Linksys EA6350 V2 Manual de usuario
Product Overview
EA6350 V2
Top view
Indicator light—Stays on steadily while power is connected and following a successful Wi-Fi Protected Setup connection. Flashes
or pulses slowly during bootup, during firmware upgrades, and during a Wi-Fi Protected Setup connection. Flashes quickly
when there is a Wi-
Fi Protected Setup error.
Back view
Adjustable Antenna ports— The included 2 adjustable external antennas should be connected to the router before
powering it on. Twist the antenna connector clockwise onto the port on the router.
NOTE
For best performance, position the side antennas at a 30˚ angle
as shown in the picture on the left.
Wi-Fi Protected Setup™button— Press to easily configure wireless security on Wi-Fi Protected Setup-enabled network
devices.
USB port—Connect and share a USB drive or a USB printer.
Ethernet ports—Connect Ethernet cables to the blue gigabit (10/100/1000) ports and to wired Ethernet network devices.
NOTE
For best performance, use CAT5E or higher rated cables on the
Ethernet ports.
Internet port—Connect an Ethernet cable to this yellow port and to your modem.
Reset button—Press and hold for 10 seconds (until the port lights flash at the same time) to reset the router to its factory defaults.
You can also restore the defaults using Linksys Smart Wi-Fi.
Power port—Connect the included AC power adapter.
Power button—Press |(on) to turn on the router.
Setting Up Your EA-Series Router
Where to find more help
Linksys.com/support (documentation, downloads, FAQs, technical support, live chat, forums)
Linksys Smart Wi-Fi help (connect to Linksys Smart Wi-Fi, then click Help at the top of the screen)
How to install your router
To install your router:
If replacing an existing router, disconnect it. Power on your new router.
Connect the Internet cable from your modem to the yellow Internet port on your router. Wait until the power light on the front of
the router is solid.
Connect to the secure wireless name shown in the Quick Start Guide that came with your router. (You can change the network
name and password later during router setup.) If you need help connecting to the network, refer to your device documentation
CD. Note: You will not have Internet access until router setup is complete.
Open a web browser and follow the instructions to complete your router’s setup. If instructions do not appear in the web browser,
enter linksyssmartwifi.com in the browser’s address bar.
At the end of setup, follow the on-screen instructions to set up your Linksys Smart Wi-Fi account. Use Linksys Smart Wi-Fi to
easily manage your router’s settings, such as:
Change your router’s name and password
Set up guest access
Configure parental controls
Connect devices to your network
Test your Internet connection speed
NOTE:
As part of Linksys Smart Wi-Fi account setup, you will be sent a
verification e-mail. Make sure that you open the e-mail from Linksys
and click the provided link.
How to connect to Linksys Smart Wi-Fi
You can use Linksys Smart Wi-Fi to configure your router from any computer that has an Internet connection.
To open Linksys Smart Wi-Fi:
Click the Linksys Smart Wi-Fi icon on your desktop.
- OR -
Open a web browser and go to www.linksyssmartwifi.com.
Enter the e-mail address and password you set up earlierand click Log in.
How to change router settings
Use Linksys Smart Wi-Fi to change settings on your router and set up special features such as parental controls and guest access.
NOTE:
For additional help on any menu, click Help at the top of the screen.
To change router settings:
Open Linksys Smart Wi-Fi and log in to your account.
In the menu on the left, click an option:
Device List lets you display and manage all network devices connected to your router. You can view devices on your main
network and your guest network, disconnect the devices, or display information about each device.
Guest Access lets you configure a network so guests can access the Internet, but not all of your network resources.
Parental Controls let you block web sites and set Internet access times.
Media Prioritization lets you set which devices and applications have top priority for your network traffic.
Speed Test lets you test your network’s Internet connection speed.
USB Storage lets you access an attached USB drive (not included) and set up file sharing, a media server, and FTP access.
(Available only on routers with USB ports.)
Connectivity lets you configure basic and advanced network settings.
Troubleshooting lets you diagnose problems with your router and check the status of the network.
Wireless lets you configure your router’s wireless network. You can change the security mode, password, MAC filtering, and
connect devices using Wi-Fi Protected Setup™.
Security lets you configure your router’s wireless security. You can set up the firewall, VPN settings, and make custom settings
for applications and games.
Troubleshooting
This chapter can help you solve common setup issues and connect to the Internet. You can find more help from our award-winning
customer support at
linksys.com/support.
Your router was not successfully set up
If Linksys Smart Wi-Fi i not complete the setup, you can try the following:
Press and hold the Reset button on your router with a paperclip or pin until the LED starts flashing (about 10 seconds), then
install the router again.
Your router’s appearance may vary
Temporarily disable your computer’s firewall (see the security software’s instructions for help), and install the router again.
If you have another computer, use that computer to install the router again.
Windows XP Service Pack update
On Windows XP computers, Linksys Smart Wi-Fi requires Service Pack 3. If the currently installed Service Pack is older than version
3, you need to download and install Service Pack 3.
TIP
To temporarily connect to the Internet and download the required
Service Pack, you can use the included Ethernet cable to connect
your computer directly to your modem.
To install Service Pack 3:
Connect to the Microsoft Update website (up ate.microsoft.com/win owsup ate).
Follow the instructions on the website or contact Microsoft if you need further help.
After downloading and installing Service Pack 3, install the router again.
Your Internet cable is not plugged in message
If you get a “Your Internet cable is not plugged in” message when trying to set up your router, follow these troubleshooting steps.
To fix the problem:
Make sure that an Ethernet or Internet cable (or a cable like the one supplied with your router) is securely connected to the yellow
Internet port on the back of the router and to the appropriate port on your modem. This port on the modem is usually labeled
Ethernet, but may be named Internet or WAN.
Back view of router
Back view of cable modem
Back view of DSL modem
Make sure that your modem is connected to power and is turned on. If it has a power switch, make sure that it is set to the ON
or lposition.
If your Internet service is cable, verify that the cable modem’s CABLE port is connected to the coaxial cable provided by your ISP.
Or, if your Internet service is DSL, make sure that the DSL phone line is connected to the modem’s DSL port.
If your computer was previously connected to your modem with a USB cable, disconnect the USB cable.
Install the router again.
Cannot access your router message
If you cannot access your router because your computer is not connected to your network, follow these troubleshooting steps.
To access your router, you must be connected to your own network. If you currently have wireless Internet access, the problem may
be that you have accidentally connected to a different wireless network.
To fix the problem on Win ows computers:
On your Windows desktop, right-click the wireless icon in the system tray. The icon can differ depending on your version of
Windows.
Tabla de contenidos
Otros manuales de Enrutador inalámbrico de Linksys
Linksys
Linksys Linksys E1200 Manual de usuario
Linksys
Linksys E2500 Manual de usuario
Linksys
Linksys WUSB54GS EU Manual de operación
Linksys
Linksys EA6350 Manual de usuario
Linksys
Linksys Small Business WRP400 Instrucciones de funcionamiento originales
Linksys
Linksys WRT54G3GV2-ST - Wireless-G Router For Mobile Broadband... Manual de usuario
Linksys
Linksys MAX-STREAM MR9600 Manual de usuario
Linksys
Linksys WRT 1200 ac Manual de usuario
Linksys
Linksys WRT54G3G - Wireless-G Router For Verizon Wireless... Manual de usuario
Linksys
Linksys WRT330N - Wireless-N Gigabit Gaming Router... Instrucciones de funcionamiento originales
Linksys
Linksys WRT54GL - Wireless-G Broadband Router... Manual de usuario
Linksys
Linksys WRT54G3G-ST Manual de usuario
Linksys
Linksys BEFW11S4-AT Manual de usuario
Linksys
Linksys WRV200 Manual de usuario
Linksys
Linksys WRT54GS Manual de usuario
Linksys
Linksys WRT 1900AC Manual de usuario
Linksys
Linksys WRT54GX - Wireless-G Broadband Router Manual de usuario
Linksys
Linksys EA6100 Manual de usuario
Linksys
Linksys WRTU54G-TM Manual de usuario
Linksys
Linksys MAX-STREAM MR5500 Series Manual de usuario
