Lenze C 750 Guía

Controller

c750

Commissioning | EN

Contents

1 About this document 7

1.1 Document descripon 7

1.2 Further documents 7

1.3 Notaons and convenons 8

2 Safety instrucons 9

2.1 Basic safety instrucons 9

2.2 Applicaon as directed 9

2.3 Handling 9

2.4 Residual hazards 10

3 Product informaon 12

3.1 Idencaon of the products 12

3.2 Features 12

3.3 SD card 13

3.4 CFast card 13

3.5 Backplane bus 14

3.6 Monitor, keyboard and mouse 14

3.7 Licence informaon 14

4 Mechanical installaon 15

4.1 Mounng the controller 15

5 Commissioning 16

5.1 Installaon of »PLC Designer« 16

5.2 Commissioning 16

5.3 Connect controller and Engineering PC 17

5.4 Set IP address on the PC 17

5.5 Start controller 18

5.6 Access to SD card 19

5.7 Create PLC program 20

5.8 Create task 21

5.9 Compile PLC program code 21

5.10 Establish connecon between controller and »PLC Designer« 21

5.11 Log in to the controller (load conguraon) 22

5.12 Parameterize controller 23

5.12.1 General informaon on parameter seng 23

5.12.1.1 Addressing of the parameters 23

5.12.1.2 Structure of the parameter descripons 23

5.12.2 Saving the parameter sengs 24

5.12.3 Reset parameters to default 24

5.13 Start PLC program 25

5.14 Generate boot applicaon 25

Contents

6 Device sengs 26

6.1 Device name 26

6.2 Host name 26

6.3 Engineering port 27

6.4 Name server addresses 27

6.5 Time 28

6.5.1 NTP server addresses 29

6.6 Device commands 30

6.6.1 Save parameter sengs 31

6.6.2 Reset parameters to default 31

6.6.3 Restart device 32

6.6.4 Start/stop applicaon 32

6.6.5 Load boot project 33

6.6.6 Delete logbook 33

6.6.7 Export logbook 33

6.6.8 Delete log les 34

7Congure engineering port 35

7.1 Conguraon via le 36

7.2 Automac conguraon via parameters 36

7.3 Manual conguraon via parameters 36

Contents

8Conguring the network 37

8.1 EtherCAT 38

8.1.1 EtherCAT state machine 39

8.1.2 Addressing of the slaves 41

8.1.3 Commissioning 42

8.1.4 Determine the physical EtherCAT conguraon (network scan) 43

8.1.5 Edit EtherCAT I/O mapping 46

8.1.5.1 Set PDO mapping 46

8.1.5.2 Acvate PDO mapping 46

8.1.6 Restart network 47

8.1.7 Parameter data transfer 47

8.1.8 Diagnoscs 48

8.1.8.1 EtherCAT master diagnoscs 48

8.1.9 Error scenarios 55

8.1.9.1 "Pre-Operaonal" EtherCAT state is not achieved 55

8.1.9.2 "Operaonal" EtherCAT state is not achieved 56

8.1.9.3 A slave does not accept a cyclic frame 56

8.1.9.4 The sync manager conguraon is invalid 56

8.1.9.5 The I/O conguraon is invalid 56

8.1.9.6 Error during process data transfer 56

8.1.9.7 The network cable is not connected. 57

8.1.9.8 A sent frame is not returned to the master 57

8.1.9.9 The output shas make a cracking sound 57

8.1.9.10 The drive shas do not rotate 58

8.1.10 Advanced conguraon 58

8.1.10.1 Device idencaon 58

8.1.10.2 Synchronisaon with "distributed clocks" (DC) 60

8.1.10.3 Set DC synchronizaon 62

8.1.11 Modular machine conguraon 65

8.1.11.1 Behavior of the EtherCAT master 65

8.1.11.2 Mandatory slaves/Oponal slaves 66

8.1.11.3 Conguraon les 67

8.1.11.4 Address assignment 68

8.1.11.5 Error messages 69

8.2 PROFINET 71

8.2.1 Commissioning 73

8.2.1.1 Restarng or stopping the communicaon 73

8.2.1.2 Sengs in the Siemens »TIA Portal« 74

8.2.1.3 Device descripon le 74

8.2.2 Basic seng and opons 75

8.2.2.1 Staon name and IP conguraon 75

8.2.2.2 Suppress diagnosc messages to the IO controller 76

8.2.3 Process data transfer 76

8.2.4 Parameter data transfer 77

8.2.5 Monitoring 78

8.2.6 Diagnoscs 79

8.2.6.1 LED status display 79

8.2.6.2 Informaon on the network 79

Contents

9 Device funcons 81

9.1 Device idencaon 81

9.2 Switch-o behavior 82

9.2.1 Retain variables and persistent variables 82

9.3 Reset controller 83

10 Open system funconality 84

10.1 Preinstalled Windows 10 IoT Enterprise 85

10.1.1 Back up and restore the Windows installaon image 86

10.1.2 Protect Windows from unwanted changes 87

10.1.3 Reset Windows to the conguraon state 87

10.1.4 Back up and restore the Windows system image 88

10.2 Set up remote desktop connecon to the open system 88

10.3 Install UPS driver 89

10.4 Set me and me zone 89

10.5 Virtual network interface 90

10.6 Device commands for operang system control 91

11 Replace controller 93

11.1 Dismount controller 93

11.2 Install new controller 94

11.3 Reuse retain data 94

12 Upgrade/downgrade of the controller 95

13 Diagnoscs and fault eliminaon 96

13.1 LED status display 96

13.2 Logbook 97

13.3 Diagnosc parameters 98

13.3.1 PLC diagnoscs 98

13.3.2 Network diagnoscs 99

13.3.3 Service life diagnoscs 100

13.4 Error handling 100

14 Appendix 101

14.1 Parameter aribute list 101

Contents

1 About this document

These instrucons apply to the c750 controller.

If you commission a controller together with other devices (e. g. I/O system, inverter, other

network components), please observe the documentaon for the other devices in the

automaon system as well.

WARNING!

Read this documentaon carefully before starng any work.

▶Please observe the safety instrucons!

1.1 Document descripon

This documentaon is valid up to rmware version:

Firmware version Soware data version Date

V_1_3_0 V_1_3_0_002 2019-09-28

1.2 Further documents

For certain tasks, informaon is available in addional documents.

Document Contents/topics

Conguraon document Basic informaon on conguring and ordering the product

"Funconal safety" conguraon document Basic informaon on conguring the "funconal safety" of the product

Mounng instrucons Basic informaon on installing the product

Commissioning document Basic informaon on commissioning the product

Lenze online help Basic and addional informaon on using Lenze Engineering tools to commission the product,

congure its network and diagnose it.

For certain tasks, informaon is available in other media.

Form Contents/topics

Engineering Tools For commissioning

AKB arcles Addional technical informaon for users in the Applicaon Knowledge Base

CAD data Download in dierent formats from the EASY Product Finder

EPLAN macros Project planning, documentaon and management of projects for EPLAN P8.

These media can be found here: Lenze.com

A detailed descripon of the EtherCAT modules can be found on the Internet:

www.Lenze.com à Downloads

Informaon and tools with regard to the Lenze products can be found on the

Internet: www.Lenze.com à Downloads

About this document

Document descripon

1.3 Notaons and convenons

This document uses the following convenons to disnguish dierent types of informaon:

Numeric notaon

Decimal separator Point The decimal point is always used.

Example: 1 234.56

Warning

UL warning UL Are used in English and French.

UR warning UR

Text

Engineering tools » « Soware

Example: »Engineer«, »EASY Starter«

Icons

Page reference ¶Reference to another page with addional informaon

Example: ¶ 16 = see page 16

Documentaon reference ,Reference to another documentaon with addional informaon

Example: , EDKxxx = see documentaon EDKxxx

Layout of the safety instrucons

DANGER!

Indicates an extremely hazardous situaon. Failure to comply with this instrucon will result

in severe irreparable injury and even death.

WARNING!

Indicates an extremely hazardous situaon. Failure to comply with this instrucon may result

in severe irreparable injury and even death.

CAUTION!

Indicates a hazardous situaon. Failure to comply with this instrucon may result in slight to

medium injury.

NOTICE

Indicates a material hazard. Failure to comply with this instrucon may result in material

damage.

About this document

Notaons and convenons

2 Safety instrucons

Disregarding the following basic safety measures and safety informaon may lead to severe

personal injury and damage to property!

Observe all specicaons of the corresponding documentaon supplied. This is the

precondion for safe and trouble-free operaon and for obtaining the product features

specied.

Please observe the specic safety informaon in the other secons!

2.1 Basic safety instrucons

Personnel

The product must only be used by qualied personnel. IEC 60364 or CENELEC HD 384 dene

the skills of these persons:

•They are familiar with installing, mounng, commissioning, and operang the product.

•They have the corresponding qualicaons for their work.

•They know and can apply all regulaons for the prevenon of accidents, direcves, and

laws applicable at the place of use.

Product

The product must never be technically modied!

If you carry out any technical modicaons or alteraons that are impermissible, all your

warranty claims will become void and the product liability will be excluded!

Device protecon

•The maximum test voltage for insulaon tests between a control potenal of 24 V and PE

must not exceed 110 V DC (EN 61800−5−1).

2.2 Applicaon as directed

The product is a piece of electrical equipment. The product is solely suited to be installed in

control cabinets or similar closed electrical operang areas, and to implement control

concepts, operaonal concepts, or to represent informaon in customary industrial and

commercial areas.

For the purpose of prevenng injury to persons and damage to material assets, higher-level

safety systems have to be used!

2.3 Handling

•Never commission the product in the event of visible damage.

•The product must never be technically modied.

•Never commission the product before assembly has been completed.

•The product must never be operated without required covers.

•Establish, separate and change all electrical connecons only in deenergised state!

Safety instrucons

Basic safety instrucons

2.4 Residual hazards

Product

Observe the warning labels on the product!

Electrostac sensive devices:

Before working on the product, the sta must ensure to be free of electrostac charge!

Dangerous electrical voltage:

Before working on the product, make sure there is no voltage applied to the power terminals!

Aer mains disconnecon, the power terminals will sll carry the hazardous electrical voltage for the me given next to the

symbol!

High leakage current:

Carry out xed installaon and PE connecon in compliance with:

EN 61800−5−1 / EN 60204−1

Hot surface:

Use personal protecve equipment or wait unl the device has cooled down!

WARNING!

Dangerous electrical voltage

Error on device leads to overvoltage in the system.

▶For a voltage supply with 24 V DC (± 25 %), use a safely separated power supply unit

according to the applicable SELV/PELV requirements.

▶All components connected to USB and RJ45 must be electrically isolated from the mains

according to class III.

NOTICE

Short circuit in the device due to a missing cover.

Destrucon of the device.

▶Close the modules with the contact cover.

NOTICE

Incorrect arrangement of the I/O modules.

Malfuncon of the device.

▶Arrange the modules from le to right on the device.

▶Start with a power supply module or an I/O bus coupler.

NOTICE

Unstable LAN connecon due to the use of incorrect cable types.

The LAN connecon may be interrupted.

▶Exclusively use cables of the CAT5-S/FTP type or beer.

▶The unit is to be connected only to internal Ethernet networks without exing a facility and

being subjected to TNVs.

Safety instrucons

Residual hazards

Otros manuales para C 750

Tabla de contenidos

Otros manuales de Controladores de Lenze

Lenze

Lenze C 750 Manual de usuario

Lenze

Lenze i550 Series Instrucciones de montaje

Lenze

Lenze 9350 Manual de usuario

Lenze

Lenze L-force HighLine C 8400 Series Manual de usuario

Lenze

Lenze c300 Series Manual de usuario

Lenze

Lenze EPM-S900 Manual de usuario

Lenze

Lenze EVS9321-Ex Manual de usuario

Lenze

Lenze ETCHC Series, ETCHM Series Manual de usuario

Lenze

Lenze c250-S Manual de usuario

Lenze

Lenze L-force 8400 Series Instrucciones de montaje

Lenze

Lenze 94/940 Manual de usuario

Lenze

Lenze c300 Series Manual de usuario

Lenze

Lenze AC Tech M3103S Manual de usuario

Lenze

Lenze 9200 Series Manual de usuario

Lenze

Lenze C520 Guía

Lenze

Lenze Starttec E71MM402 Manual de usuario

Lenze

Lenze 482 Manual de usuario

Lenze

Lenze M MA Series Manual de usuario

Lenze

Lenze 4800 Manual de usuario

Lenze

Lenze L-force CS Series Manual de usuario

Lenze

Lenze SCL series Manual de usuario

Lenze

Lenze 9300 Series Guía del usuario

Lenze

Lenze 3200 C Series Manual de usuario

Lenze

Lenze 712 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario