Lockly LATCH EDITION SECURE PGD628 Manual de usuario
INSTALLATION
GUIDE
LATCH EDITION
SECURE
PGD628 |PGD628F | PGD628FC
Reference installation parts overview foldout on back page
Welcome!
This guide will walk you through step-by-step how to
install and get your Lockly Secure up and running.
Installation generally takes less than 30 minutes. If
you have any questions please reference our online
support at: Lockly.com/support or call (669) 500-8835
for help.
2
Preparation
Phillips Screwdriver
To complete the installation you will need:
Flathead Screwdriver Tape measure or ruler
Pliers
（Optional）
Screwdriver with drill bits
Drilling is not required to install the lock, and is optional. However if you are installing your lock on
a brand new door, a drill is required if there are no holes prepared for
lock installation.
3
Preparation
1-3/8" ~ 2"
(35mm ~ 50mm)
2-1/8"
54mm
4-1/8"
105mm
1"
25mm
Backset
IMPORTANT NOTICE
1/2"
12mm
2-3/8" (60mm)
or 2-3/4" (70mm)
Measure and confirm your door is between
1-3/8" ~
2" (
35mm - 50mm).
Measure and confirm the hole in the door
door is 2-1/8" (54mm).
Measure and confirm that the backset is
between 2-3/8" (60mm) to 2-3/4" (70mm).
Measure and confirm that hole in the door
edge is 1" (25mm).
*
You are not required to drill an extra hole in your door. We have provided double-sided
adhesive tape for you to help stabilize the lock during installation. Only drill a hole if you
wish to have added stability. Please refer to the provided template for drilling if needed.
Use goggles to protect your eyes if you need to drill door holes.
Remove existing door hardware, latch or deadbolts before installing the new lock.
Use provided template to bore new holes if needed.
1
2
3
4
*
*
*Optional
4
INSTALLING THE LOCKSET
Step 1
Facing the door exterior, install the lockset according to the in-swing or out-swing opening direction
of your door.
Secure lockset with provided G screws.
LEFT OUT-SWING DOOR
LEFT IN-SWING DOOR
RIGHT OUT-SWING DOOR
RIGHT IN-SWING DOOR
Inside
Inside
Outside
Outside
Inside
Outside
Inside
Outside
(a)
To ensure normal functions and stable long-term operation of
this lockset, replace your door’s old lockset with the provided
Lockly lockset. The included lockset is designed and optimized
for Lockly smart locks.
Measure the distance between center of front door hole to
the edge of your door. Push the shaft (a) to adjust the lockset
to 2-3/8"(60mm) or 2-3/4"(70mm).
2-3/4"
(70mm)
2-3/8"
(60mm)
Note: the shaft's horizontal
and vertical aligment must
be sustained during installa-
tion to ensure latch will fully
extend and lock securely.
5
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below
if you are unsure of you door orientation.
Changing the Exterior Handle Orientation
(Right handle)
Insert key and rotate lock
face so that the two white
dots align as shown.
12
R
Hinge
Side
RIGHT IN-SWING DOOR
LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR
LEFT IN-SWING DOOR
Use the provided pin insert Rto push the metal
pin located at the 3 o’clock of the the base handle,
then the other pin at 9 o’clock position. Remove
the
handle once the pins are
compressed.
INTERIOR
EXTERIOR
No need to change door handle
orientation. Skip Step 2.
LEFT-IN SWING and RIGHT OUT-SWING DOORS
require changing the door handle orientation.
Contnue to follow Step 2 to change exterior
and interior door handle orientation.
6
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
continued
Check that your handle works
smoothly by giving it a turn up
and down.
Twist key back to horizontal position. The
key can be taken out once it goes back
to the horizontal position.
34
56
Rotate the handle 180° to the other side of the
lock.
Using your fingers, press the two pins located on
the left and right side of the the lock to insert
the handle back onto the lock.
Confirm that your installation was complete
by checking if the pins are flush against
the handle, and has popped out. Adjust
the handle accordingly to make sure the
pins are fully decompressed and sits flush
against the surface.
7
Remove the screw by turning counter
clockwise and rotate the handle 180°
in the direction of the arrow as shown.
Make sure the screw hole is aligned with
the marker as illustrated.
Changing the Interior Handle Orientation
Securely screw clockwise as shown
to complete your handle orientation
change.
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
continued
12
8
PREPARING LOCK FOR INSTALLATION
Step 3
2
D
If you drilled a hole in Preparation, use Slotted Barrel Extension Uand use pliers to securely tighten
clockwise. If you did not drill a hole in Preparation, you can leave this pole removed.
1
Install Spindle Cwith
the holes side into the
base of the lock and
align the holes locate
in the 3 o’clock and
9 o’clock position.
Insert locking pin D
in to the hole as
shown above.
4Peel paper layer OFF the
Adhesive tape and
prepare for installation.
3
Carefully bend the end
of the locking pin D with
a needle nose pliers.
Failure to bend the locking
pin and turn the handle freely
without obstruction will result
to malfunction.
U
9
INSTALLING THE LOCK (EXTERIOR)
Step 4
1
2
3
Exterior
Install the exterior lock as shown to the
left by aligning the lock straight
and
passing the cable and attached rods
through the lockset.
Pass the Spindle Cthrough the center
of the lockset, and the round rods
through the sides in their respective
holes. The cable should run underneath
the lockset.
Align the lock straight and press hard (if
you use the Adhesive tape in step 3.4)
to secure the top of the lock.
Otros manuales para LATCH EDITION SECURE PGD628
2
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cerradura de puerta de Lockly
Lockly
Lockly ACCESS TOUCH PRO Manual de usuario
Lockly
Lockly Secure LUX Manual de usuario
Lockly
Lockly SECURE LUX MORTISE EDITION Manual de usuario
Lockly
Lockly Vision Manual de usuario
Lockly
Lockly DEADBOLT SECURE PLUS Manual de usuario
Lockly
Lockly PGD728F Manual de usuario
Lockly
Lockly SECURE PRO Manual de usuario
Lockly
Lockly ACCESS TOUCH PRO Manual de usuario
Lockly
Lockly LUX Compact Manual de usuario
Lockly
Lockly MORTISE EDITION SECURE LUX PGD829AFUS Manual de usuario
Lockly
Lockly DEADBOLT EDITION PGD1128FPW Manual de usuario
Lockly
Lockly FLEX TOUCH Manual de usuario
Lockly
Lockly DEADBOLT SECURE PLUS Manual de usuario
Lockly
Lockly Satin Nickel Secure Plus Smart Lock Deadbols Manual de usuario
Lockly
Lockly LATCH EDITION SECURE PGD628 Manual de usuario
Lockly
Lockly FLEX TOUCH Manual de usuario
Lockly
Lockly PRO Manual de usuario
Lockly
Lockly DEADBOLT EDITION 7S Manual de usuario
Lockly
Lockly DEADBOLT EDITION 7S Manual de usuario
Lockly
Lockly LUX COMPACT PGD688F-MB Manual de instrucciones
