Lefroy Brooks M1-4101 Instrucciones de montaje

INSTALLATION, OPERATING & MAINTENANCE INSTRUCTIONS

M1-4101

TWO HANDLE PRESSURE BALANCE ROUGH WITH 2-WAY DIVERTER,

TO SUIT M1-4302 & M1-4303

Contents

Dimensions 3

Instalation Procedure 4

Cartridge Removal & Troubleshooting 6

Parts List 7

Fault Finder 8

Safety Tips, Care and Maintenance 9

Guarantee 10

1/2"-14NPT

3 15/16"

(100mm)

5 1/8"

(130mm) 3 1/16"

(78mm)

6 5/16"

(160mm)

6 1/4"

(158mm)

2 3/4"

(70mm)

5 3/8"

(137mm)

3 1/16"~4 1/16"

(78~103mm)

Dimensions in Inches (& Millimetres)

Whilst every effort is made to ensure accuracy, design and dimensions are subject to change without

notice as part of the company’s product development process.

Stopper A

(marked #049000)

Stopper B

(marked #049001)

Washer C

Dimple on valve stem Notch

Stopper A

(marked #049000) 6

REMOVE CAP ONLY, KEEP THE REST OF

THE MUD GUARD AS IT IS NEEDED TO

HOLD THE TRIM FIXING SCREWS.

Water outlet

Hot water

supply pipe

Cold water

supply pipe

84mm~109mm

Steps 1-6

Installation Procedure

Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.

Shut off main water supply before installation.

1While placing the valve into the wall, make sure that the distance between the wall surface and

the back of the valve is between 84~109mm as the ﬁgure indicates.

2Connect the valve with water pipes.

3Throw away the protective cap only when the building construction is completed and you are

ready to ﬁt the trim kit in.

REMOVE CAP ONLY, KEEP THE REST OF THE MUD GUARD AS IT IS NEEDED TO HOLD THE TRIM

FIXING SCREWS.

4Temperature Limiting Device: Remove washer C, then take off stopper A & B.

5Turn the valve stem so that the round dimple on the stem is at the top side.

6Install stopper A onto valve stem. Notch on stopper A should point upward.

Stopper A

(marked #049000)

Stopper B

(marked #049001)

0 tooth

8 teeth

12 teeth

HIGHT TEMPERATURE SETTING

(with 150° operation range)

AVERAGE TEMPERATURE SETTING

(with 90° operation range)

LOW TEMPERATURE SETTING

(with 60° operation range)

Stopper B

(marked #049001)

Installation Procedure Steps 7-9

Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.

Shut off main water supply before installation.

7Install stopper B. The word “up” should face out.

8Figures I, II, III show how to adjust the temperature limit stop. Having this open at eight notches is

recommended.

9Install washer.

Cartridge (removal)

(A)

(B)

Whenever removing the cartridge always take care to check position o 3-hole rubber gasket (A) which

sits in the inside of the cylindrical recess of the rough (B)

Always remove with with cartridge to prevent accidental loss of this small part.

Problem Cause Action

Water temperature is not adjusting Dirty Balance spool 1. Take out cartridge (making

sure the 3-hole rubber gasket

is not left behind inside the

cylindrical recess of the rough).

2. Turn slot of plastic cover (C) 90

degree anti-clockwise and

remove.

3 Take out the balance

sub-assembly and clean the

pressure balance piston (D)

with a brush and vinegar

water. Then re-install the

piston and the rest of the

sub-assembly into the

cartridge.

(Please make sure the

sub-assembly ﬁts correctly into

the cartridge).

4. re-install the plastic cover into

the cartridge by turning it 90

degree clockwise.

5. Re-install the 3-hole rubber

gasket.

6. Re-install the cartridge.

Cartridge (Trouble-shooting)

(C)

(D)

1 Plaster guard (127212)

2 Screw (075083)

3 Fixing board (126055)

4 Nut (009808)

5 Check valve (507037)

6 Spring (005006)

7 Protective rubber cap (038008)

8 Adjusting ring (104291)

9 Diverter cartridge (507775N)

10 Set screw (075039)

11 Body (076697)

12 O-ring (048017)

13 Adaptor (057838)

14 Body assembly (061847)

15 O-ring (004074)

16 Plug (028599)

17 PB cartridge (507655)

18 Sleeve (041061)

19 Screw (008241)

20 Adjusting ring (104105)

21 Washer (013182)

Parts List Exploded view

Fault Finder

Fault Cause Rectiﬁcation

Too low ﬂow. Check valves not fully open.

Showerheads clogged.

Water pressure from either hot or

cold is too low.

Inspect check valves to ensure they

are fully open/ ﬂush the system.

Remove and clean showerheads.

May need to replace if clogged.

Check for water pressure and adjust

to proper pressure level.

Leaks around handle. Cartridge has come loose or

damaged.

Tighten/reinstall the cartridge or

replacement the cartridge if it is

damaged.

Safety Tips, Care and Maintenance

Safety Tips

If you are soldering during faucet installation,remove cartridges, seats, gaskets and washers prior to

applying ﬂame, otherwise you will void the warranty.

Cover drain openings to avoid losing small parts.

When cutting or soldering pipe, use safety glasses to protect your eyes.

Important Points

Prior to beginning installation. turn off the cold and hot water lines and open the old faucet to release

built-up pressure.

Overtightening nuts may cause damage.

Wrap all threaded connections with pipe tape available at your local plumbing supply store.

Always wrap in a clockwise direction. The ﬁttings should be installed by a state-licenced plumber.

Please note:

When there is a difference in water pressure between hot and cold supplies to the mixing valve, the

pressures should be equalized by a plumber in accordance with best practice and legislation.

Maintenance

Your new bathroom faucet is designed for years of trouble-free performance. Keep it looking new by

cleaning it periodically with a soft cloth. Avoid abrasive cleaners, wire wool and harsh chemicals as

these will dull the ﬁnish and void your warranty.

Routine Maintenance

The frequency and extent of attention required will vary according to prevailing site and operational

conditions, however a 12 monthly maintenance schedule is recommended.

If the product has operated satisfactorily for some time, but performance has been degraded, please

check the Fault Finder section to identify the problem.

Maintenance Check List

 • Wornordamagedsealsandwashers

 • Damagedsealfaces

 • Threadwear

 • Incorrectadjustment

 • Componentfailure

 • Debrisorlimescalebuild-up

Guarantee

Guarantee of Quality

This product is guaranteed against faulty materials and workmanship for 12 months from date

of purchase. For the guarantee to be valid, the unit must be installed by a competent person, in

accordance with the instruction booklet.

Any part found to be defective during the guarantee period, will (at our option) be repaired or

replaced, free of charge, provided the unit has been installed, and properly used in

accordance with the instruction booklet.

Our products correspond to the valid technical and water supply standards as well as the relevant

approvals requirements. We guarantee them to be free of design and production faults at the time

of delivery and that with correct use and care in accordance with our printed instructions they will

function reliably.

Guarantee period

•The guarantee is valid in private homes for 5 years from the purchase date. Proof of purchase

has to be provided when making a guarantee claim.

•By use in commercial or institutional applications the guarantee is valid for 1 year after ﬁrst use.

To make a guarantee claim, proof of purchase or, the beginning of use is required.

Not Covered by this Guarantee

Damage or defects arising from incorrect installation, improper use or lack of maintenance.

Installed product damaged in transit Consequential loss, damage or product removal and installation

costs.

Lefroy Brooks is not responsible for any on site labour charges.

Tabla de contenidos

Otros manuales de Producto de plomería de Lefroy Brooks

Lefroy Brooks

Lefroy Brooks K1-4202 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks M1-1021 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks M2-4300 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks M2-4400 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks M2-4302 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks CW-1010 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks R1-4019 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks R1-4007 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks M1-4200 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks CW-1110 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks X1-2000 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks CB-4626 Manual de usuario

Lefroy Brooks

Lefroy Brooks R1-4003 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks C1-1000 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks MACKINTOSH C1-1103 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks X1-1003 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks M1-1015 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks C1-4602 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks Y1-1069 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks C1-1110 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks K1-4302 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks CB-1401 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks M1-4405 Instrucciones de montaje

Lefroy Brooks

Lefroy Brooks K1-1000 Instrucciones de montaje

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manual

baliv

baliv WT-140 Manual de usuario