Leica Digilux 2 Manual de usuario

Version 2.0

English

403020

GPS Equipment User Manual

GPS System 500

2GPS Equipment User Manual -2.0.0en

The instrument model and the serial number of your

product are indicated on the typeplate.

Enter the model and serial number in your manual and

always refer to this information when you need to contact

your agency or authorized service workshop.

GPS Receiver (SR) Type: Serial No.:

Terminal (TR) Type: Serial No.:

External Antenna (AT) Type: Serial No.:

The symbols used in this user manual have the following

meanings:

DANGER:

Indicates an imminently hazardous situation

which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a potentially hazardous situation or an

unintended use which, if not avoided, could

result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation or an

unintended use which, if not avoided, may result

in minor or moderate injury and/or appreciable

material, financial and environmental damage.

Important paragraphs which must be adhered to

in practice as they enable the product to be used

in a technically correct and efficient manner.

Meanings of symbols

Congratulations on your purchase of a new System

GPS500 from Leica Geosystems.

This manual contains important safety

directions

(refer to section "Safety

Instructions")

as well as instructions for

setting up the product and operating it.

Read carefully through the User Manual before you

switch on the instrument.

System GPS500

Product identification

GPS Equipment User Manual -2.0.0en

Introduction

System description

Getting started with new equipment

Care and Transport

Safety Instructions

Technical Specifications

View of chapters

4GPS Equipment User Manual -2.0.0en

Contents

Introduction ................................................... 5

System description ....................................... 6

GPS Receiver ............................................................. 6

Post-processing software ............................................ 6

Getting started with new equipment ........... 7

SKI-Pro (SKI-Pro-L1) post-processing software............ 7

ReceiverHardware...................................................... 7

Charge the batteries ......................................................... 8

Set Up the Equipment ...................................................... 9

Measuring with the default configuration parameters ...... 10

Processing the data in the SKI-Pro software............... 21

Care and Transport ..................................... 23

Transport .................................................................. 23

Storage ..................................................................... 23

Cleaninganddrying................................................... 23

Safety Instructions ...................................... 24

Intended use of equipment ........................................ 24

Permitted uses ............................................................... 24

Prohibited uses............................................................... 24

Limits to use.............................................................. 25

Responsibilities ......................................................... 25

Hazards in use .......................................................... 26

Main hazards in use ....................................................... 26

Electromagnetic acceptability ......................................... 31

FCC statement (applicable in U.S.)................................. 34

Technical Specifications............................. 35

SR520, SR530 Tracking Characteristics .................... 35

SR510 Tracking Characteristics................................. 36

GPS Antennas .......................................................... 36

Equipmentweights .................................................... 37

Power ....................................................................... 37

EnvironmentalSpecifications ..................................... 37

Separationdistances ................................................. 38

Baselineprecision ..................................................... 38

GPS Equipment User Manual -2.0.0en

Introduction

Leica Geosystems GPS System 500

comprises of GPS receiver hardware

and PC based software for GPS

Surveying and related applications.

The Main components are:

• GPS Receiver: Receive the

satellite signals.

• GPS Terminal: Keyboard and

Display device to steer the Receiver

• Post-processing software: Used

to process GPS data.

All of the instructions you

need in order to operate your

GPS system to a basic level

are contained in this user

manual.

In the "Technical Reference Manual"

and SKI-Pro Online Help (available in

English, French and other selected

languages only), there are more

detailed descriptions of special

software/hardware settings and

software/hardware functions. These

are intended for technical specialists.

The Technical Reference Manual is

available as an electronic PDF

document only. This document can

be found on the SKI-Pro installation

CD. For more information refer to the

file \MANUALS\README.TXT on the

SKI-Pro installation CD.

Introduction

6GPS Equipment User Manual -2.0.0en

System description

GPS Receiver

The GPS Receiver receives the GPS

signal from the NAVSTAR satellites

and calculates a range to all visible

satellites.

There are various types of Receivers

available:

SR510 - 12 L1 channels,

code and phase

SR520 - 12 L1, 12 L2 channels,

code and phase

SR530 - 12 L1, 12 L2 channels,

code and phase, RTK capable.

System description

The AT502 Antennas are intended for

use with the SR520 and SR530

Receivers. The AT501 Antenna is

intended for use with the SR510

Receiver.

See section 8 for technical

specifications.

The SR520 and SR530

Receivers use the GPS P

code signal, which by U.S.

policy is liable to be switched off

without notice. Phase measurements

on L2 are ensured however as these

Receivers automatically switch to

patented tracking techniques

Post-processing software

The Post-processing software is

used to process the observations

taken by the Receiver in order to

compute baselines and coordinates.

SKI-Pro Static Kinematic software is

the standard post-processing

software for dual-frequency

receivers. SKI-Pro-L1 is for single

frequency receivers. The user

interface for SKI-Pro and SKI-Pro -

L1 software packages are identical.

7Getting started with new equipment

GPS Equipment User Manual -2.0.0en

Getting started with new equipment

Receiver Hardware

The software contains a comprehen-

sive Online Help System. This Help

System is intended to replace the

function of a printed manual. If

required you may print out the entire

help for use as a hard copy reference

manual.

As a first step in getting familiar with

the software read the booklet

Getting

Started with SKI-Pro

delivered with

the SKI-Pro software package.

SKI-Pro (SKI-Pro-L1) post-processing software

In most cases, the software will be

installed by the local Leica

Geosystems representative and a

short introductory course will be

given.

Should this not be the case, install

the software as follows:

1. Insert the CD-ROM into the CD

drive of your PC.

2. Select Install SKI-Pro from the

menu.

3. Follow the instructions given by the

installation shield.

In most cases, a short introduction in

the use of the Receiverand Terminal

will be provided by the local Leica

Geosystems representative. If this is

not the case proceed as outlined in

the following sections.

Alternatively refer to the

Technical

Reference

PDF-manual available on

the SKI-Pro Installation CD.

Getting started with new equipment GPS Equipment User Manual -2.0.0en

Charge the batteries

Charge the batteries with the Leica

Geosystems battery charger pro-

vided. GEB121, GEB70 or GEB71

batteries may be used to power the

GPS equipment.

The GEB121 batteries may be

charged using GKL111 or GKL122

chargers.

The battery chargers are

intended for indoor use only.

Use a battery charger in a dry room

only, never outdoors. Charge batter-

ies only at an ambient temperature

between 10°C and 30°C ( 50°F to

86°F ). We recommend a tempera-

ture of 0°C to +20°C (32°F to 68°F)

for storing the batteries.

Use one Leica Geosystems

batteries, chargers and

accessories, or accessories recom-

mended by Leica Geosystems.

The GEB70 and GEB71 batteries

may be charged using GKL122 (with

charging cables), GKL23 or GKL22

chargers.

Refer to the appropriate manual

when using the chargers.

To attain full battery capacity

for new GEB121 batteries, it

is essential to repeate between three

and five complete charge/discharge

cycles.

1100Z07new

Charger

GKL122

GEB70 or

GEB71

Adapter plate

GDI121

9Getting started with new equipment

GPS Equipment User Manual -2.0.0en

Set Up the Equipment

Successful GPS surveys require

undisturbed satellite signal reception.

This means that GPS Receivers

should be set up in locations which are

free of obstructions. No obstacles like

trees, buildings, mountains, etc. should

block the line between the GPS

antenna and GPS satellites. This holds

true in particular for the Receiver which

serves as the reference.

For static and rapid static surveys,

the antenna must be kept perfectly

steady throughout the whole occupa-

tion of a point. This means that the

AT501 or AT502 antenna will usually

be put on a tripod.

Center and level the tripod precisely

above the survey marker. Place and

lock the carrier in the tribrach. Mount

the antenna onto the carrier.

Connect the antenna to the sensor

using the antenna cable.

Plug two camcorder batteries into the

backside of the sensor. Alternatively

or in addition you might want to

power the sensor externaly. In this

case connect a GEB71 battery to the

PWR- port of the sensor.

Attach the TR500 terminal to the

sensor, either directly or via a con-

nection cable by plugging it into the

TERMINAL-port on the sensor.

Insert a PC-card into the sensor.

Lock the lid carefully after

insertion of the card in order

to prevent water and dust from

getting inside the sensor.

Use the hook on the backside of the

sensor to hang it on one of the tripod

legs. Alternatively you may want to

leave the sensor inside the shipping

case.

Your System 500 sensor is now fully

ready for operation.

Getting started with new equipment GPS Equipment User Manual -2.0.0en

Measuring with the default configuration parameters

Step 2: Study the Icons

Most important at this stage is the top

part of the screen which contains

several symbols (icons) which

indicate the current system status.

Step 1: Power on

Turn on the sensor by pressing the ON-button on the terminal. One of the

following two screens will appear on the display:

Otros manuales para Digilux 2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de GPS de Leica

Leica

Leica mojo3D Manual de usuario

Leica

Leica RX1250 SmartRover Manual de usuario

Leica

Leica INEX 1-1296 Manual de usuario

Leica

Leica GPS System 500 Manual de usuario

Leica

Leica GPS1200 Series Manual del producto

Leica

Leica T-Scan5 Manual de usuario

Leica

Leica MojoMINI Manual de usuario

Leica

Leica MX400 Manual de usuario

Leica

Leica GPS500 Manual de usuario

Leica

Leica GPS1200+ Manual del producto

Leica

Leica T-Scan 5 Manual de usuario

Leica

Leica mojo3D Manual de usuario

Leica

Leica GS09 Manual de usuario

Leica

Leica GPS1200 Series Manual de usuario

Leica

Leica MojoMINI Manual de instalación y funcionamiento

Leica

Leica iNEX Manual de usuario

Leica

Leica GPS1200 Series Manual de usuario

Leica

Leica GS20 Manual de usuario

Leica

Leica MK8 Manual de usuario

Leica

Leica GPS1200+ Instrucciones de uso

Leica

Leica MojoMINI Manual de usuario

Leica

Leica SR20 Manual de usuario

Leica

Leica DistoX2 Manual de usuario

Leica

Leica apMK12 Manual de usuario

Manuales populares de GPS de otras marcas

Raven

Raven Cruizer II Manual

Hama

Hama 53118 Manual de usuario

Garmin

Garmin SOUNDER 125 Manual de usuario

Garmin

Garmin DEZL 580 Manual de usuario

Jigabot

Jigabot EX Manual de usuario

Pointer

Pointer Cellocator CelloTrack XT LTE Guía de instalación

Queclink

Queclink GV55LITE Manual de usuario

Voxson

Voxson Voxtrack GPS500 Manual de instrucciones

Garmin

Garmin ECHOMAP PLUS Manual de usuario

Starcom Systems

Starcom Systems Kylos Compact Manual de usuario

Garmin

Garmin 15 H Series Manual de usuario

Cobra

Cobra Marine MC 600Ci Manual de usuario

Cellocator

Cellocator CelloTrack T Manual de usuario

Enfora

Enfora Mini-MT GSM2228UG001 Manual de usuario

Magellan

Magellan eXplorist 100 Manual de usuario

LTE

LTE G50B Manual de usuario

Garmin

Garmin DEZL OTR500 Manual de usuario

SkyGolf

SkyGolf SkyCaddie SG1 Manual de usuario