LEGRAND radiant Manual de usuario
Smart Plug-In Outdoor
Switch, Wi-Fi
Switch, Wi-Fi
before you start
Review this guide in its entirety. Consult an electrician with any questions or if
you are unsure of your abilities.
Caution: To reduce the risk of injury and/or overheating and damage to
other equipment:
• Connect the smart plug-in switch to a 120 VAC, 60 Hz power source ONLY.
• To reduce the risk of electric shock, this equipment has a grounding type
plug that has a third (grounding) pin. This plug will only fit into a grounding
type outlet. If the plug does not fit into the outlet, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
• Before installation, ensure there is sufficient Wi-Fi signal strength of at
least two bars. Using a smartphone or tablet on the same Wi-Fi network,
go to the device intended location and check signal. If signal is weak, you
may need a Wi-Fi Extender.
For installation support visit:
www.legrand.us/radiant/smart-lighting/support.
general
Legrand’s Smart Plug-In Outdoor Switch with GFCI function provides personal
ground fault protection. Conventional over-current protection devices such
as fuses and circuit breakers cannot protect people from electrical shock.
Those devices are designed to disconnect the power when currents of several
amperes flow from the hot wire to ground. However, currents as low as a few
milliamperes can be dangerous to normal healthy human beings. One ampere
equals 1000 milliamperes.
Many electrical shocks occur when the path of current flow is from the hot wire
through the metal housing of a defective tool or appliance, through the body of
a human being to the ground. Because of the resistance of the human body to
electrical current flow, the current will be quite low relative to that required to
cause conventional over-current protection devices to function. However, it is
likely to be high enough to cause a painful or possibly lethal electric shock to a
human being.
Legrand’s Smart Plug-In Outdoor Switch is designed to remove power from
the equipment loads when these loads have a potentially lethal ground current
in excess of 6 milliamperes. Normal loads will draw current from the Hot
Conductor (black wire) and return it to the power source through the Neutral
Conductor (white wire). Faulty loads can return some of the current to the power
source through a ground path such as a water pipe, gas pipe, wet floor, third
conductor (green wire), or worst of all, through a person who is in contact with an
extrinsic ground.
The Legrand Smart Plug-In Outdoor Switch’s rugged construction allows it to
be used in outdoor or indoor locations, where ground fault protection is desired.
When energized by actuation of the reset button, it will conveniently supply power
to any power tool or appliance whose load requirement does not exceed rated
voltage and currents.
installation
1|Plug unit into 120 VAC power socket protected by fuse or circuit breaker.
2| With no load connected the unit will automatically become energized and
the indicator will blink green and amber after 10 seconds.
3| Press “Test/Off” button.
4|Verify the lamp indicator changes to blink white and amber
(this step denotes that power is off).
5| Press and release “Reset/On” button for use.
6| Connect the desired load equipment to cord receptacle and operate
equipment normally.
NOTE: All three plugs are controlled together.
setup up your system
aDownload and launch the Smart Lights, Wi-Fi app by Legrand. The app is
available on the App Store or on Google Play.
bConnect your Smart Plug-In Outdoor Switch to your home network by
following the step by step instructions in the app.
cUse the app to control your Smart Plug-In Outdoor Switch.
Google Play and the Google Play logo are trademarks of Google LLC.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
SCAN TO WATCH HOW
TO SET UP THE APP
SCAN TO DOWNLOAD
getting to know your switch
Item Name Description
1 LED Locator Light
• Indicates the current state of the device.
See LED locator Light Explanations for
detail.
2 Off Button • Turns the device off. Also used to test GFCI
function.
3 On Button • Turns the device on. Also used to reset the
GFCI function.
LED LOCATOR LIGHT EXPLANATIONS
LED
Color
State of
Light Explanation
Green Blinking
Amber
Device is attempting to
connect to the network.
Solid White Device is connected to
network and is off.
Solid Green Device is connected to
network and is on.
Solid Red
Device is off due to
ground fault. Determine
fault and press RESET.
1
3
2
warnings
If the GFCI fails to trip when the Test button is pressed (lamp indicator fails to
turn white) or, if the GFCI fails to reset when the Reset button is pressed (lamp
indicator fails to remain green), the device should be replaced.
If the GFCI tests properly without any appliance plugged into it, but trips each
time the appliance is plugged in, the appliance has a ground fault and needs
to be repaired or replaced. DO NOT BYPASS THE GFCI. IF THIS CONDITION
OCCURS, A REAL SHOCK HAZARD MAY EXIST.
cautions
1. Do not connect any electrical cord longer than 250 feet to the GFCI output
receptacle in order to avoid possibility of nuisance tripping.
2. This GFCI device is to be used on 120V/60Hz circuit only (such as normal
house-hold electrical distribution system).
3. Ground fault circuit interrupters, whether this device or any other, cannot
protect against electrical shock resulting from contact with both hot and
neutral wires of the electrical circuit nor against defects in any wiring
supplying the device.
4. DO NOT USE IF THE BUTTON BOOTS OR CASE OR CORD HAVE
BEEN DAMAGED.
5. Test frequently and at least before each use of load equipment to ensure
correct operation.
6. The GFCI is designed as a protective device.
7. Do not use on circuit with life support apparatus.
regulatory information
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the transmitter’s radiating structure(s)
and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved
by the manufacturer will void the warranty and the user’s authority to operate
the equipment.
FCC ID: A3LCWAM210S
IC NOTICE
This device complies with Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions: (1) this device may not
cause interference; and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT
This equipment meets the SAR evaluation limits given in RSS-102 Issue 5
requirements at the minimum separation distance of 15 mm to the human body.
Note: Any changes or modifications to this device that are not expressly approved
by the manufacturer, will void the warranty and the user’s authority to operate
the equipment.
IC ID: 649E-CWAM210S
WiFi®is a registered trademark of Wi-Fi Alliance®.
specifications
Load Rating
Resistive 120 VAC, 60 Hz,15 A
Incandescent/halogen 1800 W
Ballast 15 A standard/electronic
Motor ½ HP
LED 5A
Legrand reserves the right to change specifications without notice.
notes
Legrand’s Smart Plug-In Outdoor Switch will provide protection against ground
faults when used with a 2-wire outlet receptacle and a 3-wire to 2-wire adapter.
It is always desirable when possible to use a 3-wire grounded receptacle
because a ground provides additional protection against electrical shock
hazard. The adapter should be of the type that can be grounded to the outer
mounting plate screw.
The GFCI does not sense ground faults in the input conductors, therefore it is
recommended that if any extension cords are used, they should be connected
between the GFCI’s output and the tool or appliance to be powered. Your GFCI is
now ready to test and use.
Otros manuales para radiant
1
Tabla de contenidos
Otros manuales de Cambiar de LEGRAND
LEGRAND
LEGRAND Pro 21 7756 34/47 Manual de usuario
LEGRAND
LEGRAND radiant RCD113 Manual de usuario
LEGRAND
LEGRAND Belanko 617 076 Manual de usuario
LEGRAND
LEGRAND 4 130 09 Manual de usuario
LEGRAND
LEGRAND Niloe LE-764500 Manual de usuario
LEGRAND
LEGRAND Elioflux 766 68 Manual de usuario
LEGRAND
LEGRAND Mosaic 0 770 30 Manual de usuario
LEGRAND
LEGRAND Wattstopper LMSW-610-S Manual de usuario
LEGRAND
LEGRAND Raritan MasterConsole MCD-104-DUAL Manual de usuario
LEGRAND
LEGRAND adorne ASWR155RM Manual de usuario
LEGRAND
LEGRAND Pass & Seymour RRW600V Manual de usuario
LEGRAND
LEGRAND Wattstopper LMSW-210 Manual de usuario
LEGRAND
LEGRAND MY HOME 0 672 35 Manual de usuario
LEGRAND
LEGRAND PlexoTM 0 697 94 Manual de usuario
LEGRAND
LEGRAND The Radiant Collection Manual de usuario
LEGRAND
LEGRAND Mosaic Manageable switch Manual del operador
LEGRAND
LEGRAND Excel Life EM883 Manual de usuario
LEGRAND
LEGRAND PRO 21 7756 11 Manual de usuario
LEGRAND
LEGRAND Raritan Secure Switch Series Manual de usuario
LEGRAND
LEGRAND 4 130 09 Manual de usuario
