Leica Stellaris 8 FALCON Guía de instalación

Leica Stellaris 8 FALCON quick manual

Version 1.0

Start-up

1. Check which stage adapter is in place. If you need to change the stage

adapter, do it before you start the microscope.

The adapter on the left is meant for 96/24 wellplates and 3D-printed

sample holders. The adapter on the right is meant for regular objective

glasses and 35 mm dishes. If you are working with incubation, remember

to pluck the holes on the adapter using spare objective glasses / dishes

found next to the microscope.

2. Turn on the microscope and the laser by

pressing the two buttons on the large black

box left of the microscope. Also turn on the

fluorescent lamp.

You cannot see the switches, but you can

feel the above the key. You do not need to

touch the key unless it is not in the position

shown here.

3. Start the computer and login with your

credentials

4. Start the Las X software.

5. Chose the appropriate configuration. For the time being this is ‘machine’.

6. Once the software had fully started, you can put

in your sample.

7. Got configuration (see below) and then chose

laser configuration (see right)

If you have DAPI / Hoechst in your sample, turn on the Diode 405 laser. Then

turn on the white light laser (WLL).

8. Now get back to the Acquisition side to set up the excitation / detection

paradigm.

If you have any saved settings, you can load them from the button (A).

If you need to make a new scheme you can add new sequences form the (F)

button. Then type the colour you have in your sample in the search window (B)

and use mouse cursor to drag the desired dye from the dye bar (C) to the

location of the desired detector (D) or (E). Adjust detection ranges if necessary.

Stellaris has two types of detectors, HyD S and HyD X.

HyD S Not quite as sensitive for FLIM or photon counting as HyD X, but tolerate

more light. Use these for bright channels and when making a coverslip

correction.

HyD X Use these detectors for dim channels / for photon counting applications /

when doing FLIM. NEVER USE HyD X FOR COVERSLIP CORRECTION.

You can use widget (G) to visualize the excitation / emission spectrum of your

chosen dyes to better design your excitation / detection paradigm.

Heating and CO2

The environmental controller is on the floatation table, next to the microscope. To turn on

the heating press the on/off button. Adjust the temperature to either 37 C (red) or 29C

(orange) depending on your needs or the colour of the next booking with 24 hours. Do not

turn on the CO2 unless you need it yourself. 5% CO2 should be sufficient for most samples.

To turn off the heating, press the off button down for about five seconds. To turn off the

heating, press the on/off button for about two seconds and then confirming the shutdown

from the screen.

Shutdown and preparing the microscope for the next

user

1. Save your data.

2. Check who is coming next to the microscope and what lasers they need

3. Check from IRIS if the next user is coming in two hours or less.

If the next user is coming in 2 hours or less, use protocol A, else use

protocol B

A. Turn off the 405 laser from the laser configuration menu if you used it and

the next user does not need it.

Shut down the software.

Remove your sample and clean the objectives.

Log off from the computer.

Check from IRIS if the next user within 24 hours needs the microscope

heated. If you used heating, leave the heating on, adjusting temperature if

needed. If you did not use heating, turn the heating on, adjusting

temperature if needed.

If you used CO2 turn it off.

disinfect all the surfaces you touched.

B. Turn off both the lasers from the laser configuration menu.

Shut down the software.

Remove your sample and clean the objectives.

Shut down the microscope.

Shut down the fluorescent lamp.

Check from IRIS if the next user needs the microscope heated. If you used

heating, leave the heating on, adjusting temperature if needed. If you did

not use heating, turn the heating on, adjusting temperature if needed.

Shut the computer down.

If you used CO2 turn it off.

Disinfect all the surfaces you touched

Tabla de contenidos

Otros manuales de Microscopio de Leica

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario

AO

AO Cycloptic Manual de usuario

Celestron

Celestron 44345 Manual de usuario