Lilliput Q17 Manual de usuario
1
Contents
Precaution................................................................................................................................2
1. Main Features.....................................................................................................................3
2. Product Description..........................................................................................................4
2.1 Front Panel..................................................................................................................4
2.2 Rear Panel.......................................................................................................................5
3. Menu Setting.......................................................................................................................8
3.1 Short Key........................................................................................................................8
3.1.1 Menu Knob.................................................................................................................8
3.1.2 F1-F2 Buttons.............................................................................................................8
3.2 Menu Operations...........................................................................................................9
3.2.1 PICTURE....................................................................................................................9
3.2.2 MARKER...................................................................................................................12
3.2.3 FUNCTION.................................................................................................................13
3.2.4 WAVEFORM..............................................................................................................15
3.2.5 AUDIO.......................................................................................................................18
3.2.6 REMOTE...................................................................................................................20
3.2.7 SYSTEM.....................................................................................................................23
4. Product Parameters..........................................................................................................26
5. Accessories.........................................................................................................................27
6. Trouble Shooting...............................................................................................................28
Appendix: 3D LUT Loading & RemoteTerminal Instructions.................................................29
2
Important Safety Instructions:
Please read User Guide before using this product.
Please keep User Guide for future reference.
Please read the precaution to prevent possible danger and loss of property.
Precaution:
Please do not place the display screen towards the ground.
Please avoid heavy impact or drop onto the ground.
Please do not use chemical solutions to clean this product. Please wipe with a clean soft cloth to
maintain the brightness of the surface.
Please do not block any vent hole.
Please follow the instructions and trouble-shootings to adjust the product. Other improper adjustment
may result in damage. Any further adjustment must be performed or conducted by a qualified
technician.
Please unplug the power and remove the battery if long-term no-use, or thunder weather.
3
1. Main Features
Support standard 12G-SDI input interface (x2), 3G-SDI input interface (x2), and support Single-Link,
Dual-Link and Quad-Link signals.
Support HDMI 2.0/1.4 inputs and loop outputs.
Support SFP optical Connector input, optical module for optional.
Loop output signals support up to 3840x2160 23.98/24/25/29.97/30/50/59.94/60p and 4096x2160
23.98/24/25/29.97/30/47.95/48/50/59.94/60p.
Monitor control via LAN, GPI, RS422.
Customized Menu Knob.
Support customized various waveform mode: Waveform/Vector/Histogram/4 Bar Display/Audio
Vector/Level Meter.
HDR (High Dynamic Range) display supporting ST 2084 and Hybrid Log Gamma.
Gamma selection: 1.8-2.8.
Custom 3D LUT file load through USB.
Wide color space supporting SMPTE-C, Rec709, EBU and Native.
Color Space/ HDR/Gamma /Camera Log comparison with original (side by side).
Color Temperature: 3200K/5500K/6500K/7500K/9300K/User.
False Color: Default/Spectrum/ARRI/RED.
Aspect Marker (16:9/1.85:1/2.35:1/4:3/2.0X/2.0X MAG/Grid/User).
Aspect (Full/16:9/1.85:1/2.35:1/4:3/3:2/2.0X/2.0X MAG).
Audio: supporting Audio Phase and Level Meter, HDMI supporting 8 channels, and SDI supporting 16
channels.
TimeCode: LTC/VITC.
UMD display:White/Red/Green/Blue/Yellow/Cyan/Magenta text color for optional.
Color Bar Mode: Rec601/Rec709/BT2020.
Check Field: Red/Green/Blue/Mono.
Zoom at any position and at different scale.
Peaking (Red/Green/Blue/White/Black).
Tally (Red/Green/Yellow).
4
2. Production Description
2.1 Front Panel
1) SDI Buttons
- Single Button/Lamp: SDI1/SDI2/SDI3/SDI4/SFP signal input.
- 2SI Button/Lamp
- Square Button/Lamp
2) HDMI Button/Lamp
3) F1/F2 Button/Lamp
Assigned function by factory as follow:
- [F1]: Waveform
- [F2]: Color Space
4) Exit Button
5) Menu Knob
6) USB (For 3D LUT load and software update)
7) Earphone Jack
5
2.2 Rear Panel
2.2.1 Interfaces
1) 4pin power input for V-mount/Anton Bauer mount battery plate.
2) Power Switch: “O” is power off, “II” is battery power supply, “I” is DC power supply.
3) Power IN: 4-pin XLR DC.
4) SFP Input
5) HDMI 2.0 Input
6) HDMI 2.0 Output
7) SDI Input
- 12G-SDI Input *2
- 3G-SDI Input *2
8) SDI Output
- 12G-SDI Output *2
- 3G-SDI Output *2
9) GPI Input (RJ45, 8-pin): See Page22 GPI 1-8.
10) RS422 Input (RJ45, 8-pin): Supporting the default and TSL V3.1 protocols to control Monitor.
Follow this instructions about this port.
6
PIN Number
Instruction
PIN 1
Y
PIN 2
Z
PIN 3
A
PIN 4
NC
PIN 5
NC
PIN 6
B
PIN 7
NC
PIN 8
GND
11) RS422 Output (RJ45, 8-pin): Supporting the default and TSL V3.1 protocols to control Monitor. The
instructions about the port is as above.
12) LAN (10/100) Input (RJ45): Supporting the default protocol to control Monitor.
Note: The "RemoteTerminal.exe" as default protocol to control Monitor.
2.2.2 Standard VESA
Standard 75mm*75mm is used for external battery (V-mount/Anton Bauer mount battery).
Standard 75mm*75mm and 100mm*100mm, can be used for external hanging bracket.
7
Process of Installing Battery Plate:
- Install the plate base before installing the battery plate.
- Standard with V-mount battery plate: Referring to the following pictures for installation process and
GP-L130AB type battery.
- Optional Anton Bauer battery plate. Referring to the following pictures for installation process and
GP-L130B type battery.
8
3. Menu Setting
Before setting the functions, please make sure the device is connected correctly.
3.1 Shortcut keys
3.1.1 Menu Knob
Power on the monitor, press Menu Knob to display OSD, and select options as the following sequence
via rotating it: PICTURE/MARKER/FUNCTION/WAVEFORM/AUDIO/REMOTE/SYSTEM.
Press Menu Knob to enter the desired function, rotate it to change the value/option, and press Menu
Knob or Exit again to confirm the changes.
Functions of Menu Knob can be customized: [Back Light], [Brightness], [Contrast], [Saturation], [Tint],
[Sharpness], [Volume], [Peaking Level]. After setting the Knob’s customized function, rotating it can
display the function, and rotating it again can adjust the value. Press it to switch to the next option in
turn. Default option: [Back Light].
3.1.2 F1-F2 Buttons:
Long press any F1-F2 buttons for 3-5 seconds to pop up shortcut menu on the
screen. As shown in Figure. Select option via rotating the Menu Knob, and set it as
default via pressing the Knob, then press Exit button to exit shortcut setting menu.
The customized function will be remembered by F1/F2 buttons.
Functions of F1-F2 buttons can also be customized: [Center Marker], [Aspect
Marker], [Safety Marker], [Overscan], [Scan], [Aspect], [Color Space], [Gamma],
[Camera Log], [Check Field], [H/V Delay], [Freeze], [Image Flip], [Color Bar],,
[Peaking], [False Color], [Exposure], [Histogram], [Waveform], [TimeCode], [Mute],
[Level Meter], and [Audio Vector].
Default function: F1: [Waveform] F2: [Color Space].
9
3.2 MENU Operation
3.2.1 PICTURE
SDI Mode HDMI Mode
Brightness
Control the degree of brightness between 0-100.
Contrast
Control contrast ratio between 0-100.
Saturation
Adjust the color intensity between 0-100.
Tint
Adjust tint between 0-100.
Sharpness
Control sharpness of the image between 0-100.
HDMI RGB Range
Use this item to choose one of the HDMI RGB Range presets: [Full], [Limited].
HDMI EDID
Select the HDMI EDID from between [4K] and [2K]. This item enables PC or other devices to recognize
the property of this monitor and makes the images look excellent on the screen.
Color Space
Tabla de contenidos
Otros manuales de Monitor de Lilliput
Lilliput
Lilliput BM280-4K Manual de usuario
Lilliput
Lilliput FA1014 Manual de usuario
Lilliput
Lilliput A7S Manual de usuario
Lilliput
Lilliput 665WH Manual de usuario
Lilliput
Lilliput RM-503S Manual de usuario
Lilliput
Lilliput 5DII Manual de usuario
Lilliput
Lilliput A12 Manual de usuario
Lilliput
Lilliput 569-O/P Manual de usuario
Lilliput
Lilliput 668GL-70NP/H/Y Manual de usuario
Lilliput
Lilliput Mopro 7 Manual de usuario
Lilliput
Lilliput FA1019/T Manual de usuario
Lilliput
Lilliput A11 Manual de usuario
Lilliput
Lilliput TK701 Manual de usuario
Lilliput
Lilliput FA1000 Manual de usuario
Lilliput
Lilliput FA1045 Manual de usuario
Lilliput
Lilliput PVM210 Manual de usuario
Lilliput
Lilliput Q7 Manual de usuario
Lilliput
Lilliput 869GL Manual de usuario
Lilliput
Lilliput 663/O/P2 Manual de usuario
Lilliput
Lilliput 664W Manual de usuario
