Leica Emspira 3 Manual de usuario

Emspira 3

User Manual

Emspira 3 User Manual 2

Contents

General Notes

General Notes 5

Important Safety Notes 6

Symbols Used 7

Safety Instructions 8

Introduction

Your Emspira 3 System 13

Optional Accessories 14

Emspira 3 Overview 15

System Overview 16

Assembly

Emspira 3 With Incident Light Base 18

Emspira 3 With Transmitted Light Base 20

Emspira 3 With Swing-arm Stand 22

Objective and Illumination

Installing Standard Planapochromatic Objective for Measurement

Tasks 26

Optional Achromatic Objective 27

Illumination: LED3000 RL 28

Illumination: LED3000 NVI 30

Illumination: LED5000SLI, LED3000SLI, LED3000 DI 31

Installation

Stand-Alone Mode: Cables and Terminals 34

Stand-Alone Mode: Installing Optional External Devices 35

PC Mode: Connecting a Computer, Installing Software 37

Network & WLAN Settings 38

Startup Procedure

LED Color & Blink Codes 40

Switching on Emspira 3 41

Switching on the Illumination 43

Focusing, Adjusting the Resistance of the Focus Drive 44

Changing Magniﬁcation, Click-stop Feature 45

Operation (Stand-Alone Mode)

Operation in Stand-Alone Mode 47

Operation (PC Mode)

Operation in PC Mode 49

Troubleshooting

Care and Maintenance

Care, Maintenance, Contact Persons 53

Spare Parts 55

Emspira 3 User Manual 3

Contents (Continued)

Disposal

Disposal 57

Speciﬁcations

Technical Data 59

Optical Data – Field of View 64

Optical Data – Magniﬁcation and Depth of Field* 66

Dimensional Drawings 68

Emspira 3 68

Emspira 3 With Incident Light Base 69

Emspira 3 With Incident Light Base 70

Emspira 3 With Transmitted Light Base 71

Emspira 3 With Swing-Arm Stand 72

Emspira 3 User Manual General Notes 4

General Notes

Emspira 3 User Manual General Notes 5

General Notes

Safety concept

Before using your Emspira 3 for the ﬁrst time,

please read the "Safety Concept" booklet inclu-

ded with Emspira 3. It contains additional infor-

mation on handling and care.

Cleaning

ODo not use any unsuitable cleaning agents,

chemicals or techniques for cleaning.

ONever use chemicals to clean colored

surfaces or accessories with rubberized

parts. This could damage the surfaces, and

specimens could be contaminated by abra-

ded particles.

Servicing

ORepairs may only be carried out by Leica

Microsystems-trained service technicians.

Only original Leica Microsystems spare

parts may be used.

Responsibilities of person in charge of

Emspira 3

OEnsure that the Emspira 3 is operated,

maintained and repaired by authorized and

trained personnel only.

Emspira 3 User Manual General Notes 6

Important Safety Notes

Applicable User Manuals

User manuals and updates are also available for

you to download and print from our website

www.leica-microsystems.com.

This user manual describes the special functions

of the Emspira 3 system and contains important

instructions for its operational safety, mainte-

nance, and accessories.

For information on the On-Screen Display (OSD)

in stand-alone mode, refer to the On-Screen-

Display User Manual.

The "Safety Concept" booklet contains additi-

onal safety information regarding the service

work, requirements and the handling of

Emspira 3, accessories and electrical accesso-

ries as well as general safety instructions.

You can combine individual system articles

with articles from external suppliers (e.g. cold

light sources, etc.). Please read the user manual

and the safety instructions from the supplier.

Before installing, operating or using Emspira 3

and the accessories, read the user manuals

listed above. In particular, please follow all

safety instructions.

To maintain Emspira 3 in its original condition

and to ensure safe operation, the user must

follow the instructions and warnings contained

in these user manuals.

Emspira 3 User Manual General Notes 7

Symbols Used

Warning! Safety hazard!

This symbol indicates especially

important information that is

mandatory to read and observe.

Failure to comply can cause the

following:

OPersonal injury!

OEmspira 3 malfunctions and damage.

Warning of hazardous electrical voltage

This symbol indicates especially

important information. Failure to

comply can cause the following:

OPersonal injury!

OEmspira 3 malfunctions and damage.

Microscope malfunctions and damage

This symbol warns against touching

hot surfaces, such as light bulbs.

Important information

This symbol indicates additional

information or explanations that are

intended to provide clarity.

Read and understand this user

manual before using this device.

Emspira 3 User Manual General Notes 8

Safety Instructions

Description

OThe individual modules fulﬁll the highest

requirements for observation and docu-

mentation with the Emspira 3 system.

Intended Use

ORefer to "Safety Concept" booklet

Non-intended use

ORefer to "Safety Concept" booklet

Never use Emspira 3 or its components for

surgical procedures (such as eye surgery) since

it is not intended for such use.

The digital microscope and accessories descri-

bed in this user manual have been tested for

safety and potential hazards. The responsible

Leica aﬃliate must be consulted whene-

ver Emspira 3 is altered, modiﬁed or used in

conjunction with non-Leica components that

are outside of the scope of this user manual!

Unauthorized alterations to Emspira 3 or

noncompliant use shall void all rights to any

warranty claims.

Place of use

ORefer to "Safety Concept" booklet

OElectrical components must be placed at

least 10 cm away from the wall and from

ﬂammable substances.

OAvoid large temperature ﬂuctuations, direct

sunlight and vibrations. These conditions

can distort measurements * and microgra-

phic images.

OIn warm and warm-damp climatic zones,

the individual components require special

care in order to prevent the build-up of

fungus.

* Measurement results and accuracy depend

on used objective, zoom and microscope

settings.

Responsibilities of person in charge of

Emspira 3

ORefer to "Safety Concept" booklet

Ensure that:

OThe Emspira 3 system and accessories are

operated, maintained and repaired by

authorized and trained personnel only.

OAll operators have read, understood and

observe this user manual, and particularly

the safety regulations.

Emspira 3 User Manual General Notes 9

Safety Instructions (Continued)

Repairs, service work

ORefer to "Safety Concept" booklet

OOnly original Leica Microsystems spare

parts may be used.

OBefore opening Emspira 3, switch oﬀ the

power and unplug the power cable.

OAvoid contact with powered electrical

circuits, which can lead to injury.

Transport

OUse the original packaging for shipping

or transporting the individual modules of

the Emspira 3 system and the accessory

components.

OIn order to prevent damage from vibrations,

disassemble all moving parts that (accor-

ding to the user manual) can be assembled

and disassembled by the customer and

pack them separately.

Integration in third-party products

ORefer to "Safety Concept" booklet

Disposal

ORefer to "Safety Concept" booklet

Legal regulations

ORefer to "Safety Concept" booklet

EC Declaration of Conformity

ORefer to "Safety Concept" booklet

EMC precautions

Prior to the installation of Emspira 3, the elec-

tromagnetic environment needs to be evalu-

ated. It is the responsibility of the operator to

ensure compliance with the environment.

If the instrument is being installed in any other

environment than an INDUSTRIAL, it cannot be

guaranteed that the equipment does not inter-

fere with other electronic devices.

INDUSTRIAL environments are part of a sepa-

rate power network, in most cases supplied by

a high- or medium-voltage transformer, dedi-

cated for the supply of installations feeding

manufacturing or similar plants.

Warning!

If Emspira 3 is being installed in any

other environment than an INDUS-

TRIAL, it cannot be guaranteed

that the radiated electromagnetic

emissions are not interfering with

other electronic devices.

Emspira 3 User Manual General Notes 10

Safety Instructions (Continued)

Health risks

Workplaces with digital microscopes and came-

ras facilitate and improve the viewing task, but

they also impose high demands on the eyes

and holding muscles of the user. Depending on

the duration of uninterrupted work, asthenopia

and musculoskeletal problems may occur.

For this reason, appropriate measures for reduc-

tion of the workload must be taken:

OOptimal arrangement of workplace, work

assignments and work ﬂow (changing tasks

frequently).

OThorough training of the personnel, giving

consideration to ergonomic and organizati-

onal aspects.

The ergonomic optics concept and the design

of Emspira 3 aim to limit the strain on the user

to the lowest possible level.

Microscope safety and EMC

Our microscope has been designed, produced

and tested in compliance with

OEN 61010-1: Safety requirements for elec-

trical equipment for measurement, control,

and laboratory use - Part 1: General require-

ments (for microscope)

OEN 62368-1: Audio/video, information and

communication technology equipment -

Part 1: Safety requirements (for optional

external power supply only)

ORadio interference suppression in compli-

ance with EN 55011 Class A

OEN 61326-1, Electrical equipment for

measurement, control and laboratory use –

EMC requirements

The microscope meets the requirements of EU

directives

O2014/35/EU Low voltage directive

O2014/30/EU EMC directive

O2011/65/EU RoHS directive

O2009/125/EC + VO EU 2019/1782

Ecodesign requirements for energy-related

products

and carries the CE mark.

The microscope must be disposed of

in accordance with 2012/19/EU WEEE

directive.

Intended for indoor use only in all EU member

states, EFTA states and Switzerland.

Tabla de contenidos

Otros manuales de Microscopio de Leica

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario

AO Cycloptic Manual de usuario

Celestron

Celestron 44345 Manual de usuario