LumaSense IN 5-H-PL2 Manual de usuario

IN 5-H-PL2

IMPAC-Pyrometer

Operation Manual · Betriebsanleitung

Proven Quality

IMPAC-Pyrometer IN 5-H-PL2

Contents

General ....................................................................................... 3

Information about the user manual ............................................................3

Limit of liability and warranty ......................................................................3

Terminology................................................................................................3

Disposal / decommissioning.......................................................................4

Safety .........................................................................................................4

Appropriate use..........................................................................................4

1Technical data ...................................................................... 5

2Dimensions ........................................................................... 6

3Laser targeting light .............................................................. 6

4Optics.................................................................................... 6

5Electrical connection............................................................. 7

Connection .................................................................................................7

6Factory settings..................................................................... 7

7Accessories .......................................................................... 8

8Maintenance ......................................................................... 8

9Appendix............................................................................... 8

Caution: Safety Advice

Do not look directly into laser beam

Caution

The lens has an anti-reflecting coating.

If cleaning the lens use a soft, dry cloth such

as that used to clean camera objectives

IMPAC-Pyrometer IN 5-H-PL2

General

Information about the user manual

Congratulations on choosing this high quality and highly efficient IMPAC py-

rometer.

Please read this manual carefully and step for step including all notes to secu-

rity, operation and maintenance before installing the pyrometer. For installation

and operation of the instrument this manual is an important source of informa-

tion and work of reference. To avoid handling errors keep this manual in a

location where you always have access to. When operating the instrument, it

is necessary to follow the generally safety instructions.

Additionally to this manual the manuals of the components used are valid. All

notes – especially safety notes – are to be considered.

Should you require further assistance, please call our customer service hotline

in Frankfurt, Germany, +49 (0)69 973 73-0.

Limit of liability and warranty

All general information and notes for handling, maintenance and cleaning of

this instrument are offered according to the best of our knowledge and experi-

ence.

LumaSense Technologies GmbH is not liable for any damages that arise from

the use of any examples or processes mentioned in this manual or in case the

content of this document should be incomplete or incorrect. LumaSense Tech-

nologies reserves the right to revise this document and to make changes from

time to time in the content hereof without obligation to notify any person or

persons of such revisions or changes.

All series 5 Instruments from LumaSense Technologies GmbH have a war-

ranty of two years from the invoice date. This warranty covers manufacturing

defects and faults which arise during operation only if they are the result of

defects caused by LumaSense Technologies GmbH.

This warranty is void if the instrument is disassembled, tampered with, altered

or otherwise damaged, without prior written consent from LumaSense Tech-

nologies.

Terminology

The used terminology corresponds to the VDI- / VDE-directives 3511, page 4.

IMPAC-Pyrometer IN 5-H-PL2

All copyrights reserved. This document may not be copied or published, in part

or completely, without the prior written permission of LumaSense Technolo-

gies GmbH. Contraventions are liable to prosecution and compensation. All

rights reserved.

Disposal / decommissioning

Inoperable IMPAC pyrometers have to be disposed corresponding to the local

regulations of electro or electronic material.

Safety

Each person working with the pyrometer must have read and understood the

user manual before operation. Also this has to be done if the person already

used similar instruments or was already trained by the manufacturer.

The pyrometer has only to be used for the purpose described in the manual. It

is recommended to use only accessories offered by the manufacturer.

Follow common safety regulations for mains voltage (230 or 115 V AC) con-

necting additional devices operating with this mains voltage (e.g. transform-

ers). Touching mains voltage can be fatal. An incorrect connection and mount-

ing can cause serious health or material damages.

Only qualified specialists are allowed to connect such devices to the mains

voltage.

Appropriate use

The IMPAC pyrometer IN 5-H-PL2 is a stationary infrared thermometer for

non-contact temperature measurement of non-metallic surfaces or painted,

coated or anodized metals with a temperature range from 0 to 250°C.

IMPAC-Pyrometer IN 5-H-PL2

1 Technical data

Measuring range: 0 ... 250°C

Optics: Si lens (see chart)

IR Detector: Thermopile

Spectral response: 8 ... 14 µm (no influence by water vapour or CO2)

Output signal: 4 ... 20 mA load independent DC, linear,

galvanically isolated

Internal processing of

measured data :

digital

Max load: 500  24 V DC

Emissivity: 0.95; fixed

Response time (t90)*: 8 ms; fixed

Accuracy**:

(ε= 1, t90 = 1s

Tamb.=constant)

15 ... 30°C: 1 °C

0 ... 15 / 30 ... 45°C: 1.5 °C

45 ... 70°C: 2 °C

Repeatability**:

(ε= 1, t90 = 1s,

Tamb.=constant)

0.5°C

Noise Equivalent Tem-

perature Difference

(NETD):

(ε= 1, = 1, Tamb.=23°C)

0.1 °C measured temperature = 23°C

Alignment: integrated laser targeting light, class II, total power

<1 mW, = 650 nm, focused at 100 mm

Safety system: IP65 (with mounted connector)

Operating temperature: 0 ... 70°C

Storage temperature: -20 ... 70°C

Power supply: 10 ... 30 V DC ripple must be less

then < 0.5 V, 65 mA max. (incl. laser)

Housing: Stainless steel

Dimensions: 104.5 mm x 49.5 mm (LxD)

(length with connector: 153 mm)

Weight: 380 g

Mounting position: any

CE-Label complies with EC rules about electric immunity

Order no.: 3 869 920

Connection cable: A connecting cable is not included with the instru-

ment and should be ordered separately (see 7.

Accessories).

* according IEC/TS 62492-1 Edition 1.0 2008-04

** The instrument must be at a constant ambient temperature for a minimum of 15 minutes

IMPAC-Pyrometer IN 5-H-PL2

2 Dimensions

3 Laser targeting light

For aligning, the IN 5-H-PL2 has an integrated laser targeting light. The target-

ing light is switched on by a short push on the push button at the rear cover.

The laser is focused at a distance of 100 mm. After 2 minutes the targeting

light is turned off automatically. Operating temperatures above 50°C will switch

off the laser targeting light automatically.

4 Optics

Push button for

targeting light

IMPAC-Pyrometer IN 5-H-PL2

5 Electrical connection

The series 5 pyrometers are powered by 24 V DC nominal (possible range: 10

... 30 V DC, ripple must be less than 0.5 V). When connecting the device to the

power supply ensure correct polarity. The instrument has no warm-up time,

with connection to the power the instrument operates immediately. To switch

off the instrument, interrupt the power supply or unplug the electrical connec-

tor.

Analog output and power supply are galvanically insolated.

To meet the electromagnetic requirements (EMV), a shielded connecting cable

must be used. The shield of the connecting cable is usually only connected on

the pyrometer side. If the connecting cable is extended, the extension cable

also needs to be shielded. Do not connect the shield to the power source side

(control cabinet), to avoid ground loops.

Connection

GFE

Pin assignment

(side of male inserts)

Pin K white + 24 V supply voltage

Pin A brown 0 V supply voltage

Pin B yellow - linear output

Pin L green + linear output

Pin M blue screen

(do not connect to control cabinet)

6 Factory settings

Emissivity (Emi): 95%

Response time (t90): min (8 ms)

Analog output: 4 ... 20 mA

IMPAC-Pyrometer IN 5-H-PL2

7 Accessories

3 852 290 Power supply NG DC (100...240V AC to 24 V DC)

3 821 470 Connection cable, 5 m

3 821 190 Connection cable, 10 m

3 821 290 Connection cable, 15 m

3 890 640 LED digital display DA 4000-N

3 890 650 LED digital display DA 4000, with 2 set-point relays

3 890 520 LED digital display DA 6000 with 2 set-point relays,

RS232 output, analog output and maximum value storage unit

3 890 530 DA 6000 with RS485

3 834 210 Adjustable mounting support

3 835 160 Air purge unit

8 Maintenance

The pyrometer does not have any parts which require regular service, only the

lens has to be kept clean. The lens can be cleaned with a soft cloth for clean-

ing glasses or photo objectives.

The Si-lens of the IN 5-H-PL2 has an anti-reflective coating which appears

slightly colored. Be extremely careful - this layer can easily be rubbed off - this

will greatly affect the measuring results!

9 Appendix

Output current vs. temperature

T [°C] I [mA]

0 4.00

20 5.28

40 6.56

60 7.84

80 9.12

100 10.40

120 11.28

140 12.96

160 14.24

180 15.52

200 16.80

220 18.08

240 19.36

250 20.00

IMPAC-Pyrometer IN 5-H-PL2

Inhalt

Allgemeines ...............................................................................10

Informationen zur Betriebsanleitung ........................................................10

Haftung und Gewährleistung ...................................................................10

Terminologie ............................................................................................11

Urheberschutz..........................................................................................11

Entsorgung / Außerbetriebnahme............................................................11

Sicherheit .................................................................................................11

Bestimmungsgemäße Verwendung.........................................................11

1Technische Daten................................................................12

2Abmessungen......................................................................13

3Laserpilotlicht.......................................................................13

4Optik ....................................................................................13

5Elektrischer Anschluss.........................................................14

Belegung des Anschlusskabels ...............................................................14

6Werkseinstellungen .............................................................14

7Zubehör ...............................................................................15

8Wartung ...............................................................................15

9Anhang ................................................................................15

Achtung : Sicherheitshinweise

Nicht in den Laserstrahl hineinsehen

Achtung

Linse ist mit einer Entspiegelungsschicht versehen.

Bei Verschmutzung nur vorsichtig mit einem

weichen, trockenen Mikrofasertuch reinigen

IMPAC-Pyrometer IN 5-H-PL2

Allgemeines

Informationen zur Betriebsanleitung

Wir beglückwünschen Sie zum Kauf dieses hochwertigen und leistungsfähigen

IMPAC-Pyrometers.

Lesen Sie diese Betriebsanleitung mit allen Hinweisen zu Sicherheit, Bedie-

nung und Wartung bitte sorgfältig Schritt für Schritt durch. Sie dient als wichti-

ge Informationsquelle und Nachschlagewerk für Installation und Betrieb des

Gerätes. Zur Vermeidung von Bedienungsfehlern muss diese Anleitung so

aufbewahrt werden, dass jederzeit darauf zugegriffen werden kann. Die allge-

meinen Sicherheitsbestimmungen müssen bei Betrieb des Gerätes unbedingt

eingehalten werden.

Neben dieser Betriebsanleitung gelten die Betriebsanleitungen der mitbenutz-

ten Komponenten. Die darin enthaltenen Hinweise – insbesondere Sicher-

heitshinweise – sind zu beachten.

Sollten weitergehende Fragen auftreten, steht Ihnen unser technischer Kun-

dendienst unter der Rufnummer +49 (0)69 973 73-0 in D-60326 Frankfurt tele-

fonisch gerne zur Verfügung.

Haftung und Gewährleistung

Alle Angaben und Hinweise für die Bedienung, Wartung und Reinigung dieses

Gerätes erfolgen unter Berücksichtigung unserer bisherigen Erfahrung nach

bestem Wissen.

LumaSense Technologies GmbH übernimmt keine Haftung für die in diesem

Handbuch aufgeführten Beispiele und Verfahren oder für Schäden, die daraus

eventuell entstehen könnten oder für den Fall, dass der Inhalt dieses Doku-

ments möglicherweise unvollständig oder fehlerhaft ist. LumaSense behält

sich das Recht vor, Änderungen an diesem Dokument und den darin be-

schriebenen Produkten vorzunehmen, ohne die Verpflichtung einzugehen,

irgendeine Person über solche Änderungen zu informieren.

LumaSense Technologies GmbH gibt auf alle Geräte der Serie 5 eine Ge-

währleistung von zwei Jahren ab Datum der Rechnungslegung. Diese bezieht

sich auf Fabrikationsfehler sowie Fehler, die sich während des Betriebes ein-

stellen und auf einen Fehler der Firma LumaSense Technologies GmbH hin-

weisen. Die Gewährleistung erlischt, wenn das Gerät ohne vorherige schriftli-

che Zustimmung von LumaSense Technologies auseinandergenommen, ver-

ändert oder anderweitig zerstört wurde.

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de LumaSense

LumaSense

LumaSense IS 50-LO plus Manual de usuario

LumaSense

LumaSense IMPAC IS 310 Manual de usuario

LumaSense

LumaSense 320 Series Manual de usuario

LumaSense

LumaSense IMPAC IN 500 Series Manual de usuario

LumaSense

LumaSense IMPAC IN 140/5 Manual de usuario

LumaSense

LumaSense IN 300/5 Manual de usuario

LumaSense

LumaSense SmartDGA Manual de usuario

LumaSense

LumaSense IS 12 Manual de usuario

LumaSense

LumaSense IGA 15 plus Manual de usuario

LumaSense

LumaSense IMPAC ISR 12-LO/GS Manual de usuario

LumaSense

LumaSense IS 12-TSP Manual de usuario

LumaSense

LumaSense SmartDGA Manual de usuario

LumaSense

LumaSense IMPAC IGA 140/23 Manual de usuario

LumaSense

LumaSense IN 210 Manual de usuario

LumaSense

LumaSense Impac INFRATHERM ISR 50-LO Manual de usuario

LumaSense

LumaSense 140 Series Instrucciones de instalación y funcionamiento

LumaSense

LumaSense 140 Series Instrucciones de instalación y funcionamiento

LumaSense

LumaSense Impac IS 5 Manual de usuario

LumaSense

LumaSense IMPAC IS 140 Manual de usuario

LumaSense

LumaSense IS 8 pro Manual de usuario

LumaSense

LumaSense IMPAC IPE 140 Manual de usuario

LumaSense

LumaSense 320 Series Manual de usuario

LumaSense

LumaSense 5 Series Manual de usuario

LumaSense

LumaSense IN 5 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario