LEGRAND In One 495 05 Manual de usuario
Characteristics
LE00226AB
RF individual weatherproof roller shutter switch for
box-mounting
495 05
110 V
230 V
1 x 270 VA
1 x 500 VA
Note: A roller shutter receiver in the box controls a single
motor.
2
Characteristics (cont.)
Safety instructions
RF frequency 868.3 MHz
Range approximately 200 m
in free field
- 20°C to + 65°C
Voltage 100 - 240 VA
Frequency 50 - 60 Hz
Wire section 4 x 0,75 mm2
L
N
Connection
Brown Blue
Grey Black
This product should be installed in line with installation rules, preferably by a
qualified electrician. Incorrect installation and use can lead to risk of electric
shock or fire.
Before carrying out the installation, read the instructions and take account of the pro-
duct’s specific mounting location. Do not open up, dismantle, alter or modify the device
except where specifically required to do so by the instructions. All Legrand products
must be opened and repaired exclusively by personnel trained and approved by Le-
grand. Any unauthorised opening or repair completely cancels all liabilities and the
rights to replacement and guarantees.
Use only Legrand brand accessories.
3
Description
LEARN key LEARN indicator light
Caution:it is advisable to make a note of the ID
number of the weatherproof individual roller
shutter switch before closing the box.
Factory set configuration
When first switched on, the product can be moved
upwards, downwards or stopped by all the shutter general
controls in the installation in factory mode.
This facility is available exclusively to check the correct
functioning of all the opening points.
Pressing the LEARN (1) key twice on the transmitter or
receiver cancels this function.
(1) LEARN: Programming or learning key.
Caution: Before closing the box, it is essential to carry out an initial learning operation to allocate a KEY TRANSMITTER
to the product as it has no local control. This KEY TRANSMITTER cannot by itself erase the controls learnt by the
box-mounted roller shutter receiver.
4
Operation
The individual weatherproof roller shutter switch can be involved in 32 scenarios (2) by local execution of the up, down and
stop controls requested by the transmitters with which it is associated when learning a scenario.
This product can control Venetian blinds when it has learnt a general opening control that directs the slats.
The RF individual shutter switch can also be controlled by a PLC product by using the RF/PLC interface Cat. No. 036 06.
(1) Learning: procedure enabling to define and save a scenario.
This association requires learning of a KEY transmitter priori to closing the housing.
(2) Scenario: set of commands executed simultaneously on the different receivers (actors) that have been associated with
a transmitter (leader) during learning.
5
Operation
L
N
Transmitter
RF group shutter control switch
E.g.: 7756 31 and/or 672 62
Receiver
RF individual weatherproof roller shutter switch for
box-mounting
E.g.: 495 05
6
Operation (cont.)
Caution: Before closing the box, it is essential to carry out an initial learning operation to allocate a KEY TRANSMITTER
to the product as it has no local control. This KEY TRANSMITTER cannot by itself erase the controls learnt by
the box-mounted roller shutter receiver.
Legend
The indicator light
goes out
The indicator light blinks
slowly
The indicator light blinks
rapidly
The indicator light
flashes
Transmitter Receiver(s)
LEARN
indicator
light
LEARN
indicator
light Shutter
Open the
scenario
Learning the KEY TRANSMITTER (mandatory general roller shutter control)
7
Operation (cont’d)
Transmitter Receiver(s)
LEARN
indicator
light
LEARN
indicator
light
Shutter
Save the
scenario
The learning procedure is complete: up, stop, down and slat orientation commands for the shutter connected to the
individual switch will be done by the KEY TRANSMITTER.
8
Operation (cont’d)
Adding a new scenario control by copying the KEY TRANSMITTER scenario
Transmitter Receiver(s)
LEARN
indicator
light
LEARN
indicator
light Shutter
Transmitter to
be added
KEY
TRANSMITTER
9
Operation (cont’d)
Adding a new scenario control by copying the KEY TRANSMITTER scenario (cont.)
Transmitter Receiver(s)
LEARN
indicator
light
LEARN
indicator
light Shutter
To add several transmitters to the scenario, repeat operations 3and 4 for each transmitter (max. 3 transmitters).
Save the scenario
on the KEY
TRANSMITTER
Save the scenario
on the added
transmitter
10
L
N
Operation (cont’d)
Example: changes to the previous general control, by adding an additional individual switch for shutter B.
Receiver
RF individual weatherproof roller
shutter switch for box-mounting
E.g.: 495 05
Transmitter
RF centralised shutter control
switch
E.g.: 7756 31 and/or 672 62
Shutter A
Shutter B
Tabla de contenidos
Idiomas:
Otros manuales de Cambiar de LEGRAND
LEGRAND
LEGRAND 6058 51 Manual de usuario
LEGRAND
LEGRAND 0 226 04 Manual de usuario
LEGRAND
LEGRAND WattStopper RH-200 Manual de usuario
LEGRAND
LEGRAND In One 882 10 Manual de usuario
LEGRAND
LEGRAND 0 672 63 Manual de usuario
LEGRAND
LEGRAND DPX3 Manual de usuario
LEGRAND
LEGRAND 882 10 Manual de usuario
LEGRAND
LEGRAND Arteor 5720 83 Manual de usuario
LEGRAND
LEGRAND 7 521 84 Manual de usuario
LEGRAND
LEGRAND 3 109 53 Manual de usuario
LEGRAND
LEGRAND Wattstopper CS-50 Manual de usuario
LEGRAND
LEGRAND 5 743 12 Manual de usuario
LEGRAND
LEGRAND Pass & Seymour RRW600V Manual de usuario
LEGRAND
LEGRAND 4128 58 Manual de usuario
LEGRAND
LEGRAND Mosaic 782 12 Manual de usuario
LEGRAND
LEGRAND 4771 Manual de usuario
LEGRAND
LEGRAND adorne ASWRRR Manual de usuario
LEGRAND
LEGRAND ELIOT Kit STOP&GO Connected Manual de usuario
LEGRAND
LEGRAND AlphaRex3 DY21 GPS/DCF Manual de usuario
LEGRAND
LEGRAND radiant Manual de usuario
