LG LVC-SX811HM Manual de usuario

LG Video Camera

Instruction Manual

Models : LVC-SX811HM

LVC-SX811HP

Before installing, operating or adjusting this

product, please read this instruction booklet

carefully and completely.

LVC-SX811HP_ENG_MFL-180 7/19/07 3:04 PM Page 1

This lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

dangerous voltage within the product’s enclo-

sure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and mainte-

nance (servicing) instructions in the litera-

ture accompanying the product.

FCC WARNING: This equipment may generate or use

radio frequency energy. Changes or modifications to

this equipment may cause harmful interference unless

the modifications are expressly approved in the

instruction manual. The user could lose the authority

to operate this equipment if an unauthorized change

or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful inter-

ference when the equipment is operated in a commer-

cial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accor-

dance with the instruction manual, may cause harmful

interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful

interference in which case the user will be required to

correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall

be provided in the cable entries of this product in the

end user.

• Caution: Danger of explosion if battery is incorrectly

replaced. Replaced only with the same or equivalent

type recommended by the manufacturer. Dispose of

used batteries according to the manufacturer’s

instructions.

• Holes in metal, through which insulated wires pass,

shall have smooth well rounded surfaces or shall be

provided with brushings.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

LVC-SX811HP_ENG_MFL-180 7/19/07 3:04 PM Page 2

Warning: Do not install this equipment in a confined

space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with

the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic envi-

ronment this product may cause radio interference in

which case the user may be required to take adequate

measures.

Warning: To reduce a risk of fire or electric shock, do

not expose this product to rain or moisture.

Caution: This installation should be made by a quali-

fied service person and should conform to all local

codes.

Caution: To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified personnel only.

Caution: The apparatus should not be exposed to

water (dripping or splashing) and no objects filled with

liquids, such as vases, should be placed on the appara-

tus.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is

attached to a product it means the product is

covered by the European Directive

2002/96/EC.

2. All electrical and electronic products should

be disposed of separately from the municipal

waste stream via designated collection facili-

ties appointed by the government or the local

authorities.

3. The correct disposal of your old appliance

will help prevent potential negative conse-

quences for the environment and human

health.

4. For more detailed information about disposal

of your old appliance, please contact your

city office, waste disposal service or the shop

where you purchased the product.

This product is manufactured to comply

with the EEC DIRECTIVE 89/336/EEC,

93/68/EEC and 2006/95/EC.

To disconnect power from the mains, pull out the

mains cord plug.

When install the product, ensure that the plug is easily

accessible.

LVC-SX811HP_ENG_MFL-180 7/19/07 3:04 PM Page 3

Important Safety Instructions

1. Read these instructions. - All these safety

and operating instructions should be read

before the product is operated.

2. Keep these instructions. - The safety, operat-

ing and use instructions should be retained for

future reference.

3. Heed all warnings. - All warnings on the prod-

uct and in the operating instructions should be

adhered to.

4. Follow all instructions. - All operating and

use instructions should be followed.

5. Do not use this apparatus near water. - For

example: near a bath tub, wash bowl, kitchen

sink, laundry tub, in a wet basement; near a

swimming pool; etc.

6. Clean only with dry cloth. - Unplug this prod-

uct from the wall outlet before cleaning. Do not

use liquid cleaners.

7. Do not block any ventilation openings.

Install in accordance with the manufactur-

er's instructions. - Slots and openings in the

cabinet are provided for ventilation, to ensure

reliable operation of the product, and to protect

it from over- heating. The openings should

never be blocked by placing the product on a

bed, sofa, rug or other similar surface. This

product should not be placed in a built-in instal-

lation such as a bookcase or rack unless prop-

er ventilation is provided and the manufactur-

er’s instructions have been adhered to.

8. Do not install near any heat sources such

as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that pro-

duce heat.

LVC-SX811HP_ENG_MFL-180 7/19/07 3:04 PM Page 4

Important Safety Instructions

9. Do not defeat the safety purpose of the

polarized or grounding-type plug. A polar-

ized plug has two blades with one wider than

the other. A grounding type plug has two

blades and a third grounding prong. The

wide blade or the third prong are provided

for your safety. If the provided plug does not

fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked

on or pinched particularly at plugs, conven-

ience receptacles, and the point where they

exit from the apparatus.

11. Only use attachments/accessories specified

by the manufacturer.

12. Use only with the cart, stand, tripod, brack-

et, or table specified by the manufacturer,

or sold with the apparatus. When a cart is

used, use caution when moving the

cart/apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning storms

or when unused for long periods of time.

14. Refer all servicing to qualified service per-

sonnel. Servicing is required when the appa-

ratus has been damaged in any way, such

as power-supply cord or plug is damaged,

liquid has been spilled or objects have fall-

en into the apparatus, the apparatus has

been exposed to rain or moisture, does not

operate normally, or has been dropped.

LVC-SX811HP_ENG_MFL-180 7/19/07 3:04 PM Page 5

Contents and Features

Contents

Part Names and Functions . . . . . . . . . . . . . . .7-9

Connections . . . . . . . . . . . . . . . . . . . . . . . .10

Mounting the Lens . . . . . . . . . . . . . . . . . .11-12

Concerning Auto-Iris Lenses . . . . . . . . . . .13-14

Function Switch Settings . . . . . . . . . . . . . . . .15

Day&Night Function Settings . . . . . . . . . . .16-17

Line Lock Phase Adjustment . . . . . . . . . . . . . .18

Flange-back Adjustment . . . . . . . . . . . . . . . .19

Installation of Camera . . . . . . . . . . . . . . . . .20

Specifications . . . . . . . . . . . . . . . . . . . . .21-22

Features

This color video camera is designed for use in mon-

itoring system.

• High resolution and high sensitivity with a 1/3

inch Super HAD CCD (Charge Coupled Device)

• CS Mount (Adapter Ring Mount for C Lens:

Optional)

• Line Lock when using AC24V power.

• Dual power : AC 24V or DC 12V

• Non-polarity DC12V

Maintenance of the unit

• Remove dust or dirt on the surface of the lens

with a blower.

• Use a dry soft cloth to clean the body. If it is

very dirty, use a cloth dampended with a small

quantity of neutral detergent and then wipe dry.

• Avoid the use of volatile solvents such as thin-

ners, alcohol, benzene, and insecticides. They

may damage the surface of the body.

LVC-SX811HP_ENG_MFL-180 7/19/07 3:04 PM Page 6

Part Names and Functions

1. Camera mounting bracket

The bracket can be fixed at the top or bottom

of the camera. (page 20)

2. Lens mount cap

The cap is installed to protect the lens mount

section. Remove the lens mount cap before

installing a lens.

3. Flange-back lock screw

4. Flange-back adjustment dial

LVC-SX811HP_ENG_MFL-180 7/19/07 3:04 PM Page 7

Part Names and Functions

5. Power indicator

Comes on when the power to the camera is on.

6. Power input terminal

AC 24V / DC 12 V input terminal.

This camera must always be operated a AC 24V

/ DC 12 V Certified/Listed, class 2 power sup-

ply only.

7. D&N connector for manual day setting

(See page 16)

8. D&N connector for manual night setting

(See page 16)

9. Lens iris output connector (LENS)

This 4- pin connector is used to send the Iris

control signal and power supply to an auto-iris

type lens.

LVC-SX811HP_ENG_MFL-180 7/19/07 3:04 PM Page 8

Part Names and Functions

10. Video output connector (BNC type)

Connect this connector to a device such as a

VCR or monitor with a VIDEO IN connector.

11. Function switches for manual setting

To set functions, use these dip switches.

12. ALC Lens Setting Switch

DC: When you attach an Auto Iris lens requir-

ing the DC control signal, please put this

switch in the DC position.

ELC: When you attach a manual or fixed lens,

please put this switch in the ELC position.

VIDEO: When you attach an Auto Iris lens

requiring the video control signal, please put

this switch in the VIDEO position.

13. Line lock phase adjustment volume

14. DC iris level adjustment volume

LVC-SX811HP_ENG_MFL-180 7/19/07 3:04 PM Page 9

Connections

Basic connection

The peripheral devices (VCR, monitor, lens, etc.),

AC adaptor and cables are not supplied.

1. Connecting the monitor

Make the video signal connection between the

camera and the monitor or time lapse VCR.

2. Use a commercially available

Certified/Listed, Class 2, AC 24V or DC 12V

adaptor.

Connect an AC 24V or DC 12V power source to

the POWER INPUT terminal on the back of the

camera.

3. Insert the plug of this power cord into a wall

outlet.

The POWER indicator will light.

To monitor’s Video

Input or Camera Input

LVC-SX811HP_ENG_MFL-180 7/19/07 3:04 PM Page 10

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Videocámara de otras marcas

Toshiba

Toshiba CAMILEO Z100 Manual de usuario

Panasonic

Panasonic NV-VS40B Manual de usuario

Canon

Canon RC 260 Manual de usuario

Sony

Sony Handycam DCR-DVD7E Manual de usuario

Brinno

Brinno TimeLapse TLC200 Manual de usuario

JVC

JVC GR-SXM68AC Guía de inicio rápido

Panasonic

Panasonic AG-HMC152EN Manual de usuario

Insignia

Insignia NS-DCC5HB09 - Camcorder - 720p Manual de usuario

MYDLINK

MYDLINK DCS-6100LH Manual de usuario

Sony

Sony video Hi8 Handycam CCD-TR555 Manual de usuario

SECURECOM

SECURECOM V-5014B Manual de usuario

Panasonic

Panasonic HDC-SD100 Manual de usuario

Sharper Image

Sharper Image U-VIDEO Manual de usuario

JVC

JVC AA-V15EG Manual de usuario

Canon

Canon LEGRIA HV40 Manual de usuario

Sony

Sony Handycam DCR-VX2000 Manual de usuario

RCA

RCA CC616 Manual de usuario

Panasonic

Panasonic NVM40 Manual de usuario