Ledj LEDJ24 Manual de usuario

www.prolight.co.uk

LED 64 RGBA Can

(Order code: LEDJ24 -Black)

(Order code: LEDJ25 -Polished)

USER MANUAL

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

THIS UNIT ONLY ACCEPTS AN

INPUT VOLTAGE OF 240V

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

LEDJ LED RGBA Can Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Do not expose to ammable sources or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should nd inside the LEDJ carton the following items:

1, LEDJ LED RGBA Can 2, Instruction manual

Technical Specications:

DMX channels: 7

400Hz icker free RGBA LEDs

Power supply: AC 240 ~ 50Hz

177 Ultra Bright 10mm LEDs (R: 30, G: 48, B: 54, A: 45)

Power Consumption: 25W

Beam angle: 25 degrees

Dimensions: 290 x 230 x 220mm

Weight: 2.0kgs

Operating modes: 1, Static Colour mode

2, Colour change mode

3, Colour Fade mode

4, Auto Run mode

5, Slave mode

6, LED mode

7, Sound active mode

8, DMX mode

LEDJ LED RGBA Can Technical specications

Overview:

1, DMX input

2, DMX output

3, LED display

4, Fuse (0.5A)

5, Mode selection button

6, Set up button

7, Function up button

8, Function down button

1, Static colour mode

Mode button - Press the “MODE” button under the LED display, to show “C000”, then press the

“ENTER” button to choose one of the static colours using the “UP” and “DOWN” buttons.

1, “C100” = R, 2, “C200” = G, 3, “C300” = B, 4, “C400” = A, 5, “CF00” = Strobe

Now press the “ENTER” button again and you can then select the output brightness using the

“UP” and “DOWN” buttons. The light output settings are from 00-99 (00 = off, 99 = full)

2, Colour change mode

Mode button - Press the MODE button until the LED display shows “JU00”, then press the

“ENTER” button to choose one of the colour changing modes using the “UP” and “DOWN” buttons.

1, “JU00” = RGBA (15 colours), 2, “JF00” = Strobe,

Now press the “ENTER” button again and you can then select the colour change speed using the

“UP” and “DOWN” buttons.

3, Colour fade mode

Mode button - Press the MODE button until the LED display shows “F000”, then press the

“ENTER” button to choose one of the colour fading modes using the “UP” and “DOWN” buttons.

1, “FA00” = RGBA (15 colours), 2, “FF00” = Strobe,

Now press the “ENTER” button again and you can then select the colour fade speed using the

“UP” and “DOWN” buttons.

4, Auto Run mode

Mode button - Press the MODE button until the LED display shows “AUTO”, the unit will now run

through it’s built-in programmes.

5, Slave mode

Link the units together using a 3-pin DMX cable, then press the MODE button to select one of the

above modes. On the Slave units press the mode button until the LED display shows “SLAV”. The

Slave units will then follow in sequence with the Master unit.

6, LED mode - Use this mode to switch the LED display On and Off

7, Sound active mode

Mode button - Press the MODE button until the LED display shows “SU00”, then press the

“ENTER” button to set the desired sensitivity level using the “UP” and “DOWN” buttons.

The sound sensitivity levels are from 00-99 (00 = low, 99 = high)

8), DMX Addressing mode

To access the DMX address mode, press the MODE button until the LED display shows “A001”,

then press the “ENTER” button and set the rst digit in the DMX address using the “UP” and

“DOWN” buttons. Now repeat this step to set the second and third digits for the desired DMX

address setting. Follow the DMX channel assignment and function table overleaf.

Note: The speed settings for operation modes 2 and 3 are from 00-99 (00 = slow, 99 = fast)

The strobe speed settings for operation modes 1, 2 and 3 are from 00-99 (00 = slow, 99 = fast)

LEDJ LED RGBA Can Operation

7 Channel DMX chart

LEDJ LED RGBA Can DMX Chart

Channel

Value

000-255

0-4

5-80

81-150

151-255

Function

Master dimmer

Strobe

Red (0 - 100%)

Green (0-100%)

Blue (0-100%)

Amber (0-100%)

No function

Colour Macro

Colour change

Colour fade

www.prolight.co.uk

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de Ledj

Ledj

Ledj Spectra Q40 MKII Manual de usuario

Ledj

Ledj STAGE PAR 64 Manual de usuario

Ledj

Ledj Libretto Mini RGBAL Profile Manual de usuario

Ledj

Ledj LEDJ02 Manual de usuario

Ledj

Ledj LEDJ266 Manual de usuario

Ledj

Ledj Event Panel Manual de usuario

Ledj

Ledj Spectra QX40 Pixel MKII Exterior Fixture Manual de usuario

Ledj

Ledj Slimline 7HEX6 Series Manual de usuario

Ledj

Ledj LEDJ112 Manual de usuario

Ledj

Ledj Omni Tri-9 Manual de usuario

Ledj

Ledj STRATOS SPOT Manual de usuario

Ledj

Ledj FLEX30 Manual de usuario

Ledj

Ledj LEDJ254 Manual de usuario

Ledj

Ledj Spectra Par 15Q8 PRO Manual de usuario

Ledj

Ledj STAGE CLOUR QUAD Manual de usuario

Ledj

Ledj Spectra Par 30Q8 PRO Exterior Fixture Manual de usuario

Ledj

Ledj STRATOS Manual de usuario

Ledj

Ledj Spectra Batten LEDJ76 Manual de usuario

Ledj

Ledj SPECTRA PAR 7T3 Manual de usuario

Ledj

Ledj Stage Par CZ200 Dual White Manual de usuario

Ledj

Ledj TRI LED-56 CAN Manual de usuario

Ledj

Ledj LED RGB 252 Manual de usuario

Ledj

Ledj LEDJ225 Manual de usuario

Ledj

Ledj LEDJ P85 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario