Leica SP8-X Manual de usuario

Page | 1

Wellcome Trust Centre for Human Genetics

Cellular-Imaging Microscopy Core

The Leica SP8-X

SMD Confocal

Abridged INSTRUCTIONS

Page | 2

Introduction

The Leica SP8-X SMD confocal microscope is located in room 00/075, Lab 1. The

microscope is suitable for both live cell and fixed specimens on slides, and it will

run alongside the old Zeiss LMS 510 MetaHead confocal.

The new Leica SP8 has:

•An inverted DMI 6000 AFC microscope for live cell viewing

•Full live cell chamber with temperature, CO2 and humidity control

•SuperZ Galvo Stage and hardware Auto-Focus

•10x & 20x HC PL Fluotar air objectives, and 40x & 63x HC PL Apo oil CS2

objectives

•HC PL Apo x63 Mott Corr Water CS2 Objective with software control of the

correction collar

•Transmitted Light Brightfield Detector

•Inverted motorised scanning XY Stage including Mark & Find and

Autostitching/Mosaic Modules

•Passive anti-vibration microscope air-table

•AOBS filter free scanhead

•WLL2 tuneable pulsed single diode laser with 200 lines from 470 to 670nm,

including Pulse Picker for FLIM (80, 40, 20 10 MHz rep. rate)

•405nm Diode Laser for DAPI

•Two Internal Spectral Detector Channels (PMT)

•Two Internal Spectral Detector Channels (HyD) GaAsP

•SMD Excitation: 440nm laser pulsed for FLIM

•SMD Emission FLIM+FCS 2Ch HyD Fibre coupled X1 port

•SMD Filter Cubes Alexa488/Alexa633 and CFP/YFP, others available

•Twin premium Workstations and 30 inch Monitors

•Software Modules for all Acquisition modes, 3D, FRAP/FRET/FLIP, Spectral

Dye Separation, Online Dye Separation, Live Data Mode advanced live cell

imaging module, Image Processing, Measurement & Reporting

•Extra licence for PQ ST Offline Software FCS_FLIM

Page | 3

General information

The temp files during scanning are stored in C:\Temp\ which is generally fastest

on the C: drive. If the system crashes you may be able to recover images from

there.

On the Belkin USB monitor selection box under the monitors, the LED shows

yellow when the Leica SP8 Master PC monitor is active and green when the

PicaQuant Slave PC monitor is active. There’s a small button on the front left of

the USB box to switch between PC monitors, but this shouldn’t be necessary as

the mouse curser can move across both PC desktops to select that PC for

keyboard input and mouse control

Shut down the PicaTech Slave PC last first and switch on the Slave PC last (the

Leica SP8 Master PC goes on first). Log in with the same WTCHG account on both

PCs.

In the Leica LSM software, if you set the WWL to Constant Percent, at say 10%

the actual laser power will vary depending on the laser-line selected. If you set

the WWL to Constant Power, the power output of the WWL will be adjusted

automatically to give the same power level at every wavelength, so say 10% will

be approximately the same laser power at every laser line.

Pulse Picker gives the best image quality at the highest repetition rate.

Make sure the XC-Port is in ‘mirror’ position to block off any of the SMD

detectors.

When setting up a Tile Scan with the motorised stage, be careful not to accidently

click on the XY stage grid pad as the stage will move rapidly to that XY position.

There are hardbound manuals for the DMI6000 microscope and the Leica SP8

software/hardware. These are also available as pdf files in the both Master and

Slave PC hard drives.

Page | 4

The Leica DMI 6000 Microscope

Turning the right hand microscope focus control clockwise (away from you) raises

the objective (up). Turning the focus control anti-clockwise (towards you) lowers

the objective downwards (down).

The SmartMove remote control module on the desktop controls the motorised XY

stage and the motorised z focus. The top rotary knob controls stage travel in X

(across) and the bottom rotary knob controls stage travel in Y (up/down). The

rear rotary knob is the z focus.

Change objectives using the LAS AF software as you can directly select the

objective you want and it will allow you to go from air to oil objectives via a

software ‘yes/no’ prompt.

The microscope uses standard Zeiss 518F immersion oil. If oil drips off the bottle

applicator in use, you have too much oil on it. To avoid oil contamination of air

objectives, never change from an oil to an air objective when focussed on the

specimen under oil (you can start with the low power air objective and then move

up to the hi-power oil objective).

The large HC PL Apo x63 Mott Corr Water CS2 Objective with cable control of the

correction collar is for use with water immersion only – not 518F immersion oil.

Make sure you don’t select it in error when using the 63x oil objective. The water

immersion objective is easy to spot as the large correction collar motor sticks out

of the side of the objective.

For live cell work switch on the 37oC stage incubator at least 2 hours before use,

or ideally the night before. Type the words ‘Live Cell’ in your booking to tell other

prior SP8 users that the 37oC incubator heater is being left on for your later live

cell imaging slot.

We have a small 5% CO2 in air gas cylinder that can be used with the SP8 live cell

incubator. CO2 can be used with 2.5cm Mattek petri dishes, Labtek 3x1” glass

slides and multiwall plates using the appropriate stage insert.

Page | 5

Page | 6

To transfer user hardware control to the Leica DMI 6000 microscope from the LAS

software when looking down the microscope, press the diochroic filter selection

button (e.g. DAPI) and then ‘shutter’. Also use the fluorescence/transmitted light

toggle button on the bottom left side of the microscope.

The LCD screen on the microscope is simply a display screen (it does not have a

touchscreen).

Page | 7

Page | 8

SmartMove XYZ Stage Controller

Page | 9

Page | 10

Switch on Procedure

1) Switch the epi-fluorescence Xe mercury lamp power box on

2) Push the DMI6000 microscope top stand/condenser backwards

The motorised stage undergoes a fast initialisation sequence that moves the stage

rapidly to its end limits

3) Switch the PC Microscope rocker switch on (triple Green LED switches on

the right of the desk)

4) Switch the Scanner Power rocker switch on

Note that the Scanner Power must be on at least 30 seconds before you start the Leica

SP8 confocal software

5) Switch the Laser Power rocker switch on

6) Turn the Laser Emission key on

The White Light Laser (WLL) box will read 70% power by default. The WLL goes to

standby automatically if not used for a minute or so, but flicks back to full power when

scanning

7) Switch on the black mains distribution block on the rack on the far right

(Red LED rocker switch)

Note: this controls power to the PicaQuant PC and both PC monitors

8) The Leica SP8 Master PC monitor will switch on and this will start up the

PicaQuant Slave PC automatically

9) Press CNTRL-ALT-DEL to activate the login popup on the Leica SP8 Master

PC. Log in either with your Wellcome Trust Login account (WTCHG

network/internet access) or as Administrator (PC only no

network/internet)

10) Move the mouse curser to the PicaQuant Slave PC and click on the screen.

Press CNTRL-ALT-END to activate the login popup on the PicaQuant Slave

PC. Log in with either your Wellcome Trust Login account (WTCHG

network/internet access) or as Administrator (PC only no

network/internet)

11) Start up the Leica ‘LAS AF’ laser scanning software and select the

machine.xlhw and DMI6000 options

12) Select the objective required using the LAS AF software

Ensure that the 40x and 63x oil objectives are not the ‘travel’ lock down position: turn

anti-clockwise to release the objective top (ask if you need more information on this)

Tabla de contenidos

Otros manuales de Microscopio de Leica

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario

AO Cycloptic Manual de usuario

Celestron

Celestron 44345 Manual de usuario