Leister EXAMO 100 Manual de usuario

Leister Technologies AG

Galileo-Strasse 10

6056 Kaegiswil

Switzerland

+41 41 662 74 74

leister@leister.com

leister.com

EXAMO 100

English

1. Important Safety Instructions 3

2. Application 4

1.1 Intended use 4

1.2 Non-intended use 4

3. Technical Data 5

4. Your EXAMO100 Testing Device 6

4.1 Type plate and identication 6

4.2 Scope of delivery (standard equipment in the storage box) 6

4.3 Overview of device parts 7

5. Commissioning the EXAMO100 8

5.1 Work environment and safety 8

5.2 Preparation and operation 9

5.3 Testing with EXAMO100 9

6. Quick Guide EXAMO100 10

7. Frequently Asked Questions, Causes And Measures EXAMO100 11

8. Maintenance 11

9. Declaration of Conformity 12

Table of Contents

EXAMO 100

Testing Device

Congratulations on the purchase of your EXAMO100

You have chosen a rst-class tester.

It was developed and produced in accordance with the latest technology in the plastics-processing industry.

You can nd more information about the EXAMO 100 tester at leister.com

We recommend that you always keep the instruction manual with the device.

1. Important Safety Instructions

Warning

Keep handles and grip surfaces dry, clean and free from oil and grease. Slippery handles and grip

surfaces do not permit safe operation and control of the device in unforeseen situations.

The device should only be operated only by trained specialists or under their supervision.

Children are not permitted to operate the device.

You need a cordless drill to operate the EXAMO 100. Read the operating instructionsof the manufacturer

and observe its warning and safety instructions.

Operating Instructions(Translation of the Original User Manual)

The EXAMO 100 tensile tester is intended for professional use and is used for destructive testing of weld seam quality.

The EXAMO 100 tensile tester is to be used for testing plastic membranes made of PE-HD and PE-LD with a thickness

of 0.5–3.0 mm and a maximum width of 25 mm.

To use the EXAMO 100 testing device, a cordless drill with bit holder equipped with a gear selector switch for the slow

speed stage is required.

Any other use or any use beyond the type of use described is deemed non-intended use.

1.1 Intended use

1.2 Non-intended use

2. Application

Subject to change without prior notice.

3. Technical Data

EXAMO100

Distance mm 100

Spindle pitch mm/rotation 0.75

Weight kg

lbs

1.4

3.1

bDimensions

a) mm

inch

283

11.1

b) mm

inch

2.8

c) mm

inch

1.9

Example:

The type designation and the series identication are marked on the type plate (6) of the device as attached.

Please transfer this information to your instruction manual. In the event of any inquiries to our representatives or

authorized Leister Service Centers, please always refer to this information.

Model:

Serial no.:

• 1 × EXAMO100 device

• 1 × Bit holder

• 1 × Original Quick Guide

• 1 × Safety instructions

4. Your EXAMO100 Testing Device

4.1 Type plate and identication

4.2 Scope of delivery (standard equipment in the storage box)

1 2

6 5

1. Hexagonal adapter

(connection for cordless drill with bit holder)

2. Handle

3. Clamping jaws

4. Clamping lever

5. Clamping slide

6. Type plate

4.3 Overview of device parts

5. Commissioning the EXAMO100

Hold the testing device with one hand by the handle provided. Incorrect handling can lead to injuries.

The cordless drill may only be switched on when the testing device is being held by the handle.

Keep handles and grip surfaces dry, clean and free from oil and grease. Slippery handles and grip

surfaces do not permit safe operation and control of the device in unforeseen situations.

Start the testing process with a slow rotating movement. During a fast start-up, high action torque

can occur for a short time and lead to injuries. Use a cordless drill that can run at slow speeds.

Switch o the cordless drill immediately if the testing device jams. Be prepared for reaction torque

that cause a backlash. The testing device may jam if not used as intended.

Always use a bit holder for the connection between the cordless drill and the testing device.

A tight connection without a bit holder can lead to unexpected movements when operating the cordless

drill. The bit holder ensures easy and quick separation of the drive from the testing device.

Watch out for possible hazardsin the area such as e. g. risk of tripping, slipping, strong sunlight,

unattended devices, etc.

The device should only be operated only by trained specialists or under their supervision.

Children are not permitted to operate the device.

Read the operating instructionsof the cordless drill and screwdriver manufacturer and observe its

warning and safety instructions.

5.1 Work environment and safety

Warning

5.2 Preparation and operation

5.3 Testing with EXAMO100

• The cordless drill/driver must be equipped with a bit holder.

• Set the gear selector switch of the cordless drill to the slowest setting.

• The test piece (coupon) must be prepared so that it does not have any unclean cuts or damage. Ideally, the test

piece is punched with the COUPON CUTTER500 from Leister.

• Set distance between the clamping jaws (3) to approx. 15 mm. The distance can be adjusted by turning the

hexagonal adapter (1). When rotating clockwise, the clamping jaws (3) move apart. When rotating counter-

clockwise, the clamping jaws (3) move together.

• Open the clamping jaws (3) with aid of the clamping lever (4) and insert the test piece.

• Press the clamping jaws (3) with aid of the clamping lever (4) briey against the test piece.

• Hold the EXAMO100 with one hand on the handle (2) with a rm grip.

• Take a cordless drill equipped with a bit holder in your free hand and insert the hexagonal adapter (1) into the

bit holder.

• Set the direction of rotation of the cordless drill to clockwise.

• Press the on/off switch and pull the test coupon apart at a steady speed until it breaks. If the weld is correct,

the fracture point of the test coupon is outside the welding seams.

• After breaking the test coupon, adjust the direction of rotation of the cordless drill counterclockwise and move the

clamping slide (5) back to the starting position.

• Remove cordless drill with bit holder.

• Open the clamping jaws (3) with aid of the clamping lever (4) and remove the remains of the test coupon.

EXAMO 100

Quick Guide

QG EXAMO 100 / Art. 167.613 / 12.2022

Operating Instructions:

leister. link/qg-dlp-examo-100

6. Quick Guide EXAMO100

1. Set distance between the clamping jaws (3) (approx. 15 mm) and clamp test piece

2. Connect the cordless drill incl. bit holder to the EXAMO100 and pull out the test coupon

3. Retract the clamping slide (5) to original position and remove cordless drill incl. bit holder

4. Remove the remnants of the test coupon

The safety instructions in section 5 must be observed when using the device!

Tabla de contenidos

Otros manuales de Sistema de soldadura de Leister

Leister

Leister UNIPLAN 300 Manual de usuario

Leister

Leister Astro Manual de usuario

Leister

Leister UNIDRIVE 500 Manual de usuario

Leister

Leister Twinny T Manual de usuario

Leister

Leister TAPEMAT Manual de usuario

Leister

Leister TRIAC AT Manual de usuario

Leister

Leister SEAMTEK 2000 AT Manual de usuario

Leister

Leister WELDMAX Manual de usuario

Leister

Leister TWINMAT Manual de usuario

Leister

Leister Uniplan E Manual de usuario

Leister

Leister HEMTEK ST Manual de usuario

Leister

Leister Hot-Jet S Manual de usuario

Leister

Leister TRIAC ST Manual de usuario

Leister

Leister Uniplan Wedge Manual de usuario

Leister

Leister Uniroof E Manual de usuario

Leister

Leister Asto Manual de usuario

Leister

Leister VARIMAT V2 Manual de usuario

Leister

Leister VARIMAT S Manual de usuario

Leister

Leister FUSION 3C Manual de usuario

Leister

Leister VARIMAT V2 Series Manual de usuario

Leister

Leister TRIAC BT Manual de usuario

Leister

Leister VARIANT T1 Manual de usuario

Leister

Leister TRIAC BT Manual de usuario

Leister

Leister Twinny T Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario