Lenze C520 Guía

Controller

c520

Commissioning | EN

Contents

1 About this document 7

1.1 Document descripon 7

1.2 Further documents 7

1.3 Notaons and convenons 8

2 Safety instrucons 9

2.1 Basic safety instrucons 9

2.2 Applicaon as directed 9

2.3 Residual hazards 10

3 Product informaon 12

3.1 Idencaon of the products 12

3.2 Features 12

3.3 SD card 12

3.4 Backplane bus 13

3.5 Licence informaon 13

4 Mechanical installaon 14

4.1 Mounng the controller 14

5 Commissioning 15

5.1 Installaon of »PLC Designer« 15

5.2 Commissioning 15

5.3 Connect controller and Engineering PC 16

5.4 Set IP address on the PC 16

5.5 Start controller 17

5.6 Access to SD card 18

5.7 Create PLC program 19

5.8 Create task 20

5.9 Compile PLC program code 20

5.10 Establish connecon between controller and »PLC Designer« 20

5.11 Log in to the controller (load conguraon) 21

5.12 Parameterize controller 22

5.12.1 General informaon on parameter seng 22

5.12.1.1 Addressing of the parameters 22

5.12.1.2 Structure of the parameter descripons 22

5.12.2 Saving the parameter sengs 23

5.12.3 Reset parameters to default 23

5.13 Start PLC program 24

5.14 Generate boot applicaon 24

Contents

6 Device sengs 25

6.1 Device name 25

6.2 Host name 25

6.3 Engineering port 26

6.4 Name server addresses 26

6.5 Time 27

6.5.1 NTP server addresses 28

6.6 Device commands 29

6.6.1 Save parameter sengs 30

6.6.2 Reset parameters to default 30

6.6.3 Restart device 31

6.6.4 Start/stop applicaon 31

6.6.5 Load boot project 32

6.6.6 Delete logbook 32

6.6.7 Export logbook 32

6.6.8 Delete log les 33

7Congure engineering port 34

7.1 Conguraon via le 35

7.2 Automac conguraon via parameters 35

7.3 Manual conguraon via parameters 35

Contents

8Conguring the network 36

8.1 EtherCAT 37

8.1.1 EtherCAT state machine 38

8.1.2 Addressing of the slaves 40

8.1.3 Commissioning 41

8.1.4 Determine the physical EtherCAT conguraon (network scan) 42

8.1.5 Edit EtherCAT I/O mapping 45

8.1.5.1 Set PDO mapping 45

8.1.5.2 Acvate PDO mapping 45

8.1.6 Restart network 46

8.1.7 Parameter data transfer 46

8.1.8 Diagnoscs 47

8.1.8.1 EtherCAT master diagnoscs 47

8.1.9 Error scenarios 54

8.1.9.1 "Pre-Operaonal" EtherCAT state is not achieved 54

8.1.9.2 "Operaonal" EtherCAT state is not achieved 55

8.1.9.3 A slave does not accept a cyclic frame 55

8.1.9.4 The sync manager conguraon is invalid 55

8.1.9.5 The I/O conguraon is invalid 55

8.1.9.6 Error during process data transfer 55

8.1.9.7 The network cable is not connected. 56

8.1.9.8 A sent frame is not returned to the master 56

8.1.9.9 The output shas make a cracking sound 56

8.1.9.10 The drive shas do not rotate 57

8.1.10 Advanced conguraon 57

8.1.10.1 Device idencaon 57

8.1.10.2 Synchronisaon with "distributed clocks" (DC) 59

8.1.10.3 Set DC synchronizaon 61

8.1.11 Modular machine conguraon 64

8.1.11.1 Behavior of the EtherCAT master 64

8.1.11.2 Mandatory slaves/Oponal slaves 65

8.1.11.3 Conguraon les 66

8.1.11.4 Address assignment 67

8.1.11.5 Error messages 68

8.2 PROFINET 70

8.2.1 Commissioning 72

8.2.1.1 Restarng or stopping the communicaon 72

8.2.1.2 Sengs in the Siemens »TIA Portal« 73

8.2.1.3 Device descripon le 73

8.2.2 Basic seng and opons 74

8.2.2.1 Staon name and IP conguraon 74

8.2.2.2 Suppress diagnosc messages to the IO controller 75

8.2.3 Process data transfer 75

8.2.4 Parameter data transfer 76

8.2.5 Monitoring 77

8.2.6 Diagnoscs 78

8.2.6.1 LED status display 78

8.2.6.2 Informaon on the network 78

Contents

9 Device funcons 80

9.1 Device idencaon 80

9.2 Opcal device idencaon 81

9.3 Switch-o behavior 82

9.3.1 Retain variables and persistent variables 82

9.4 Reset controller 83

9.5 Back up and restore data 84

9.5.1 Back up data 85

9.5.2 Restore data 86

9.6 Update rmware 88

10 Replace controller 90

10.1 Dismount controller 91

10.2 Install new controller 92

10.3 Reuse retain data 92

11 Diagnoscs and fault eliminaon 93

11.1 LED status display 93

11.2 Logbook 94

11.3 Diagnosc parameters 95

11.3.1 PLC diagnoscs 95

11.3.2 Network diagnoscs 96

11.3.3 Service life diagnoscs 97

11.4 Error handling 97

12 Appendix 98

12.1 Parameter aribute list 98

Contents

1 About this document

These Instrucons apply to the c520 controller.

If you commission a controller together with other devices (e. g. I/O system, inverter, other

network components), please observe the documentaon for the other devices in the

automaon system as well.

WARNING!

Read this documentaon carefully before starng any work.

▶Please observe the safety instrucons!

1.1 Document descripon

This documentaon is valid up to rmware version:

Firmware version Soware data version Date

V_1_4_0 V_1_4_0_001 2020-03-15

1.2 Further documents

For certain tasks, informaon is available in addional documents.

Document Contents/topics

Conguraon document Basic informaon on conguring and ordering the product

"Funconal safety" conguraon document Basic informaon on conguring the "funconal safety" of the product

Mounng instrucons Basic informaon on installing the product

Commissioning document Basic informaon on commissioning the product

Lenze online help Basic and addional informaon on using Lenze Engineering tools to commission the product,

congure its network and diagnose it.

For certain tasks, informaon is available in other media.

Form Contents/topics

Engineering Tools For commissioning

AKB arcles Addional technical informaon for users in the Applicaon Knowledge Base

CAD data Download in dierent formats from the EASY Product Finder

EPLAN macros Project planning, documentaon and management of projects for EPLAN P8.

These media can be found here: Lenze.com

A detailed descripon of the EtherCAT modules can be found on the Internet:

www.Lenze.com à Downloads

Informaon and tools with regard to the Lenze products can be found on the

Internet: www.Lenze.com à Downloads

About this document

Document descripon

1.3 Notaons and convenons

Convenons are used in this document to disnguish between dierent types of informaon.

Numeric notaon

Decimal separator Point Generally shown as a decimal point.

Example: 1 234.56

Warnings

UL Warnings UL Are used in English and French.

UR warnings UR

Text

Engineering Tools " " Soware

Example: "Engineer", "EASY Starter"

Icons

Page reference ¶Reference to another page with addional informaon.

Example: ¶ 16 = see page 16

Documentaon reference ,Reference to other documentaon with addional informaon.

Example: , EDKxxx = see documentaon EDKxxx

Layout of the safety instrucons

DANGER!

Indicates an extremely hazardous situaon. Failure to comply with this instrucon will result

in severe irreparable injury and even death.

WARNING!

Indicates an extremely hazardous situaon. Failure to comply with this instrucon may result

in severe irreparable injury and even death.

CAUTION!

Indicates a hazardous situaon. Failure to comply with this instrucon may result in slight to

medium injury.

NOTICE

Indicates a material hazard. Failure to comply with this instrucon may result in material

damage.

About this document

Notaons and convenons

2 Safety instrucons

Disregarding the following basic safety measures and safety informaon may lead to severe

personal injury and damage to property!

Observe all specicaons of the corresponding documentaon supplied. This is the

precondion for safe and trouble-free operaon and for obtaining the product features

specied.

Please observe the specic safety informaon in the other secons!

2.1 Basic safety instrucons

Product

•The product must only be used as directed.

•Never commission the product in the event of visible damage.

•The product must never be technically modied.

•Never commission the product before assembly has been completed.

•The product must never be operated without required covers.

•Connect/disconnect all pluggable terminals only in de-energized condion.

•Only remove the product from the installaon in the deenergized state.

Personnel

Only qualied and skilled personnel are allowed to work with the product. IEC 60364 and/or

CENELEC HD 384 dene the qualicaons of these persons as follows:

•They are familiar with the installaon, mounng, commissioning, and operaon of the

product.

•They possess the appropriate qualicaons for their tasks.

•They are familiar with all regulaons for the prevenon of accidents, direcves, and laws

applicable at the locaon and are able to apply them.

Product

The product must never be technically modied!

If you carry out any technical modicaons or alteraons that are impermissible, all your

warranty claims will become void and the product liability will be excluded!

Device protecon

•The maximum test voltage for insulaon tests between a control potenal of 24 V and PE

must not exceed 110 V DC (EN 61800−5−1).

2.2 Applicaon as directed

The product is a piece of electrical equipment. The product is solely suited to be installed in

control cabinets or similar closed electrical operang areas, and to implement control

concepts, operaonal concepts, or to represent informaon in customary industrial and

commercial areas.

For the purpose of prevenng injury to persons and damage to material assets, higher-level

safety systems have to be used!

Safety instrucons

Basic safety instrucons

2.3 Residual hazards

Even if notes given are taken into consideraon and protecve measures are implemented,

the occurrence of residual risks cannot be fully prevented.

The user must take the residual hazards menoned into consideraon in the risk assessment

for his/her machine/system.

If the above is disregarded, this can lead to severe injuries to persons and damage to

property!

Product

Observe the warning labels on the product!

Dangerous electrical voltage:

Before working on the product, make sure there is no voltage applied to the power terminals!

Aer mains disconnecon, the power terminals will sll carry the hazardous electrical voltage for the me given next to the

symbol!

Electrostac sensive devices:

Before working on the product, the sta must ensure to be free of electrostac charge!

High leakage current:

Carry out xed installaon and PE connecon in compliance with:

EN 61800−5−1 / EN 60204−1

Hot surface:

Use personal protecve equipment or wait unl the device has cooled down!

WARNING!

Dangerous electrical voltage

Error on device leads to overvoltage in the system.

▶For a voltage supply with 24 V DC (± 25 %), use a safely separated power supply unit

according to the applicable SELV/PELV requirements.

▶All components connected to USB and RJ45 must be electrically isolated from the mains

according to class III.

NOTICE

Short circuit in the device due to a missing cover.

Destrucon of the device.

▶Close the modules with the contact cover.

NOTICE

Incorrect arrangement of the I/O modules.

Malfuncon of the device.

▶Arrange the modules from le to right on the device.

▶Start with a power supply module or an I/O bus coupler.

Safety instrucons

Residual hazards

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Lenze

Lenze

Lenze SCL series Manual de usuario

Lenze

Lenze 9300 Series Guía del usuario

Lenze

Lenze EPM-S900 Manual de usuario

Lenze

Lenze AC Tech M3103S Manual de usuario

Lenze

Lenze Starttec E71MM402 Manual de usuario

Lenze

Lenze 9350 Manual de usuario

Lenze

Lenze EVS9321-Ex Manual de usuario

Lenze

Lenze c250-S Manual de usuario

Lenze

Lenze 530 series Manual de usuario

Lenze

Lenze 9300 Series Guía del usuario

Lenze

Lenze L-force CS Series Manual de usuario

Lenze

Lenze 9215 Manual de usuario

Lenze

Lenze 8400 StateLine C Manual de usuario

Lenze

Lenze ETCHC Series, ETCHM Series Manual de usuario

Lenze

Lenze 9300 Series Guía

Lenze

Lenze 3200 C Series Manual de usuario

Lenze

Lenze L-force EDK94AZHN26 Manual de usuario

Lenze

Lenze 94/940 Manual de usuario

Lenze

Lenze M MA Series Manual de usuario

Lenze

Lenze 4800 Manual de usuario

Lenze

Lenze c300 Series Manual de usuario

Lenze

Lenze i550 Series Instrucciones de montaje

Lenze

Lenze P30GAP Series Manual de usuario

Lenze

Lenze 490 Series Manual de lista de piezas

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario