWIS-NB-NONE Manual de usuario

Lutron Electronics

Lutron Electronics GRAFIK Eye GRX-4M-GC Instrucciones de montaje

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario