Linksys WRK54G Manual de usuario
A Division of Cisco Systems, Inc.
®
Model No.
Wireless
1
Quick Installation Guide
WRK54G (EU/LA/UK)
Broadband Router
Wireless-G
Package Contents*
• Wireless-G Broadband Router
• Setup CD-ROM (with Symantec
Internet Security)
• User Guide on CD-ROM (English
Only)
• Power Adapter
• Ethernet Network Cable
• Quick Installation Guide
*other items may be included
GHz
2
802.11g
4
,
2
1
ABefore you begin, make sure
that you have the setup
information for your specific
type of Internet connection.
The installation technician from
your ISP should have left this
information with you after
installing your broadband
connection. If not, you can call
your ISP to request the settings.
BMake sure that all of your
network’s hardware is powered
off, including the Router, PCs,
and cable or DSL modem.
CConnect one end of an
Ethernet network cable to one
of the ports (labeled 1-4) on
the back of the Router, and the
other end to an Ethernet port
on a PC.
DRepeat step C to connect
additional PCs or other network
devices to the Router.
Connect the Broadband Router
C
3
EConnect a different Ethernet
network cable from your cable
or DSL modem to the Internet
port on the Router’s back
panel. This is the only port that
will work for your modem
connection.
FPower on the cable or DSL
modem.
GConnect the AC power
adapter to the Router’s Power
port and the other end into an
electrical outlet.
HMake sure the Power and
Internet LEDs on the front panel
light up green.
IThe Power LED will flash green
for a few seconds when the
Router goes through its self-
diagnostic test. This LED will stay
solidly lit when the self-test is
complete. If it does not stop
flashing, refer to “Appendix A:
Troubleshooting” in the Router’s
User Guide on the Setup CD-
ROM.
JPower on the PC you wish to
use to configure the Router.
Proceed to Step 2.
IMPORTANT: Make sure you use
the power adapter that is supplied
with the Router. Use of a different
power adapter could damage the
Router.
G
E
4
2
These instructions will show you how
to configure the Router. You only
need to configure it once.
AOpen your web browser. Enter
http://192.168.1.1 in its
Address field. Press the Enter
key.
BA password request screen will
appear. Leave the User Name
field empty, and enter the
default password, admin, in
lowercase letters in the
Password field. (You should
later set a new password,
using the Administration tab’s
Management screen of the
Web-based Utility). Then, click
the OK button.
CThe Web-based Utility will
appear with the Setup tab
selected. If requested by your
ISP (usually cable ISPs),
complete the Host Name and
Domain Name fields.
Otherwise, leave them blank.
DFor the Internet Connection
Type setting, six connection
types are offered through the
drop-down menu. Each Setup
screen and available features
will differ depending on which
connection type you select. C
NOTE: Make sure your PC’s Ethernet
adapter is set to obtain an IP address
automatically. For more information,
refer to Windows Help.
A
Configure the Broadband Router
B
5
Internet Configuration Type
DHCP: If you are connecting
through DHCP or a dynamic IP
address from your ISP, keep the
default setting Obtain an IP
automatically.
Static IP: If your ISP assigns you a
static IP address, select Static IP
from the drop-down menu.
Complete the Internet IP
Address, Subnet Mask, Gateway,
and Static DNS fields. You need
to enter at least one DNS
address.
PPPoE: If you are connecting
through PPPoE, select PPPoE from
the drop-down menu. Complete
the User Name and Password
fields. Select Keep Alive if you
always want to be connected to
your ISP, or select Connect on
Demand if you are charged for
the time that you are connected
to your ISP.
L2TP: L2TP is a service used in Israel
only. If you are using an L2TP
connection, check with your ISP
for setup information.
PPTP: PPTP is a service used in
Europe only. If you are using a
PPTP connection, select PPTP
from the drop-down menu.
Complete the IP Address, Subnet
Mask, Default Gateway, User
Name ,and Password fields.
Select Keep Alive
if you always
DHCP
Static IP
PPPoE
L2TP
PPTP
6
want to be connected to your ISP,
or select Connect on Demand if
you are charged for the time that
you are connected to your ISP.
Telstra: Telstra (HeartBeat Signal)
is a service used in Australia only. If
you are using a HeartBeat Signal
connection, check with your ISP for
setup information.
EWhen you have finished
entering your Internet
connection settings, click the
Save Settings button to save
your changes.
FTo configure the Router for your
wireless network, select the
Wireless Tab’s Basic Wireless
Settings screen.
GWireless Network Mode.
Select the mode you are using
from the drop-down menu: If
you are using only 802.11g,
select G-Only; if you’re using
802.11b only, select B-Only; if
you’re using both 802.11b and
802.11g, keep Mixed setting.
HWireless Network Name (SSID).
The SSID is the network name
shared among all devices in a
wireless network. The SSID must
be identical for all devices in
the wireless network. It is case-
sensitive and must not exceed
32 characters (use any
keyboard character). For
F
Telstra
7
added security, you should
change the default SSID linksys
to a unique name.
IWireless Channel. Select the
appropriate channel from the
list provided to correspond with
your network settings. All
devices in your wireless network
must broadcast on the same
channel in order to function
correctly.
JWireless SSID Broadcast. When
wireless clients survey the local
area for wireless networks to
associate with, they will detect
the SSID broadcast by the
Router. To broadcast the
Router's SSID, keep the default
setting, Enable. If you do not
want to broadcast the Router's
SSID, then select Disable.
KChange these settings as
described here and click the
Save Settings button to apply
your changes.
LPower your modem off and
back on again.
MRestart your computer.
NTest the setup by opening your
web browser and entering
http://www.linksys.com/
registration
.
The installation of the Wireless-G
Broadband Router is complete.
N
NOTE: For more advanced settings
and security options, refer to the
User Guide on the Router’s CD-ROM.
IMPORTANT: Once the Router is
configured, wireless security,
either WEP or WPA, should be
configured to prevent security
breaches in your network.
3
The Router comes equipped with
four types of wireless security: WEP,
WPA Pre-Shared, WPA Enterprise, and
RADIUS. These security methods are
not enabled right out of the box,
however. To configure wireless
security on the Router, do the
following:
AOpen the Router’s Web Utility
as shown in Step 2, and click
the Wireless tab. The Basic
Wireless Settings screen will
appear.
BSelect Wireless Security to
configure wireless security on
the Router.
Directions for the configuration
of WEP and WPA Pre-Shared
wireless security are provided
here.
CFrom the Security Mode pull-
down menu, select the type of
wireless security you’ll use on
your network.
WEP: WEP is a basic encryption
method, which is not as secure as
WPA. To use WEP, select a Default
Transmit Key (choose which Key to
use), and a level of WEP
encryption, 64 bits 10 hex digits
or 128 bits 26 hex digits. Then
either generate a WEP key using
the Passphrase or enter the WEP
key manually.
Configuring Wireless Security
NOTE: If your wireless adapters
support Secure Easy Setup (SES), you
can use the SES button on the Router
to set up wireless security.
Basic Wireless Settings
NOTE: Please refer to the User Guide
if you wish to configure WPA Enterpise
or RADIUS wireless security options.
WEP Security Settings
WPA Pre-Shared: WPA gives you
two encryption methods, TKIP and
AES, with dynamic encryption keys.
Select the type of algorithm, TKIP
or AES. Enter a WPA Shared Key of
8-63 characters. Then enter a
Group Key Renewal period, which
instructs the Router how often it
should change the encryption
keys.
DClick the Save Settings button.
Congratulations! Wireless Security
is now configured on the Router.
WRK54G-EU-LA-UK_V2-QIG-51114 TE
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2005
Cisco Systems, Inc. All rights reserved.
For additional information or troubleshooting
help, refer to the User Guide on the CD-ROM
or the Technical Support Insert. You can also
e-mail for further support.
Website
http://www.linksys.com/international
Product Registration
http://www.linksys.com/registration
WPA Pre-Shared
Security Settings
A Division of Cisco Systems, Inc.
®
Modelnr.
Wireless
1
Installationsvejledning
WRK54G (DK)
Bredbånds-router
Trådløs-G
Pakkens indhold*
• Trådløs-G Bredbånds-router
• Installations-cd-rom (med Symantec
Internet Security)
• Brugervejledning på cd-rom (kun på
engelsk)
• Strømforsyning
• Ethernet-kabel
• Installationsvejledning
*andre dele kan være vedlagt
GHz
2802.11g
4
,
Otros manuales para WRK54G
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Enrutador de red de Linksys
Linksys
Linksys Velop WHW01 Manual de usuario
Linksys
Linksys EF1324 Manual de usuario
Linksys
Linksys SGE2010P Manual de operación
Linksys
Linksys EA6350 Instrucciones de funcionamiento y seguridad
Linksys
Linksys EA8500-EU Manual de usuario
Linksys
Linksys RVS4000 Manual de usuario
Linksys
Linksys WRT54G - Wireless-G Broadband Router... Manual de usuario
Linksys
Linksys WET11 - Instant Wireless EN Bridge Network... Manual de usuario
Linksys
Linksys LRT214 Manual de usuario
Linksys
Linksys EF3512 - EtherFast Gigabit Ethernet Switch Manual de usuario
Linksys
Linksys WET54G V3 Manual de usuario
Linksys
Linksys SRW2008 Manual de usuario
Linksys
Linksys BEFSX41 - Instant Broadband EtherFast Cable/DSL Firewall... Manual de usuario
Linksys
Linksys BEFSX41 - Instant Broadband EtherFast Cable/DSL Firewall... Manual de usuario
Linksys
Linksys BEFN2PS4 - EtherFast Cable/DSL And Voice... Manual de usuario
Linksys
Linksys HPRO200 Manual de usuario
Linksys
Linksys MAX-STREAM Manual de usuario
Linksys
Linksys FGW5500 Manual de usuario
Linksys
Linksys EA8500 Manual de usuario
Linksys
Linksys WRT54GH Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad