LevelOne FVT-0103TXFC Manual de usuario

10. FVT-0103TXFC Technical Specifications

•Standards : IEEE802.3u 10/100Base-TX, 100Base-FX

IEEE802.3af Power over Ethernet

•

UTP Cable : Cat. 5 cable and up to100m

Fiber Cable :

50/125, 62.5/125 or 100/140

m multi-mode

•PoE Power Reception Supports :

“Endpoint” via TP pin 1, 2, 3, 6

“ Midspan” via TP pin 4, 5, 7, 8

•LED Indicators :

POWER, PoE, TP LNK/ACT, 100, FX LNK/ACT,

FDX/COL

•Data Transfer Rate :

Speed Forwarding Rate

100Mbps 148,800 PPS

10Mbps 14,880 PPS

•Flow Control : IEEE802.3x compliant for full duplex

Backpressure flow control for half duplex

•Power Requirement :

60mA@-48VDC from IEEE802.3af PSE or PoE injector

•Ambient Temperature : 0°to 50°C

•Humidity : 5% to 90%

•Dimensions : 26.2(H) ×70.3(W) ×94(D) mm

•Complies with FCC Part 15 Class A and CE Mark

Note: For connecting this device to Router, Bridge or

Switch, please refer to the corresponding device's

Technical Manual.

S1-1 TP port mode : AUTO(default) or FORCE

S1-2 TP port speed : 100 or 10 when TP at Force

S1-3 TP port duplex : FDX or HDX when TP at Force

S1-4 LFP : LFP enabled(default) or disabled

S1-5 Fiber port duplex: 100FDX(default) or 100HDX

Note:

1. S1-2 and S1-3 will take effect only when S1-1 is set

at TP-FORCE.

2. S1-5 must be set to 100FDX for Single Fiber Model.

Warning:

⎯When TP NWay port is connected to TP 100FDX(force

mode) instead of NWay partner, it will result in 100HDX

mode with invalid collision signal

⎯Ensure that all network nodes are configured at an

identical operation mode. Improper operation and flow

control mode between TP and Fiber port connections will

render the LAN to work poorly

9. Cable Connection Parameter

100Base-X network allows 512-bit time delay between any

two node-stations in a collision domain. Switch-based Media

Converter breaks up TP and Fiber segments’ collision domain

to extend the cabling distance.

•TP Cable Limitations: Cat. 5 and up to 100m

•Converter Fiber Cable Limitations:

FVT-0103TXFC

Multi-mode Half-duplex 412m

Multi-mode Full-duplex 2Km

Fig. 11 S1—Bit 1, 2, 3, 4, 5 Configuration and Setting

LFP

TP-

UTO 100 FDX EN FDX-FX

TP-FORCE 10 HDX LFP HDX-FX

DIS

S1 1 2 3 4 5

8 1

6. LED Description

LED Color Function

FX LNK/ACT Green Lit when fiber connection is good

Blinks when fiber data is present

FDX/COL Amber Lit when full-duplex mode is active

Off when half-duplex is active

Blinks when collision is present

TP LNK/ACT Green Lit when TP connection is good

Blinks when TP data is present

TP 100 Green Lit when TP speed is 100Mbps

Off when TP speed is 10Mbps

PWR Green Lit when +5V power is coming up

PoE Green Lit when PoE power is coming up

7. DC Jack and AC-DC Power Adapter

The DC jack's central post is 2.5mm wide.

8. Connecting to TP, Fiber Device

Converter

TP Port

10/100TP

AUTO, FORCE selectable: Bit 1, 2, 3 of S1

a. AUTO: 10/100 NWay Auto-negotiation

b. FORCE: 100 or 10, FDX or HDX

Converter

Fiber Port

100FX

100Mbps duplex selectable: Bit 5 of S1

a. FDX for 100FDX fiber link partner, default

b. HDX for 100HDX fiber link partner

1. Overview

IEEE802.3u 100Mbps Fast Ethernet supports two types of

media, 10/100Base-TX and 100Base-FX, for network

connection. LFP (Link Fault Pass Through) feature enhances

the TP-Fiber Link integrity and conformity. Either one of TP

or Fiber port is in link-fail state, the LFP converter forces the

other port to be at link-disabled state. Comply with IEEE

802.3af, its advanced auto-sensing algorithm enables taking

power form IEEE 802.3af Power Source Equipment (PSE) or

Power over Ethernet (PoE) injector. It also supports high

safety with short circuit protection and power-in auto-

detection (power from AC/DC power adapter or PSE device).

The power adapter is optional, not included in the standard

package. Please contact your local dealer for purchasing.

2. Model Description

Model Power Description

FVT-0103TXFC 60mA@-48VDC over Cat.5

The 100Mbps Fiber Transceiver Wavelength

SC multi-mode 2Km 1310nm

DC Jack : 2.5mm

DC Input : +5V 2.5A

Fig. 10 DC+5V Input Jack and Dimension

2 7

3. Checklist

Before you start installing the FVT-0103TXFC Converter,

verify that the package contains the following:

⎯100TX to 100FX SC multi-mode POE Converter

⎯This User's Manual

Please notify your local dealer if any of the item is missing.

4. Installing the Converter

TP-Fiber Converter with Power Source Equipment

(PSE) ：

⇒Install the TP media cable to the IEEE 802.3af PSE

device or PoE injector (See Fig. 2)

⇒Install the media cable for network connection

Warning:

⎯Please make sure that the power of PSE device is turned

on, or else the converter will not work.

⎯In case that no 802.3af PSE is available or PSE with PoE

power fails, you may install an AC-DC adapter for a

backup solution. Do not connect PSE TP port and AC-DC

adapter at a time. The power adapter is optional, not

included in the standard package. Please contact your

local dealer for purchasing.

⇒Verify that the AC-DC adapter conforms to your

country AC power requirement and then insert the

power plug

⇒Install the media cable for network connection

Port

Default: AUTO

AUTO or FORCE setting, see Fig. 11 S1—Bit 1

Attach TP Cat. 5 cable to TP port, and the distance

can be up to 100m.

Use the straight-through cable to connect the switch

or workstation, the 10/100 TP port can support

AUTO MDI-X sensing.

Fiber

Port Default: 100FDX

"100FDX"/"100HDX" setting, see Fig. 11 S1—Bit 5

Note : ●indicates LNK/ACT LED Lit

○ indicates LNK/ACT LED Off

Warning:

The LFP ( Link Fault Pass Through) function works only

when both two converters own this capability in pairs.

Furthermore, both LFP converters should be supplied only

by the same manufacturer/vender. The connection coming

from LFP converters with odd models or non-LFP

converters will cease the LFP function.

● ○

○ ○

○ ○●

10/100

Switch 10/100

Switch

Fiber

Cable

TP TP

LFP LFP

Fiber

Cable

B A

○○ ○ ○●

○ ○

TP TP

10/100

Switch Remote

Station

10/100

Switch

LFPLFP

Fig. 7 Normal status via a pair of LFPs

10/100

Switch

LFP

●

LFP

10/100

Switch

●●

Fiber

Cable

● ●

Remote

Station

● ●

Fig. 8 The status as TP Cable A is broken

Remote

Station

Fig. 9 The status as Fiber Cable B or C is broken

6 3

5. Link Fault Pass Through

This PoE converter supports link fault pass through (LFP) in

TX/FX converter application. Link status on one port is

propagated to the other port to notice the remote nodes. If TP

port is unplugged, this converter stops transmission on fiber

port. This causes the remote fiber node link to fail. LED

shows the link failure on both TP and fiber ports. If fiber link

fails, this converter restarts auto-negotiation on TP port but

always stays in the link failure state. This causes the remote

TP node link to fail. LED also shows the link failure on both

TP and fiber ports. Refer to Fig. 7 shown below for the normal

status when the link succeeds. Also refer to Fig. 8 and Fig. 9

for the erroneous status when TP Cable A, Fiber Cable B or

Fiber Cable C fails to connect.

Note: Link fault pass through (LFP) function only takes effect

as S1-Bit4 (see Fig. 11) is enabled. Disabled S1-Bit4 will turn

this media converter into a general one.

100FX Fiber

Network

Fig. 1 The View of FVT-0103TXFC PoE Converter

RJ-45 Jack

Fig. 2 Connection among PSE Ethernet Switch, Fiber

and TP Cables

Cat. 5 Cable

Fiber Optic

PSE Ethernet

Switch(Refer to

Fig. 6)

Fig. 3 Power from PSE or PoE Injector

PoE PSE or

PoE Injecto

PoE TP-to-FX

Converter

100FX

Fiber

Network

4 5

TX RX FX TPLNK

/ACT

100

FDX

/COL

PWRPoE PD IN

10/100Base-TX to 100Base-FX

Bridge Media Converter

12 435

AUTO

100

LFP

FDX

LFP DIS

HDX

FORCE

HDX FX

5VDC

MADE IN TAIWAN

This device complies with

Part 15 of the FCC Rules

Note:

IEEE802.3af assigns pairs on the RJ-45 connector and Cat.5

cable, either Endpoint or Midspan.

Endpoint : -48V via TP pin 1,2,3,6

Midspan : -48V via TP pin 4,5,7,8

Fig. 4 FVT-0103TXFC PoE Converter Front Panel

Fig. 5 FVT-0103TXFC PoE Converter Rear Panel

Fig. 6 RJ-45 Male Connector

Tabla de contenidos

Otros manuales de Convertidor de medios de LevelOne

LevelOne

LevelOne Infinity IEC-2002 Manual de usuario

LevelOne

LevelOne VDS-1201 Manual de usuario

LevelOne

LevelOne Infinity IEC-1000 Manual de usuario

LevelOne

LevelOne VDS-0120 PSE Manual de usuario

LevelOne

LevelOne Infinity IEC-1400 Manual de usuario

LevelOne

LevelOne IEC-1300 Manual de usuario

LevelOne

LevelOne Infinity IEC-2001 Manual de usuario

LevelOne

LevelOne VDS-0130 PD Manual de usuario

LevelOne

LevelOne GVM-1101 Manual de usuario

LevelOne

LevelOne VDS-0110 Manual de usuario

LevelOne

LevelOne IEC-4000 Manual de usuario

LevelOne

LevelOne FVT-2001 Manual de usuario

LevelOne

LevelOne GVT-2010 Manual de usuario

LevelOne

LevelOne Infinity IEC-1200 Manual de usuario

LevelOne

LevelOne FVT-2002 Manual de usuario

LevelOne

LevelOne FVT-2202 Manual de usuario

LevelOne

LevelOne Infinity IEC-1040 Manual de usuario

LevelOne

LevelOne POS-4001 Manual de usuario

LevelOne

LevelOne FVT-6001 Manual de usuario

LevelOne

LevelOne FVM-1101 Manual de usuario

LevelOne

LevelOne GVT-2000 Manual de usuario

LevelOne

LevelOne DSS-1000 Manual de usuario

LevelOne

LevelOne Infinity IEC-1020 Manual de usuario

LevelOne

LevelOne GVT-2000 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario