Lincat OE8306 Manual del propietario

IS 609 ECN 3977 Page 1 of 9

Installation, Operating and Servicing

Instructions

Opus 800 Electric Cook & Hold Salamander

OE8306

Please make a note of your product details for

future use:

Date Purchased:_________________________

Model Number:__________________________

Serial Number:__________________________

Dealer:_________________________________

_______________________________________

IS 609 ECN 3977 Page 2 of 9

CONTENTS

Important Information

Warnings and Precautions

Technical Data

Checklist of Enclosures

Installation and Commissioning

4-5

Operating Instructions

6-7

Cleaning

Servicing, Maintenance and Component Replacement

7-9

Fault Finding

Spare Parts List

Accessories

Service Information and Guarantee

IMPORTANT INFORMATION

Read these instructions carefully before using this product, paying particular

attention to all sections that carry warning symbols, caution symbols and notices.

Ensure that these are understood at all times.

WARNING!

This symbol is used whenever there is a risk of personal injury.

CAUTION!

This symbol is used whenever there is a risk of damaging your Lincat product.

NOTE:

This symbol is used to provide additional information, hints and tips.

KEEP THIS MANUAL FOR FUTURE REFERENCE

IS 609 ECN 3977 Page 3 of 9

WARNINGS AND PRECAUTIONS

This appliance must be installed, commissioned and serviced by a qualified person

in accordance with national and local regulations in force in the country of

installation.

If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified person.

Ensure that the plug/socket is accessible at all times.

Strip plastic coating and clean the appliance before use.

During operation parts may become hot - avoid accidental contact.

Disconnect this appliance before servicing, maintenance or cleaning.

TECHNICAL DATA

Height (mm)

510

Width (mm)

600

Depth (mm)

520

Weight (kg)

Cooking area w x d (mm)

530 x 340

Number of individually controlled heat zones

Heat input per element (watts)

1500

Total heat input (kW)

4.5

Electricity supply 1N~+e 230V 50-60Hz

Current Rating (Amps)

19.6

Electricity supply 3N~+e 400V 50-60Hz

Current Rating (Amps)

L1 –6.5

L2 –6.5

L3 –6.5

*NB. Appliances are 600mm deep when wall mounted.

CHECK LIST OF ENCLOSURES

Warranty card

Instructions manual

Collection tray

Chrome plated grilling rack

Wire tray

Heat shield

IS 609 ECN 3977 Page 4 of 9

INSTALLATION AND COMMISSIONING

This product is heavy; prior to installation a handling assessment should be made.

This appliance must be earthed. An equipotential bonding terminal is provided to

allow cross bonding with other equipment.

Means of isolation with at least 3mm contact separation in all poles must be

incorporated into the fixed wiring of this appliance.

The fixed wiring insulation must be protected by insulated sleeving having a

temperature rating of at least 60 Deg C.

Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary

polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57).

This appliance may be counter or wall mounted. For either installation, remove and

discard the 2 transportation screws (A) from rear panel (Fig 2).

Install this appliance on a level surface ensuring all vents are unobstructed. Any

partitions, walls or furniture must be of non-combustible material (see Fig 2).

Minimum distances A 300mm B 500mm.

Do not install above any heat source the unit vents from the underside and this

could cause the unit too over heat.

Warning: During installation do not place on surfaces or near walls, partitions or

kitchen furniture and a like –unless they are made of non-combustible material or

clad with non-combustible heating-insulating material, and pay attention to fire

prevention regulations.

Electrical connection

The electrical supply cable enters the unit through a cable gland in the rear panel

with access via a removable side panel(see Fig 1).

Connection of the electrical supply cable is to a terminal block behind the side

panel. Open the protective cover on the terminal housing where indicated using a

flat bladed screwdriver. Fit a suitable cable into the strain relief and then to the

terminal block.

Fig 1

IS 609 ECN 3977 Page 5 of 9

Fig 2

IS 609 ECN 3977 Page 6 of 9

OPERATING INSTRUCTIONS

Electronic display and control

A B C D E

F G H I

Fig 2

A On/Off Button –Left Heating Element

BOn/Off Button –Centre Heating Element

COn/Off Button –Right Heating Element

D Digital Display

EOn/Off isolating switch

FCook/Hold Function Button (cycles through Cook –Hold –Cook and Hold)

GStart/Stop Key

HControl for setting either time and hold level setting

ITimer 0-20mins / Hold setting 1-6 Encoder Knob

Only qualified or trained personnel should use this appliance.

This appliance has 3 cooking modes Cook –Hold –Cook & Hold these are

indicated with the illumination of the LED on button (F)

(The switching between the different cooking modes is allowed only in stop)

Cook Hold Cook & Hold

Switching on

After turning on the unit it will always remember the last setting used.

Cook

Select the cook mode F.

Select heating element On/Off A/B/C.

Adjust height of the hood to desired position.

Cycle time required 0-20mins I.

Start the unit Gor activate the plate detection.

(The LED will flash during the cooking cycle)

Note: At cycle end the buzzer will sound and “End” is displayed.

IS 609 ECN 3977 Page 7 of 9

Hold

Select the hold mode F.

Select heating element On/Off A/B/C.

Adjust height of the hood to desired position.

Select the hold level from level 1 to 6 I.

Start the unit Gor activate the plate detection.

(The LED will flash during hold activation)

Note: The hold mode has no end time, it works until the stop key is pressed.

Cook & Hold

Select the cook & hold mode F.

Select heating element On/Off A/B/C.

Adjust height of the hood to desired position.

Cook cycle time required 0-20mins I.

Hold setting will be the same as last used. (Adjust if necessary before start or during hold)

Start the unit Gor activate the plate detection.

(The LED will flash when cook or hold is in start)

Note: At cook cycle end the buzzer will sound, the unit will automatically start the

hold mode.

The power configuration, time and hold mode settings can be adjusted anytime

during operation. The unit will always remember the last settings used. When

cooking is ended “End” is displayed.

After 60sec of inactivity the display will show OPUS 800. Input on the keyboard or

encoder the display turns to normal state.

Shutting down

Turn the control knob to the ‘Off’ position and switch off at the isolating socket.

Be aware that the appliance will remain hot for some time.

CLEANING

Your Lincat product has a manufacturer’s warranty. This requires you to maintain

and care for your product and follow maintenance instructions. If you fail to maintain

your unit or damage components Lincat may charge you for a warranty repair.

Please check the website for terms and conditions.

Do not use a water jet or steam cleaner, and do not immerse this appliance.

Clean all panels with warm water and mild detergent, do not use abrasive materials

or cleaners containing chlorine. Dry with a soft cloth.

IS 609 ECN 3977 Page 8 of 9

SERVICING, MAINTENANCE AND

COMPONENT REPLACEMENT

All servicing, maintenance and component replacement on this appliance should be

carried out by one of our recommended service engineers.

Please refer to the Service Help Desk number on the final page of this manual.

Heat sink overheat

If the over temperature is reached the heating is disabled and a blinking label “Hot”

is displayed. The alarm is automatically reset when the temp falls below 5˚C below

this level.

Probe Failure

There is a label “St1” blinking if:

Temperature measured from ST1 is out of range.

Short circuit is recognized on analog input ST1

Open circuit is recognized on analog input ST1

Please inform the Lincat service desk when you call.

Part Number

Description

EL309

Element

EN02

Encoder

FI43

Noise Filter

FU25

Fuse

GL658

Glass

KN251

Control knob

PR01

PCBA Salamander

PR02

TRIAC Board

PR04

Electronic Cable PR02

SS11

Straps

SW100

Multi Function Switch

SW101

Multi Function Switch

TR03

Transformer

X52800

Micro switch

Part Number

Description

BR75

Wall bracket

FAULT FINDING

SPARE PARTS LIST

ACCESSORIES

IS 609 ECN 3977 Page 9 of 9

For help with the installation, maintenance and use of your Lincat equipment,

please contact our service department:

UK: 01522 875520

For non-UK customers, please contact your local Lincat dealer

All service work, other than routine cleaning should be carried out by one of our

authorised service agents. We cannot accept responsibility for work carried out by

other persons.

To ensure your service enquiry is handled as efficiently as possible, please tell us:

Brief details of the problem

Product code

All available on serial plate

Type number

Serial number

Lincat reserve the right to carry out any work under warranty, given reasonable

access to the appliance, during normal working hours, Monday to Friday, 08:30 to

17:00.

GUARANTEE

This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is

in addition to, and does not diminish your statutory or legal rights.

The guarantee does not cover:

Accidental damage, misuse or use not in accordance with the manufacturer’s

instructions

Consumable items (such as filters, glass, bulbs, slot toaster elements and door

seals.)

Damage due to incorrect installation, modification, unauthorised service work or

damage due to scale, food debris build-up, etc.

The manufacturer disclaims any liability for incidental, or consequential damages.

Attendance is based on reasonable access to the appliance to allow the authorised

technician to carry out the warranty work.

SERVICE INFORMATION

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Parrilla de Lincat

Lincat

Lincat Lynx 400 GG1R Manual del propietario

Lincat

Lincat Opus 700 Series Instrucciones de funcionamiento

Lincat

Lincat Opus 800 Series Guía del usuario

Lincat

Lincat Opus 700 Series Manual de usuario

Lincat

Lincat Silverlink 600 Instrucciones de funcionamiento

Lincat

Lincat Silverlink 600 Manual

Lincat

Lincat OG7302 Guía de solución de problemas

Lincat

Lincat Opus 800 Salamander OG8301 Guía del usuario

Lincat

Lincat OG7402 Manual de usuario

Lincat

Lincat Lynx 400 Instrucciones de funcionamiento

Lincat

Lincat Phoenix Salamander PHEAS01 Manual del propietario

Lincat

Lincat LCG Instrucciones de funcionamiento

Lincat

Lincat GR3 Guía de solución de problemas

Lincat

Lincat Silverlink 600 ECG6 Manual del propietario

Lincat

Lincat Silverlink 600 CG4 Manual

Lincat

Lincat Opus 800 OG8410-A001 Manual de usuario

Lincat

Lincat OE8405 Manual del propietario

Lincat

Lincat Silverlink 600 GR3 Manual del propietario

Lincat

Lincat Lynx 400 Instrucciones de funcionamiento

Lincat

Lincat Lynx 400 LSC Guía

Lincat

Lincat OG7401 Manual de usuario

Lincat

Lincat Opus 800 OE8413 Manual del propietario

Lincat

Lincat OE7303 Manual de usuario

Lincat

Lincat Silverlink 600 Series Manual

Manuales populares de Parrilla de otras marcas

Orbegozo

Orbegozo GR 2300 Manual de usuario

bora

bora PT11 Manual de usuario

Klarstein

Klarstein 10031664 Manual de usuario

Garland

Garland MWE3W Manual de usuario

Char-Broil

Char-Broil 463722714 Manual de usuario

Nexgrill

Nexgrill 720-0830HK Manual de usuario

Kenmore

Kenmore 415.16123800 Manual de usuario

Camp Chef

Camp Chef PG24CLAU Manual de usuario

Tucker Barbecues

Tucker Barbecues GTR Series Instrucciones de montaje

Monogram

Monogram ZGG540NCP1SS Manual de usuario

Equipex

Equipex Sodir Savoy Manual de usuario

Gaggenau

Gaggenau VR 414 610 Manual de usuario

Miele

Miele KM 408-1 Manual de usuario

George Foreman

George Foreman GGR50B Manual de usuario

AOG

AOG T series Manual de usuario

Gorenje

Gorenje TG2000CB Manual de instrucciones

Weber

Weber Genesis Silver-B Permamount NG 051701 Manual de usuario

Glen

Glen SA 3037 Manual de usuario