Lovibond SD 50 pH Manual de usuario

SD 50

Lock/Unlock Data!

C. Select pH/mV

D. Backlight ON/OFF

____________________________________________________________________________________________

Note: Icons/Characters in RED meaning "BLINK"

: Hit once / : Press and hold / : Release

F. Store Data

1. In lock mode: 2s

2. In measurement mode: 2s (or 2s )

3. When the storage is full, it will overwrite the oldest data.

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

G. System Setup

Menu selection:

2s (latest memory#)

(7.00 or 6.86) (dd-mm-yy/24hr or mm-dd-yy/12hr) (°C or °F)

(31-12 24 or 12-31 12ampm) .....

To enter:

F. pH Buffer 7.00 -> 4.00 -> 10.00

MEASUREMENT

pH CALIBRATION

Immerse the probe

into pH7 buffer

solution. Exit here for one

point calibration

Exit here for two

point calibration

or go for second point calibration as follows:

or go for third point calibration as follows:

wait

Clean the probe ﬁrst,

then immerse into pH4

buffer solution.

Clean the probe ﬁrst,

then immerse into

pH10 buffer solution.

(4) (7) (10)

on the Display

Remove protective cap from the probe

E. Store Data

Three point calibration

ﬁnished.

L M H

Low, Middle, High

Press

Press for

3 seconds

Insert the batteries

unlock

off

unlock

off

Automatically turns off after 8 minutes of

inactivity.

Possible slight delay after pressing

before freeze of the data (!).

Mode „mV“ does not show ORP on the display,

only milivolts.

to switch, unfreeze data (see B).

After 3 sec. the ﬁle no. temporarily appears

on the display, e.g. 02.

Once the storage has reached max. capacity,

the data will overwrite the oldest ﬁles.

off

lock

• Re-Calibrate according to individual recommendations! Rinse the electrode with destilled water after each measurement.

• Choose Lovibond Standard Solutions or produce them with buffer tablets according to the kit manual (see backside).

Remove protective cap from the probe.

Power ON (see A)

Characters in RED represent „Flashing symbols“.

4 5 6

1 2 3

www.ssb-berlin.de

V. Set Data/Time display type

VI. Electrode Replacement

SETUP

I. Recall Data

II. Select Buffer System

III. Set Date and Time

IV. Set Temperature system (°C/°F)

Recall Data

go to l.

Set Temperature

go to lV.

Select Buffer System

go to ll.

Set Data/Time display

type go to V.

Set Date and Time

go to lll.

To enter.

3 sec

Minutes

24 h

Hours

Year

Month

Day

Month

pH Buffer

Order Codes

721250 pH buffer-set 4.00/7.00/10.00 (25°C)

721252 pH buffer 4.00 (25°C) 1 litre

721254 pH buffer 7.00 (25°C) 1 litre

721256 pH buffer 10.00 (25°C) 1 litre

515600 Buffer tablets pH 10 100 pc.

515601 Buffer tablets pH 10 250 pc.

515610 Buffer tablets pH 7 100 pc.

515611 Buffer tablets pH 7 250 pc.

515620 Buffer tablets pH 4 100 pc.

515621 Buffer tablets pH 4 250 pc.

Accessories

1950017 Battery CR 2032 (2 Batteries required)

194820 pH replacement electrode

384801 Beaker, 100 ml

Preparation of buffer solution

1. FilI a clean beaker with 20 ml deionised/

distilled water.

2. Add one buffer tablet of the required pH-

value and shake or crush with a clean

stirring rod until the tablet disintegrates.

3. Allow to stand for about two minutes

to ensure that the buffer is completely

dissolved and to allow any insoluble

particles to settle.

4. Immerse the electrode into the beaker

and calibrate the SD 50 in accordance

with this instruction manual.

5. Remove the electrode and rinse it tho-

roughly.

6. Use the buffer solution only once.

Note

It is important to rinse the

electrode before immerse in

a buffer solution of a different

value.

Accuracy

Fresh buffer solutions should

always be made up in dei-

onised/distilled water. The

maximum tolerance based

on the pH values 4, 7 and 10

is ±0.05 pH.

Warranty

The waterproof SD 50 is war-

ranted to be free from manu-

facturing defects for 2 years

and electrode (probe) modul

for 6 months.

G. System Setup

Unfreeze data ﬁrst (see frontside B) before Menu selection.

Delete stored data.

Automatic Exit

Select V. `Set Data/ Time display type‘ ﬁrst.

to increase (+);

new electrode

No.: 00386910

to decrease (-)

Adjustment:

Press for

further ﬁles. Exit

Exit

°C °C

select select

°F

123

4 5 6

Content

1 pH Meter SD 50 in a robust

plastic case with strap

2 Batteries

10 pH 4 Buffer tablets (1 strip)

10 pH 7 Buffer tablets (1 strip)

10 pH 10 Buffer tablets (1 strip)

1 Lenyard

1 Instruction Manual

Instruction manuals available in further languages, visit www.lovibond.com

SD 50 pH Specications/Features

am/pm

12 hour clock

or 24 hour

clock

am/pm 12 hour clock

24 hour clock

Characters in RED represent „Flashing symbols“.

www.ssb-berlin.de

Otros manuales de Instrumento de medición de Lovibond

Lovibond

Lovibond CheckitDirect Manual de usuario

Lovibond

Lovibond Tintometer SensoDirect Con110 Manual de usuario

Lovibond

Lovibond Scuba II Manual de usuario

Lovibond

Lovibond TG 60/268 Instrucciones de montaje

Lovibond

Lovibond Photometer-System MD100 Manual de usuario

Lovibond

Lovibond SensoDirect pH110 Manual de usuario

Lovibond

Lovibond MD 100 Manual de usuario

Lovibond

Lovibond PFX995 Series Instrucciones de montaje

Lovibond

Lovibond CheckitDirect Manual de usuario

Lovibond

Lovibond MD200 Manual de usuario

Lovibond

Lovibond MD200 Manual de usuario

Lovibond

Lovibond TB300 IR Manual de usuario

Lovibond

Lovibond SD 50 Manual de usuario

Lovibond

Lovibond Photometer-System MD100 Manual de usuario

Lovibond

Lovibond SD 90 Manual de usuario

Lovibond

Lovibond Tintometer MD100 Manual de usuario

Lovibond

Lovibond RT 400 Manual de usuario

Lovibond

Lovibond MD200 Manual de usuario

Lovibond

Lovibond MD200 Manual de usuario

Lovibond

Lovibond SD 60 REDOX Manual de usuario

Lovibond

Lovibond Photometer-System MD100 Manual de usuario

Lovibond

Lovibond Tintometer MD100 Manual de usuario

Lovibond

Lovibond SensoDirect pH200 Manual de usuario

Lovibond

Lovibond Tintometer SensoDirect Salt110 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario