Lenovo ThinkServer RD240 Manual de usuario
Rack installation instructions
Be sure to read and understand the documentation that comes with the rack cabinet for safety and
cabling information. Before you install the server in a rack cabinet, review the following guidelines:
vTwo or more people are required to install devices 2U or larger in a rack cabinet.
vMake sure that the room air temperature is below 35°C (95°F).
vDo not block any air vents; usually 15 cm (6 inches) of space provides proper airflow.
vDo not leave open spaces above or below an installed server in your rack cabinet. To help prevent
damage to server components, always install a blank filler panel to cover the open space and to help
ensure proper air circulation.
vInstall the server only in a rack cabinet with perforated doors.
vStart from the bottom of the rack cabinet for the device installation.
vInstall the heaviest device in the bottom of the rack cabinet.
vDo not extend more than one device out of the rack cabinet at the same time.
vRemove the rack doors and side panels to provide easier access during installation.
vConnect the server to a properly grounded outlet.
vDo not overload the electrical outlet when you install multiple devices in the rack cabinet.
vInstall the server in a rack that meets the following requirements:
– Minimum depth of 70 mm (2.76 inches) between the front mounting flange and inside of the front
door.
– Minimum depth of 157 mm (6.18 inches) between the rear mounting flange and inside of the rear
door.
– Minimum depth of 740 mm (29.13 inches) and maximum depth of 910 mm (35.83 inches) between
the front and rear mounting flanges to support the use of the cable-management arm.
Use safe practices when lifting.
≥18 kg (39.7 lb) ≥32 kg (70.5 lb) ≥55 kg (121.2 lb)
Do not place any object on top of
rack-mounted devices.
Remove the left and right guide rail components from the package. The illustration below shows the
components of the right guide rail. The components of the left guide rail are the same as those of the
right.
1 Retaining screw for the front bracket
2 Pin on the front bracket
3 Front bracket
4 Bearing bracket
5 Rear bracket
Remove the retaining screws on the front and rear
brackets.
2
According to the length between the front post and
the rear post of the rack, adjust the length of rail by
moving the rear bracket of the rail 1 until the
pins at the front and rear of the brackets click into
the holes in the rack posts. When the pins are in
place, install the retaining screws on the front and
rear of the bracket.
Notes:
1. The stretching range of the outer guide rail is
740 mm (29.13 inches) to 910 mm (35.83 inches).
Confirm the size of the rack before the
installation.
2. The left and the right outer guide rails should
be fixed to the left and the right posts of the
rack at the same level.
3. If the holes in the post are square holes, you can
operate according to the above methods.
4. If the holes in the post are round holes, remove
the retaining screws and pins on the front and
rear brackets and install the pins shipped with
guide rails. Then install the retaining screws
shipped with guide rails to secure the guide
rails onto rack.
Place the server on the bearing bracket and push it
inside. While pushing the server, you have to
support the bottom of the server with hands to
avoid the drop of the server.
When the server is in place, install the two retaining
screws on the left and right handles to secure the
server on the rack.
3
To remove the server from the rack, reverse these instructions. Store this information with your server
documentation for future use.
First Edition (April 2010)
Printed in USA
Lenovo and the Lenovo logo are trademarks of Lenovo in the United States, other countries, or both.
© Copyright Lenovo 2010.
LENOVO products, data, computer software, and services have been developed exclusively at private expense and
are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights
to use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered
pursuant a General Services Administration ″GSA″contract, use, reproduction, or disclosure is subject to restrictions
set forth in Contract No. GS-35F-05925.
(1P) P/N: 46U3543
Otros manuales para ThinkServer RD240
14
Tabla de contenidos
Otros manuales de Servidor de Lenovo
Lenovo
Lenovo ThinkServer TS200v Manual de lista de piezas
Lenovo
Lenovo ThinkServer RD330 Guía de inicio rápido
Lenovo
Lenovo System x3750 M4 Manual de usuario
Lenovo
Lenovo ThinkServer RD120 Type 6444 Manual de usuario
Lenovo
Lenovo ThinkServer RD530 Manual de lista de piezas
Lenovo
Lenovo ThinkServer TS200v Manual del propietario
Lenovo
Lenovo ThinkServer RD530 Manual
Lenovo
Lenovo ThinkSystem ST650 V2 Manual de servicio
Lenovo
Lenovo ThinkServer RD340 Instrucciones de funcionamiento
Lenovo
Lenovo ThinkServer TD200 Manual de usuario
Lenovo
Lenovo ThinkSystem SR590 Manual de usuario
Lenovo
Lenovo ThinkServer RD210 Manual de usuario
Lenovo
Lenovo ThinkServer TS100 Manual de usuario
Lenovo
Lenovo HR650X V2 Manual de usuario
Lenovo
Lenovo ThinkServer 1045 Manual de usuario
Lenovo
Lenovo ThinkServer RD330 Guía
Lenovo
Lenovo ThinkServer TD100 Manual de usuario
Lenovo
Lenovo ThinkServer RD120 Manual de usuario
Lenovo
Lenovo ThinkServer TD200x Manual de usuario
Lenovo
Lenovo THINKSERVER RS210 Guía
