Linksys WTR54GS Manual de usuario
Wireless
1
A Division of Cisco Systems, Inc.
®
Model No.
Wireless
Quick Installation Guide
Model No.
WTR54GS (EU/LA)
Wireless-G
Package Contents
• Wireless-G Travel Router with SpeedBooster
• Setup CD-ROM with User Guide (English only)
• Power Cable (EU/UK)
• Ethernet Network Cable
• Quick Installation
24
,GHz
802.11g
Travel Router
with SpeedBooster
2
APower down your network
devices.
BLocate an optimum location for
the Router. The best place for the
Router is usually at the center of
your wireless network, with line of
sight to all of your mobile stations.
CConnect a standard Ethernet
network cable to the Router’s
Internet port. Then connect the
other end of the network cable to
your broadband modem.
DConnect your computer or
Ethernet device to the Router’s
ethernet port using standard
Ethernet network cabling.
EPower on the broadband
modem.
FConnect the AC power cable to
the Router’s Power port and the
other end into an electrical outlet.
GPower on the PC you wish to use
to configure the Router.
Proceed to Step 2.
C
D
1Connect the Router
There are two ways to configure the Router. Choose one of the following:
• Run the Setup CD-ROM - It is strongly recommended that you use the
Setup CD-ROM. Insert the Setup CD-ROM into the CD-ROM drive, and
follow the on-screen instructions.
•Use this Quick Installation guide - If you wish, you can use the Router’s
Web-based Utility. Proceed to Step 1 of this Quick Installation.
3
2
AOpen your web browser. Enter
http://192.168.16.1 in its
Address field. Press the Enter
key.
BA password request screen will
appear. Leave the User name
field blank, and enter the
default password, admin, in
the Password field. (For added
security, you should later set a
new password, using the
Administration tab’s
Management screen of the
Web-based Utility). Then click
the OK button.
CThe Web-based Utility will
appear with the Setup tab
selected. If requested by your
Internet Service Provider (ISP),
complete the Host Name and
Domain Name fields. (These
are usually requested by cable
ISPs.) Otherwise, leave them
blank.
C
Configure the Router
NOTE: Make sure your PC’s Ethernet
adapter is set to obtain an IP address
automatically. For more information,
refer to Windows Help.
B
A
4
DSelect one of the four Internet
Connection Type settings,
shown here. Each Setup
screen and available features
will differ depending on which
connection type you select.
Internet Configuration Type
Automatic Configuration - DHCP:
If you are connecting through
DHCP or a dynamic IP address
from your ISP, keep this default
setting.
Static IP: If your ISP assigns you a
static IP address, select Static IP
from the drop-down menu.
Complete the Internet IP Address,
Subnet Mask, Gateway, and DNS
fields. You need to enter at least
one DNS address.
PPPoE: If you are connecting
through PPPoE, select PPPoE from
the drop-down menu. Complete
the User Name and Password
fields.
Select Keep Alive if you always
want to be connected to your ISP,
or select Connect on Demand if
you are charged for the time that
you are connected to your ISP.
DHCP
Static IP
PPPoE
5
PPTP: PPTP is a service used in
Europe only.
Complete the Internet IP Address,
Subnet Mask, and Gateway fields.
Complete the User Name and
Password fields.
Select Keep Alive if you always
want to be connected to your ISP,
or select Connect on Demand if
you are charged for the time that
you are connected to your ISP.
EWhen you have finished
entering your Internet
connection settings, click the
Save Settings button to save
your changes.
FTo configure the Router for your
wireless network, select the
Wireless Tab’s Basic Wireless
Settings screen.
GSelect the Wireless Network
Mode:
Mixed: If your network has
Wireless-G and Wireless-B
devices, then keep the default
setting, Mixed.
G-Only: If your network only has
Wireless-G devices, select
G-Only.G
PPTP
6
B-Only: If your network only has
Wireless-B devices, select
B-Only.
Disable: If you want to disable
wireless networking, select
Disable.
HWireless Network Name (SSID).
The SSID is the network name
shared among all devices in a
wireless network. The SSID must
be identical for all devices in
the wireless network. It is case-
sensitive and must not have
more than 32 characters (use
any keyboard character). For
added security, you should
change the default SSID
(linksys) to a unique name.
IWireless Channel. Select the
appropriate channel from the
list provided to correspond with
your network settings. All
devices in your wireless network
must broadcast on the same
channel in order to function
correctly.
7
JWireless SSID Broadcast. When
wireless clients survey the local
area for wireless networks to
associate with, they will detect
the SSID broadcast by the
Router. To broadcast the
Router's SSID, keep the default
setting, Enable. If you do not
want to broadcast the Router's
SSID, then select Disable.
KChange these settings as
described here and click the
Save Settings button to apply
your changes.
LPower your broadband
modem off and back on
again.
MRestart or power on your PCs to
acquire the Router’s new
settings.
NTo test the Router’s settings,
open your PC’s web browser. In
the browser’s Address field,
enter
www.linksys.com/registration
and press the Enter key.
Congratulations! The installation of
the Wireless-G Travel Router with
SpeedBooster is complete.
IMPORTANT: Once the Router is
configured, wireless security, either
WEP or WPA, should be configured
to prevent security breaches in your
network.
NOTE: If your wireless adapters
support Secure Easy Setup (SES), you
can use the SES button on the Router
to set them up.
To do this: Press and release the
orange Cisco logo on the Router’s
front panel. When the logo turns white
and begins to flash, press the
adapter’s SecureEasySetup button.
(Up to 10 seconds may pass before
the light begins to flash.) The Router’s
Cisco logo will stop flashing when the
device has been added to the
network. Repeat this procedure for
any additional SecureEasySetup
device.
Refer to the User Guide for further
instructions.
8
3
The Router comes equipped with
four types of Wireless Security: WEP,
WPA Personal, WPA2 Personal, and
WPA2 Mixed. These security
methods are not enabled right out
of the box, however. Do configure
wireless security on the Router, do
the following:
AOpen the Router’s Web Utility
as shown in Step 2, and click
the Wireless tab. The Basic
Wireless Settings screen will
appear.
BSelect Wireless Security to
configure wireless security on
the Router.
Directions for the configuration
of WEP, WPA Personal, WPA2
Personal, and WPA2 Mixed
wireless security are provided
here.
CFrom the Security Mode pull-
down menu, select the type of
wireless security you’ll use on
your network.
WEP: WEP is a basic encryption
method, which is not as secure as
WPA. To use WEP, select a Default
Transmit Key (choose which Key to
use), and a level of WEP
encryption, 64 bits 10 hex digits
or 128 bits 26 hex digits. Then
either generate a WEP key using
the Passphrase or enter the WEP
key manually.
Configuring Wireless Security
NOTE: If your wireless adapters
support Secure Easy Setup (SES), you
can use the SES button on the Router
to set up Wireless Security.
Basic Wireless Settings
WEP Security Settings
9
WPA-Personal. This method offers
two encryption methods, TKIP and
AES, with dynamic encryption keys.
Select the type of encryption
method you want to use, TKIP or
AES. Enter the Passphrase, which
can have 8 to 63 characters. Then
enter the Key Renewal period,
which instructs the Router how
often it should change the
encryption keys.
WPA2-Personal. WPA2-Personal
gives you one encryption method,
AES, with dynamic encryption keys.
Enter a Passphrase of 8-63
characters. Then enter a Key
Renewal period, which instructs
the Router how often it should
change the encryption keys.
WPA2-Mixed. WPA2-Mixed gives
you TKIP+AES encryption. Enter a
Passphrase of 8-63 characters.
Then enter a Key Renewal period,
which instructs the Router how
often it should change the
encryption keys.
DClick the Save Settings button.
Congratulations! Wireless Security
is now configured on the Router.
WTR54GS-EU-LA_V2-QIG-50926NC JL
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2005
Cisco Systems, Inc. All rights reserved.
For additional information or troubleshooting
help, refer to the User Guide on the CD-ROM
or the Technical Support Insert. You can also
e-mail for further support.
Website
http://www.linksys.com/international
Product Registration
http://www.linksys.com/registration
WPA Personal
Security Settings
WPA2-Personal
Security Settings
Wireless
1
A Division of Cisco Systems, Inc.
®
Modelnr.
Wireless
Installationsvejledning
Modelnr.
WTR54GS (DK)
Trådløs-G
Pakkens indhold
• Trådløs-G Rejserouter med SpeedBooster
• Installations-cd-rom med brugervejledning
(kun på engelsk)
• Strømkabel (EU/UK)
• Ethernet-netværkskabel
• Installationsvejledning
24
,GHz
802.11g
Rejserouter
med SpeedBooster
Otros manuales para WTR54GS
3
Tabla de contenidos
Idiomas:
Otros manuales de Enrutador inalámbrico de Linksys
Linksys
Linksys WRT54G-TM Manual de usuario
Linksys
Linksys WRT160N - Wireless-N Broadband Router... Manual de usuario
Linksys
Linksys AC1750 Manual de usuario
Linksys
Linksys FGMM1000 Manual de usuario
Linksys
Linksys RT41P2-AT - Broadband Router With 2 Phone Ports At&t Service... Instrucciones de funcionamiento originales
Linksys
Linksys MR8300 Manual de usuario
Linksys
Linksys WRVS4400N - Small Business Wireless-N Gigabit Security... Manual de usuario
Linksys
Linksys WRT54GX2 - Wireless-G Broadband Router Manual de operación
Linksys
Linksys WRT150N - Wireless-N Home Router Wireless Manual de usuario
Linksys
Linksys WRT54GS Manual de usuario
Linksys
Linksys Linksys E1500 Manual de usuario
Linksys
Linksys EA-Series Manual de usuario
Linksys
Linksys WRV210 - Wireless-G VPN Router Manual de operación
Linksys
Linksys E1000 Manual de usuario
Linksys
Linksys WRT160NL - Wireless-N Broadband Router Manual de usuario
Linksys
Linksys WRT54G3G-VN Manual de operación
Linksys
Linksys E2500 Manual de usuario
Linksys
Linksys WRVS4400N - Small Business Wireless-N Gigabit Security... Manual de usuario
Linksys
Linksys WRT54G - Wireless-G Broadband Router... Manual de usuario
Linksys
Linksys WRT55AG - Wireless A+G Broadband Router Manual de usuario
