LinMot B1100-PP Manual de usuario
Installation Documentation for the following Controllers:
-B1100-PP (-HC, -XC)
-B1100- F (-HC, -XC)
-B1100-GP (-HC, -XC)
Servo Controller Installation Guide
Document version: 3.9.2 / June 2009
Installation Guide B1100
© 2009 NTI AG
This work is protecte by copyright.
Un er the copyright laws, this publication may not be repro uce or transmitte in any form, electronic or mechanical, inclu ing
photocopying, recor ing, microfilm, storing in an information retrieval system, not even for i actical use, or translating, in whole
or in part, without the prior written consent of NTI AG.
LinMot® is a registere tra emark of NTI AG.
Note
The information in this ocumentation reflects the stage of evelopment at the time of press an is therefore without obligation.
NTI AG reserves itself the right to make changes at any time an without notice to reflect further technical a vance or pro uct
improvement.
Document version 3.9.2 / mk / June 2009
Page 2 of 18 Installation Gui e B1100 NTI AG/ LinMot/
Installation Guide B1100
Table of Content
IMPORTANT NOTES FOR B1100 SERIES CONTROLLERS......................................4
SYSTEM O ER IEW.....................................................................................................5
B1100 INTERFACES......................................................................................................6
FUNCTIONALITY............................................................................................................7
SOFTWARE....................................................................................................................7
POWER SUPPLY AND GROUNDING...........................................................................8
DESCRIPTION OF THE CONNECTORS / INTERFACES.............................................9
PHYSICAL DIMENSION...............................................................................................14
POWER SUPPLY REQUIREMENT..............................................................................15
ORDERING INFORMATION.........................................................................................16
INTERNATIONAL CERTIFICATIONS..........................................................................16
DECLARATION OF CONFORMITY CE-MARKING....................................................17
CONTACT ADDRESSES.............................................................................................18
NTI AG, LinMot Installation Gui e B1100 Page 3/18
Installation Guide B1100
Important notes for B1100 series controllers
C A U T I O N !
In order to assure a safe and error free operation, and to avoid severe
damage to system components, all system components must be
directly attached to a single ground bus that is earth or utility
grounded (see chapter Power Supply and Grounding).
Each system component should be tied directly to the ground bus
(star pattern), rather than daisy chaining from component to
component. (LinMot motors are properly grounded through their
power cables when connected to LinMot controllers) (see chapter
Power Supply and Grounding).
All connectors must not be con nected or disconnected while DC
voltage is present. Do not disconnect system components until all
LinMot controllers LEDs have turned off. (Capacitors in the power
supply may not fully discharge for several minutes after input voltage
has been disconnected). Failure to observe these precautions may
result in severe damage to electronic components in LinMot motors
and/or controllers.
Do not switch Power Supply DC oltage. All power supply switching
and E-Stop breaks should be done to the AC supply voltage of the
power supply.
Do not connect or disconnect the motors from controllers with
voltage present. Wait to connect or disconnect motors until all
LinMot controllers LEDs have turned off. (Capacitors may not fully
discharge for several minutes after power has been turned off).
Failure to observe these precautions may result in severe damage to
electronic components in LinMot motors and/or controllers.
Page 4 of 18 Installation Gui e B1100 NTI AG/ LinMot/
Installation Guide B1100
System Overview
Typical servo system B1100-XX-YY: Servo controller, motor an power supply.
NTI AG, LinMot Installation Gui e B1100 Page 5/18
Installation Guide B1100
B1100 Interfaces
B1100-PP /-HC/-XC
B1100- F /-HC/-XC
B1100-GP /-HC/-XC
Connector
X1 Motor Supply ● ● ●
X2 Motor Phases (Screw Terminals) ● ● ●
X3 Motor / Motor Signals ● ● ●
X5 Com / Config RS232, RS485, CAN ● ● ●
X7 RS485 / CAN In ● ● ●
X8 RS485 / CAN Out ● ● ●
X13 External/Simulate Position Enco er
Diff Hall Switches ● ● ●
X14 6 Digital Inputs
6 Digital Outputs
Analog In 0..10V
Analog In –10V.. +10V
Diff Step Dir zero
24V Logic Supply
● ● ●
LED State In icator ● ● ●
S4 Bus Termination ● ● ●
Page 6 of 18 Installation Gui e B1100 NTI AG/ LinMot/
Installation Guide B1100
Functionality
B1100-PP
B1100-PP-HC
B1100-PP-XC
B1100- F
B1100- F-HC
B1100- F-XC
B1100-GP
B1100-GP-HC
B1100-GP-XC
Supply oltage
Motor Supply 72VDC (24...85VDC) ● ● ● ● ● ● ● ● ●
Logic Supply 24VDC (22...26VDC) ● ● ● ● ● ● ● ● ●
Motor Phase Current
8A peak / 6A rms ● ● ●
15A peak / 9A rms ● ● ●
25A peak / 12A rms ● ● ●
Controllable Motors
LinMot P01-23x… ● ● ● ● ● ● ● ● ●
P01-37x… ● ● ● ● ● ● ● ● ●
P01-48x… ● ● ● ● ● ● ● ● ●
DC Motors ● ● ● ● ● ● ● ● ●
Brushless DC / EC Motors ● ● ● ● ● ● ● ● ●
Command Interface
Easy Steps Max. 6 Comman s ● ● ● ● ● ● ● ● ●
+/-10V Current Comman Interface ● ● ● ● ● ●
Step Direction In exer Interface ● ● ● ● ● ●
Cm Tab IO Interface (X14-IOs) (with EasySteps) ● ● ● ● ● ●
RS232 up to 115.2 kBau ● ● ●
RS485 up to 115.2 kBau ● ● ●
CANOpen up to 1MBau ● ● ●
DeviceNet 125, 250, 500 kBau ● ● ●
External Position Sensor
Incremental RS422 up to 2 MHz ● ● ● ● ● ● ● ● ●
Position Indexer Input
Step Dir Zero/ ABZ RS422 up to 2 MHz ● ● ● ● ● ●
Position Encoder Simulation
AB RS422 up to 2.5 MHz ● ● ● ● ● ●
Configuration
RS232 Configuration ● ● ● ● ● ● ● ● ●
CAN Multi Axes Configuration ● ● ● ● ● ● ● ● ●
Software
The configuration SW LinMotTalk1100 is free of charge an can be ownloa e from our home page.
For fast results see also the quick start gui es an configurations for the B1100-PP an B1100-VF
controllers:
•QuickStartGui e_B1100-PP.p f
•QuickStartGui e_B1100-VF.p f
This quick start gui es are istribute with the LinMotTalk1100 SW.
NTI AG, LinMot Installation Gui e B1100 Page 7/18
Installation Guide B1100
Power Supply and Grounding
*Insi e of the B1100 controller the PWR motor GND an PWR signal GND is connecte together an to
the GND of the controller housing. It is recommen e that the PWR motor GND is NOT groun e at
another place than insi e of the controller to avoi circular currents.
In or er to assure a safe an error free operation, an to avoi severe amage to system
components, all system components* must be well grounded to either a single earth
or utility ground. This inclu es both LinMot an all other control system components to
the same groun bus.
Each system component* shoul be tie irectly to the groun bus (star pattern), rather
than aisy chaining from component to component. (LinMot motors are properly
groun e through their power cables when connecte to LinMot controllers.)
Power supply connectors must not be con nected or disconnected while DC voltage
is present. Do not isconnect system components until all LinMot controllers LEDs have
turne off. (Capacitors in the power supply may not fully ischarge for several minutes
after input voltage has been isconnecte ). Failure to observe these precautions may
result in severe amage to electronic components in LinMot motors an /or controllers.
Do not switch Power Supply DC oltage. All power supply switching an E-Stop
breaks shoul be one to the AC supply voltage of the power supply. Failure to observe
these precautions may result in severe amage to controller.
Page 8 of 18 Installation Gui e B1100 NTI AG/ LinMot/
Installation Guide B1100
Description of the connectors / Interfaces
X1: Motor Supply
Screw Terminals Motor Supply: 72VDC nominal, 24...85VDC
Absolute max. Rating: 72VDC +20%.
External Fuse: 10AT for LC (8Apeak), 16AT for HC an XC (15A/25Apeak) servos.
If motor supply voltage excee s 90VDC, the controller will go into error state.
- Tightening Torque: min 0.4Nm
- Screw Threa : M 2,5
- Use 60/75°C copper con uctors only
- Con uctor Cross-Section 2.5mm2 (AWG14) max Length 4m
X2: Motor Phases
PH1+ /U
PH1- /V
PH2+ /W
PH2-
SCRN
LinMot Motor: 3-phase EC-Motor:
Motor Phase 1+ re Motor Phase U
Motor Phase 1- pink Motor Phase V
Motor Phase 2+ blue Motor Phase W
Motor Phase 2- grey
Shiel
Screw Terminals The motor phases are present at X2 an X3. It is recommen e to use X2. It is only allowe to use X3 for
connecting motor phases if RMS current is below 2A an peak current is below 4A.
Never connect motor phases on X2 an X3!
- Tightening Torque: min 0.4Nm
- Screw Threa : M 2,5
- Con uctor Cross-Section: max. 2.5mm2
- Use 60/75°C copper con uctors only
NTI AG, LinMot Installation Gui e B1100 Page 9/18
Installation Guide B1100
X3: Motor
1
2
3
4
5
6
7
8
9
case
LinMot Motor: 3-phase EC-Motor:
Motor Phase 1+
Motor Phase 2+
+5VDC +5VDC (Hall Supply)
Sensor Sine Hall 1
Temp. In Hall 3
Motor Phase 1-
Motor Phase 2-
AGND AGND (Hall Supply)
Sensor Cosine Hall 2
Shiel
DSUB-9 (f) Note:
Use +5V (X3.3) an AGND (X3.8) only for motor internal hall sensor supply (max. 100mA).
Caution:
Do NOT connect AGND (X3.8) to groun or earth!
It is only allowe to use X3 for connecting the motor phases if RMS current is below 2A an peak current
below 4A.
Motor Wiring for Phase Currents above 2A RMS 4A peak (recommended general wiring)
Important:
If motor phase current excee s 2ARMS or 4Apeak, motor phases must be wire to X2.
Motor wiring for Phase Currents below 2A RMS 4A peak
Page 10 of 18 Installation Gui e B1100 NTI AG/ LinMot/
Otros manuales para B1100-PP
3
Este manual sirve para los siguientes modelos
8
Tabla de contenidos
Otros manuales de Controladores de LinMot
LinMot
LinMot E1100-CO Manual de instrucciones
LinMot
LinMot Series E1400-GP Manual de usuario
LinMot
LinMot E1100 Series Manual de usuario
LinMot
LinMot E1100-GP Manual de usuario
LinMot
LinMot C1250-PD-XC-0S/1S Manual de usuario
LinMot
LinMot E1200-GP-UC Manual de instrucciones
LinMot
LinMot CC-Link IE Field Basic C1250-CC Series Manual de usuario
LinMot
LinMot E1250-PL Series Manual de usuario
LinMot
LinMot E1200-GP-UC Manual de usuario
LinMot
LinMot E100 Series Manual de usuario
