Ledj STAGE PAR 64 Manual de usuario

www.prolight.co.uk

STAGE PAR 64

Order code: LEDJ40 (Black)

Order code: LEDJ41 (Polished)

Order code: LEDJ42 (Black)

Order code: LEDJ43 (Polished)

USER MANUAL

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Stage Par 64 Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should nd inside the LEDJ carton the following items:

1, Stage Par 64 Unit 2, Power cable 3, Instruction manual

Technical Specications:

Voltage: AC 230 ~ 50Hz

24 Ultra bright 1W LED’s (R: 8, G: 8, B: 8) - LEDJ40 + LEDJ41

36 Ultra bright 1W LED’s (R: 12, G: 12, B: 12) - LEDJ42 + LEDJ43

Power Consumption: 30W - LEDJ40 + LEDJ41

Power Consumption: 50W - LEDJ42 + LEDJ43

Dimensions: 285 x 223 x 355mm

Weight: 2.5Kg - LEDJ40 + LEDJ41

Weight: 2.7Kg - LEDJ42 + LEDJ43

Operating modes: 1, Static colour mode

2, Colour changing mode

3, Colour fade mode

4, Auto run mode

5, Sound active mode

6, Master/Slave mode

7, DMX mode: 3 & 6 Channel

Overview:

1, DMX input

2, DMX output

3, LED display

4, Fuse (0.5A)

5, Mode selection button

6, Function up button

7, Function down button

Stage Par 64 Technical specications

Operation:

There are 7 different operation modes to choose from:

1) Static colour mode 2) Colour changing mode 3) Colour fade mode

4) Auto run mode 5) Sound active mode 6) Master/Slave mode

7) DMX modes

1, Static colour mode

Mode button - By pressing the “MODE” button under the LED display, the LED display will show

“CL0”, then you can select one of the 7 static colours using the “UP” and “DOWN” buttons. The

Colours range from 1 - 7 and are listed below:

1, Red 2, Green 3, Blue 4, Yellow 5, Cyan 6, Purple 7, White

2, Colour changing mode

Mode button - Press the MODE button until the LED display shows “J00”, then the unit will run in

Colour change mode. Select the speed from 01 - 99 via the “UP” and “Down” buttons.

(01 = Slow, 99 = Fast)

3, Colour fade mode

Mode button - Press the MODE button until the LED display shows “F00”, the unit will then run in

Colour Fade mode. Select the fade speed from 01 - 99 via the “UP” and “Down” buttons.

(01 = Slow, 99 = Fast)

4, Auto Run mode

Mode button - Press the MODE button until the LED display shows “A--”, the unit will then run

in Auto Run mode. The Par Can alternates automatically between colour fade and colour change

modes using the speed that you have previously set by following the instructions above.

5). Sound active

Mode button - Press the MODE button until the LED display shows “S00”, the unit will then run in

Sound Active mode. Select the sensitivity level from 01 - 30 via the “UP” and “Down” buttons.

Please note: The higher the value the more sensitive it will be.

6). Master/Slave mode

Link the units together using a 3-pin DMX cable, then press the MODE button to select one of the

above modes. On the Slave units press the mode button until the LED display shows “SLA”. The

Slave units will then follow in sequence with the Master unit.

7). DMX mode

This unit has two DMX modes for operation. Please see the next page for the DMX chart.

To access the 3 channel DMX mode, press the MODE button until the LED display shows “001.”

To access the 6 channel DMX mode, press the MODE button until the LED display shows “001”

Stage Par 64 Operation

DMX Value/Function

3 Channel DMX Chart

6 Channel DMX chart

Detailed instructions for 6 channel DMX mode.

1). When using channel 1, 2 and 3, for colour mixing you can use channel 5 for the strobe effect.

2). When channel 6 is set to 0-31 and channel 5 is set to 0, you can then use channel 4 to obtain

Colour mixing. ( in this mode channel 1, 2 and 3 have no function)

3). When the value of channel 6 is between 32-223, you can use channel 5 to adjust the speed for

Colour mixing or Colour changing.

4). When the value of channel 6 is between 224-255, you can use channel 5 to adjust the sound

sensitivity to the desired level.

Stage Par 64 Operation

Channel

Value

000-255

Function

RED (0 - 100%)

GREEN (0 - 100%)

BLUE (0 - 100%)

Channel

Value

000-255

0-7

8-255

0-16

17-255

0-31

32-95

96-159

160-223

224-255

Function

RED (0 - 100%)

GREEN (0 - 100%)

BLUE (0 - 100%)

No function

Colour mixing

No function

Strobe/Speed Adjustment/Sound Sensitivity Adjustment

No function

Colour mixing

RGB colour change

7 colour change

Sound activation

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent xtures and controllers. A DMX controller sends DMX data instructions form the

controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the

shortest cable path possible. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Stage Par 64 can be controlled via DMX-512 protocol. The DMX address is set on the back

of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for data

input/output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Stage Par 64 DMX Set up

Further DMX cables can be purchased from all

good sound and lighting suppliers or Prolight

dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

Notice:

• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Stage Par 64 DMX Set up

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de Ledj

Ledj

Ledj LEDJ162 Manual de usuario

Ledj

Ledj STAGE BAR 16 Manual de usuario

Ledj

Ledj Pixel Bar LEDJ73A Manual de usuario

Ledj

Ledj LEDJ387 Manual de usuario

Ledj

Ledj Slimline 1T100 Manual de usuario

Ledj

Ledj STAGE CLOUR QUAD Manual de usuario

Ledj

Ledj Rapid QB1 RGBW Battery Uplighter Manual de usuario

Ledj

Ledj LEDJ02 Manual de usuario

Ledj

Ledj LEDJ377 Manual de usuario

Ledj

Ledj Stage Par CZ 120 RGBA Manual de usuario

Ledj

Ledj FLEX30 Manual de usuario

Ledj

Ledj LEDJ24 Manual de usuario

Ledj

Ledj LEDJ352A Manual de usuario

Ledj

Ledj HEX Par 9 LEDJ226 Manual de usuario

Ledj

Ledj HBR 1D Manual de usuario

Ledj

Ledj Slimline 7HEX6 Series Manual de usuario

Ledj

Ledj LEDJ255 Manual de usuario

Ledj

Ledj HEX Par 9 Manual de usuario

Ledj

Ledj Colour Storm Quad Manual de usuario

Ledj

Ledj Omni Tri-9 Manual de usuario

Ledj

Ledj ECO LED Par 56 Manual de usuario

Ledj

Ledj Mini Pix 4 Batten Manual de usuario

Ledj

Ledj LEDJ225 Manual de usuario

Ledj

Ledj Spectra Par 15Q8 PRO Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario