Linear Technology LTC3805/-5 Manual de usuario

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 1311

TELECOM DC/DC CONVERTER

LTC3805/-5

DESCRIPTION

Demonstration circuit 1311 is a Telecom isolated

DC/DC converter featuring the LTC3805/-5 constant

frequency current mode flyback controller. The

DC1311 converts 18V to 72V input voltage to an

isolated 3A of output current at 3.3V. The 300kHz

constant frequency operation is maintained down to

very light load to reduce low frequency noise

generated over a wide range of load current. The

converter provides high output voltage accuracy

(typically ±2%) over wide load range with no

minimum load requirement.

The DC1311 also provides non-isolated design by

removing opto coupler and LTC4430 circuit. The

demonstration circuit can be easily modified to

generate different output voltages up to 15V. As

output voltage is increased, the maximum

output current must be reduced to limit the

output power to no more than 10W. Higher

output voltages and currents can be achieved by

changing the MOSFET, transformer and output

capacitors. Please consult LTC factory for details.

The DC1311 has a small circuit footprint. It is a high

performance and cost effective solution for Telecom,

Automotive and Power over Ethernet applications.

Design files for this circuit board are available. Call

the LTC factory.

LTC and LT are registered trademarks of Linear Technology Corporation.

QUICK START PROCEDURE

Demonstration circuit 1311 is easy to set up to

evaluate the performance of the LTC3805/-5. For

proper measurement equipment setup refer to

Figure 1 and follow the procedure below.

When measuring the input or output voltage ripple,

care must be taken to minimize the length of the

oscilloscope probe ground lead. Measure the input or

output voltage ripple by connecting the probe tip

directly across the V

or V

OUT

and GND terminals,

see Figure 2.

With power off, connect the input power supply to

+Vin and -Vin.

Move the J1 (RUN) switch to ON position.

Turn the input power source on and slowly

increase the input voltage. Be careful not to exceed

72V. Make sure that the input voltage V

does not

exceed 72V. If higher operating voltage is required,

power components with higher voltage ratings

should be used.

Check for proper output voltage. Vout=3.3V.

If there is no output, temporarily disconnect the

load to make sure that the load is not set too high.

To shut the converter down, move the RUN switch

into OFF position

To synchronize converter to external clock, set

jumper JP2 (SYNC) to ‘EXT’ position, apply signal

to FSET pin. See LTC3805/-5 datasheet for

synchronization signal parameters.

Once the proper output voltage is established,

adjust the load within 3.0A range and observe the

output voltage regulation, ripple voltage, efficiency

and other parameters.

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 1311

TELECOM DC/DC CONVERTER

Figure 1. Proper Measurement Equipment Setup

Figure 2. Measuring Input or Output Ripple

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 1311

TELECOM DC/DC CONVERTER

Otros manuales de Controladores de Linear Technology

Linear Technology

Linear Technology DC1663A Guía de configuración rápida

Linear Technology

Linear Technology DC1084A-B Manual de usuario

Linear Technology

Linear Technology LTC3703-5 Manual de usuario

Linear Technology

Linear Technology DC2453A Guía de configuración rápida

Linear Technology

Linear Technology LTC2920-1CS5 Manual de usuario

Linear Technology

Linear Technology 1158A Manual de usuario

Linear Technology

Linear Technology LT3507A Guía de configuración rápida

Linear Technology

Linear Technology DC2007A-B Guía de configuración rápida

Linear Technology

Linear Technology LTM4650-1 Guía de configuración rápida

Linear Technology

Linear Technology LTM8003 Guía de configuración rápida

Linear Technology

Linear Technology LTM4677EY Guía de configuración rápida

Linear Technology

Linear Technology LT8609 Manual de usuario

Linear Technology

Linear Technology LTM4620A Guía de configuración rápida

Linear Technology

Linear Technology LT3091EDE Guía de configuración rápida

Linear Technology

Linear Technology LTC3618EUF Guía de configuración rápida

Linear Technology

Linear Technology DC2087A Guía de configuración rápida

Linear Technology

Linear Technology LT3755 Manual de usuario

Linear Technology

Linear Technology DC1865A Guía de configuración rápida

Linear Technology

Linear Technology 813 Instrucciones de funcionamiento y mantenimiento

Linear Technology

Linear Technology LINEARCOM3000 LC3.IRTX Manual de usuario

Linear Technology

Linear Technology LTC4266A Manual de usuario

Linear Technology

Linear Technology 824 Manual de usuario

Linear Technology

Linear Technology DC1831A Manual de usuario

Linear Technology

Linear Technology LTM4645 Guía de configuración rápida

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario