LEGRAND Wattstopper LMPL-101 Manual de usuario

Wattstopper

Digital Lighting Management Plug Load Controller

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

No: 24045 – 01/19 rev. 3

Catalog Number • Numéro de Catalogue • Número de Catálogo: LMPL-101

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

LMPL-101-U is BAA and TAA compliant (Product produced in the U.S.)

SPECIFICATIONS

Input Voltage .............................................................................. 120VAC, 50/60Hz

Output Capacity............................................................................ 150mA@24VDC

Power Supply ........................................................... Wattstopper Room Controller

Connection to the DLM Local Network.............................................. 3 RJ-45 ports

DLM Local Network characteristics when using LMRC-11x/2xx room controllers:

Low voltage power provided over Cat 5e cable (LMRJ); max current 800mA.

Supports up to 64 load addresses, 24 communicating devices including up

to 4 LMRC-10x series and/or LMPL-101 controllers.

Free topology up to 1,000’ max.

Environment ........................................................................... For Indoor Use Only

Operating Temperature ...........................................32° to 131°F (0° to 55°C)

Storage Temperature ............................................ 23° to 176°F (-5° to 80°C)

Relative Humidity .................................................5 to 95% (non condensing)

Patent Pending

This unit is pre-set for Plug n’ Go™ operation, adjustment is optional.

For full operational details, adjustment and more features of the product, see the DLM System Installation Guide provided with Wattstopper room

controllers, and also available at www.legrand.us/Wattstopper.

Installation shall be in accordance with all applicable regulations, local and NEC codes. Wire connections shall be rated suitable for the wire size

(lead and building wiring) employed.

For Class 2 DLM devices and device wiring: To be connected to a Class 2 power source only. Do not reclassify and install as Class 1, or Power and

Lighting Wiring.

PLACEMENT EXAMPLES

Switch

Ceiling Mount

Occupancy

Sensor

Plug Load

Controller

Line Voltage

(Class 1 wiring)

To Plug Load

(Class 1 wiring)

J-Box

To Other

Electrical

Outlets

Switch

Ceiling Mount

Occupancy

Sensor

Room

Controller

J-Box

Plug Load

Controller

Line Voltage

(Class 1 wiring)

To Plug Load

(Class 1 wiring)

J-Box To Lighting

Load

(Class 1 wiring)

To Other

Electrical

Outlets

Line Voltage

(Class 1 wiring)

MOUNTING THE CONTROLLER

Line

J-Box

Load

J-Boxes

Load

Line

Outside a 4" x 4" box Inside a 4" x 4" box

ATTACHING CABLES

Remove rubber jack covers if using all 3 RJ45 receptacles.

Leave covers in place for all unused receptacles.

CONNECTIVITY

The LMPL-101 communicates with all other DLM devices connected to the DLM local network. Connection drawings are for example

only. The low voltage LMRJ cables can connect to any DLM device with an open RJ45 receptacle.

All line voltage wiring is #12 AWG.

CAUTION: TO CONNECT A COMPUTER TO THE DLM LOCAL NETWORK USE THE LMCI-100.

NEVER CONNECT THE DLM LOCAL NETWORK TO AN ETHERNET PORT – IT MAY

DAMAGE COMPUTERS AND OTHER CONNECTED EQUIPMENT.

Line

Voltage

Room

Controller

Switch

Ceiling Mount

Sensor Low Voltage

DLM Local Network

LMRJ Cables

Plug Load

Controller

LMPL-101

J-Box

120VAC

J-Box

Loads

White: Neutral

Yellow to

Load 2 (B)

LMRC

102

Red: Switched

120VAC Line

Red to

Load 1 (A)

Ground

PLUG N’ GO OPERATION (PNG)

The plug load circuit connected to the LMPL-101 is automatically controlled by all

occupancy sensors on the DLM local network. After the last occupancy sensor’s time

delay expires, or when a switch button bound to the LMPL-100 is operated, the LMPL-101

shuts off the plug load circuit.

Load ON/OFF button

Blue LED ON when

load is ON

UNIT ADJUSTMENT - PUSH N’ LEARN

Load Selection Procedure

Before testing or adjusting the DLM local network load configuration, plug a lamp or radio into one of the electrical outlets on the

controlled plug load circuit.

A configuration button (Config) allows access to our patented Push n’ Learn™ technology to change binding

relationships between sensors, switches and loads.

Step 1 Enter Push n’ Learn.

Press and hold the Config button (on any DLM device) for 3 seconds.

The red LED on the LMPL-101 begins to blink faster (2x per second) as does the red LED on ALL other

communicating devices connected to the DLM local network.

The red LEDs continue to blink until you exit PnL mode. Cong button & red LED

WARNING: TURN THE POWER OFF AT THE

CIRCUIT BREAKER BEFORE WIRING.

All loads in the room turn OFF immediately after entering PnL, then one load will turn ON. This is Load #1, which is bound to switch

button #1 and occupancy sensors as part of the Plug n’ Go factory default setting. All switch buttons and sensors that are bound to

this load have their blue LED solid ON.

Step 2 Load selection.

Press and release the Config button to step through the loads connected to the DLM local network. As each load turns ON note the

devices (switch buttons and sensors) that are showing a bright solid blue LED. These devices are currently bound to the load that is ON.

The blue LED on the room controller or plug load controller connected to the load is also lit.

• To unbind a switch button from a load, press the switch button while its blue LED is ON bright. The blue LED goes dim to indicate

the button no longer controls the load that is currently ON.

• To unbind an occupancy sensor, press the up () or down ()adjustment button while its blue LED is ON. The blue LED turns

OFF to indicate the sensor no longer controls the load that is currently ON.

• Pressing the switch or up () or down () button again while the load is ON rebinds the load to the button or sensor and the blue

LED illuminates brightly.

Step 3 Exit Push n’ Learn.

Press and hold the Config button until the red LED turns OFF, approximately 3 seconds.

TROUBLESHOOTING

Loads do not operate as expected.

LEDs on a switch or sensor

don’t light. 1. Check to see that the the device is connected to the DLM local network.

2. Check for 24VDC input to the device: Plug in a different DLM device at the device location.

If the device does not power up, 24VDC is not present:

• Check the high voltage connections to the plug load controller.

• If high voltage connections are good and high voltage is present, recheck DLM local network

connections between the device and the plug load controller.

The wrong lights and plug

loads are controlled. 1. Configure the switch buttons and sensors to control the desired loads using the Push n’ Learn

adjustment procedure.

LEDs turn ON and OFF, but

load doesn’t switch. 1. Make sure device is not in PnL.

2. Check load connections to room controllers and/or plug load controllers.

800.879.8585

www.legrand.us/wattstopper

No. 24045 – 01/19 rev. 3

Wattstopper warranties its products to be free

of defects in materials and workmanship for a

period of five (5) years. There are no obligations

or liabilities on the part of Wattstopper for

consequential damages arising out of, or in

connection with, the use or performance of this

product or other indirect damages with respect

to loss of property, revenue or profit, or cost of

removal, installation or reinstallation.

Wattstopper garantit que ses produits sont

exempts de défauts de matériaux et de fabrication

pour une période de cinq (5) ans. Wattstopper

ne peut être tenu responsable de tout dommage

consécutif causé par ou lié à l’utilisation ou

à la performance de ce produit ou tout autre

dommage indirect lié à la perte de propriété, de

revenus, ou de profits, ou aux coûts d’enlèvement,

d’installation ou de réinstallation.

Wattstopper garantiza que sus productos

están libres de defectos en materiales y mano

de obra por un período de cinco (5) años. No

existen obligaciones ni responsabilidades por

parte de Wattstopper por daños consecuentes

que se deriven o estén relacionados con el

uso o el rendimiento de este producto u otros

daños indirectos con respecto a la pérdida

de propiedad, renta o ganancias, o al costo

de extracción, instalación o reinstalación.

WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA

Tabla de contenidos

Otros manuales de Controladores de LEGRAND

LEGRAND

LEGRAND Adorne LC7001 Manual de usuario

LEGRAND

LEGRAND 0 488 51 Manual de usuario

LEGRAND

LEGRAND Wattstopper LMPL-111-20M Manual de usuario

LEGRAND

LEGRAND 0 648 84L Manual de usuario

LEGRAND

LEGRAND 0 484 22 Manual de usuario

LEGRAND

LEGRAND EasyIP VADDIO PCC Manual de usuario

LEGRAND

LEGRAND Valena Next Manual de usuario

LEGRAND

LEGRAND Radiant WNRCB40 Manual de usuario

LEGRAND

LEGRAND ALPTEC 5.2 Manual de usuario

LEGRAND

LEGRAND Pass & Seymour LightSense PSHCF Manual de usuario

LEGRAND

LEGRAND 0 884 12 Manual de usuario

LEGRAND

LEGRAND 0 677 886L Manual de usuario

LEGRAND

LEGRAND Galion K8/H251-HK Manual de usuario

LEGRAND

LEGRAND C2G 29977 Manual de usuario

LEGRAND

LEGRAND adorne WNACB40 Manual de usuario

LEGRAND

LEGRAND 0 884 06 Manual de usuario

LEGRAND

LEGRAND 0 884 07 Manual de usuario

LEGRAND

LEGRAND Raritan SRC-0100 Manual de usuario

LEGRAND

LEGRAND Celiane Series Guía de inicio rápido

LEGRAND

LEGRAND 0 648 84L Manual de usuario

LEGRAND

LEGRAND PRO 21 7756 22 Manual de usuario

LEGRAND

LEGRAND Arteor 5 742 74 Manual de usuario

LEGRAND

LEGRAND radiant Manual de usuario

LEGRAND

LEGRAND 0 675 97 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario