Laserworld HIGH PRO-OEM Manual de usuario
HIGH PRO-OEM
OEM housing without laser sources
USER MANUAL
USER MANUAL: Laserworld Mo ing Head HIGH PRO-OEM
Date: 09/2010
Page
2
of
12
Please read this manual carefully before use!
I
Table of contents
Page
1. SAFETY INSTRUCTIONS 3
2. OPERATING THE LASER 4
3. DESCRIPTION 5
4. OPERATE PANEL 6
5. DMX512 OPERATION 7
6. MAINTENANCE 8
7. TECHNICAL SPECIFICATIONS 8
8. ELECTRICAL DRAWING 9
9. PROBLEM AND ANSWER 10
10. APPENDIX ILDA PINOUTS 11
11 EU DECLARATION OF CONFORMITY 12
hecking Parts
Please check if the following parts are included:
1 x HIGH PRO-OEM Laser
1 x Power cable
1 x User manual
USER MANUAL: Laserworld Mo ing Head HIGH PRO-OEM
Date: 09/2010
Page
3
of
12
SAFETY INSTRU TIONS
If the de ice has been exposed to great temperature changes, do not switch it on
immediately. Condensation water may damage your de ice. Lea e the de ice
switched off until it has reached room temperature.
The laser must only be used for shows. Any operation has to be attended and
super ised by a skilled and well-trained operator.
Ne er lea e this de ice running unattended and keep it away from children and
unauthorized persons.
Keep away from heaters and other heat sources. In order to safeguard sufficient
entilation, lea e 50 cm of free space around the de ice.
Ne er direct the laser beam to people or animals.
CAUTION LASER DIODE: If you open the de ice for cleaning, always disconnect from
mains!
-HEALTH HAZARD! Never look directly into the light source, as
sensitive persons may suffer an epileptic shock!
These lasers are considered a definite eye hazard,
particularly at the higher power le els, which WILL cause
eye damage. So these laser series models supplied with a
key switch to pre ent unauthorized use, warning labels
and aperture labels affixed to the laser.
Installation safety
Prior to installation and operation of the laser, the paths of the
beams and effects should be considered, particularly with
respect to how they will reach the audience. If direct audience scanning is desired, then the
laser energy in the effects needs to be considered to decide if the effects are safe for direct
iewing. Always ensure, that the maximum permissible exposure (MPE) is not exceeded in
the area accesible to the public. So install the laser in such a way, that minimum distances
and heights ensure the MPE is ne er exceeded in the public area.
OPERATING THE LASER
The operator has to make sure that laser radiation – also reflected laser radiation – higher
than the maximum permissible le el is a oided by technical or organisational measures.
(Especially with respect to the MPE, see abo e.)
Make sure to use the correct oltage
If the de ice is used in a flying installation, the mounting brackets and an appropriate safety-
rope must be fixed.
In some countries, the operator must notify the accidence insurance and the authority for
industrial safety, before operating a laser. For more information, contact the rele ant
authorities.
Please consider that unauthorized modifications on the de ice are strictly forbidden due to
safety reasons!
If this de ice will be operated in any way differently than described in this manual, the
product may suffer damages and the guarantee becomes oid. Furthermore, any other
operation may lead to dangers like short-circuit, burns, electric shock, etc.
Keep surrounding dry and clean. This unit should be keep dry, do not use in the rain or
damp and dusty en ironment. Projector should be put in a water-proof housing when
operated outside.
Regularly open the de ice (see “cleaning” further down) to check for dust inside, or if fog
fluid condenses in the housing (if so rearrange hazer and/or laser position).
USER MANUAL: Laserworld Mo ing Head HIGH PRO-OEM
Date: 09/2010
Page
4
of
12
Operating temperature is 10~35°C. In a new installation, check after some 15-30 minutes
whether the outlet air gets too warm. Regularly check the inside for dust deposits, especially
around the fans. Let laser cool off 10minutes after 2 hours of operation,to ensure maximum
lifetime for the diode.
Distance between laser aperture and projection screen should be not less than 1 meter.
Do not turn de ice on and immediately off again frequently.
Do not look into the laser beam directly, especially not with optical instruments.
Do not touch the de ice with wet hands.
When the laser diode becomes dim or broken, please contact your dealer timely.
When returning laser to dealer/manufacturer always use original packaging.
Maintenance should be performed e ery 15-day period. See “cleaning” further down.
USER MANUAL: Laserworld Mo ing Head HIGH PRO-OEM
Date: 09/2010
Page
5
of
12
USER MANUAL: Laserworld Mo ing Head HIGH PRO-OEM
Date: 09/2010
Page
6
of
12
USER MANUAL: Laserworld Mo ing Head HIGH PRO-OEM
Date: 09/2010
Page
7
of
12
5. DMX 512 operation
The de ice is controlled by 24 DMX channels. The customized ersion is equipped with a
memory (SD) ILDA playback card. Channel 6 switches between the internal control and the
ILDA playback card.
Channel
Value
Internal
SD C
ard
1
0..255
Pan
Pan
2
0..255
Pan fine
Pan fine
3
0..255
Tilt
Tilt
4
0..255
Tilt fine
Tilt fine
5
0..252
Pan&tilt speed
Pan&tilt speed
253..255
Reset
Reset
6
0..127
Switc
h to intern
al
128..255
Switch to SD card
7
0..255
Bank
Bank
8
0..255
Pat
tern
Frame
9
0..255
Size
Size
10
0..255
Colourgroup
Colourgroup
11
0..255
Intensity blue
Intensity blue
12
0..255
Intensity green
Intensity green
13
0..255
Intensity red
Intensity red
14
0..255
Master intensity
Master intensity
15
0..255
V
-
roll
V
-
ro
ll
16
0..255
H
-
roll
H
-
roll
17
0..255
Z
-
roll
Z
-
roll
18
0..255
V
-
mo e
V
-
mo e
19
0..255
H
-
mo e
H
-
mo e
20
0..255
V
-
stretch
V
-
stretch
21
0..255
H
-
stretch
H
-
stretch
22
0..255
HV
-
stretch
HV
-
stretch
23
0..255
Drawspeed
Drawspeed
24
0..255
Pointspeed
Point
speed
USER MANUAL: Laserworld Mo ing Head HIGH PRO-OEM
Date: 09/2010
Page
8
of
12
6. MAINTENAN E
Always disconnect from mains before cleaning/opening the laser. Remo e the co er of the
mo ing head, and the top co ers of the base to perform cleaning.
Regularly clean the interior from dust, especially ensure operation of the fans. To clean the
mirrors, ideally use acetone and lens cleaning paper (fold paper to get an edge with which to
clean the mirrors). If not a ailable, you can also use window cleaner, and a paper towel. Be
careful, e en light scratches reduce the output power of the laser; always clean with strokes
in one direction, to minimize the effect of scratches. Mirrors need cleaning, when a “halo” is
noticeable around the beam, or an unusual high amount of diffuse light can be seen inside
the de ice.
When fog fluid condenses in the de ice, clean all traces, and rearrange the position of hazer
and/or laser.
Never look directly into the light source.
Always disconnect from the mains when the device is not in use or before
cleaning it.
7. TE HNI AL SPE IFI ATIONS
Power supply: AC 220V-240V, 50/60 Hz
DMX 512: 24 channels
ondition temperature: 10°C ~ +35°C
Input signal bandwidth: 0~1000Hz
X/Y axes beam scanning optical angle: 0 ~ ±30° (max)
Power consumption: 200W
Working mode: ILDA, DMX512, automatic mode (sound, stand-alone programmes)
Weight: 60 kg, 91 kg incl. flightcase
Dimensions: 535 x 510 x 845 mm (L x W x H)
Loudness: <70dB
Errors and omissions expected.
PLEASE NOTE
This de ice has left our premises in absolutely perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessary for the user to follow the
safety instructions and warning notes written in this user manual.
Laserworld cannot be made liable for damages caused by incorrect installations and unskilled
operation!
For ser ice please contact your dealer, or see http://en.laserworld.com/en/reclamation-
ser ice.html. Only use Laserworld spare parts.
USER MANUAL: Laserworld Mo ing Head HIGH PRO-OEM
Date: 09/2010
Page
9
of
12
USER MANUAL: Laserworld Mo ing Head HIGH PRO-OEM
Date: 09/2010
Page
10
of
12
Tabla de contenidos
Otros manuales de Equipo de iluminación de Laserworld
Laserworld
Laserworld GREEN-200A Manual de usuario
Laserworld
Laserworld PL-12.000G Manual de usuario
Laserworld
Laserworld FX Series Manual de usuario
Laserworld
Laserworld GREEN-75E Manual de usuario
Laserworld
Laserworld CS-150G DMX Manual de usuario
Laserworld
Laserworld Ecoline SeriesEL-200RGY Manual de usuario
Laserworld
Laserworld CS-2000RGB Manual de usuario
Laserworld
Laserworld CS-300G DMX Manual de usuario
Laserworld
Laserworld PRO-7000R/640 Manual de usuario
Laserworld
Laserworld MH-OEM Manual de usuario
Laserworld
Laserworld Ecoline Series Manual de usuario
Laserworld
Laserworld CS-200RGY Manual de usuario
Laserworld
Laserworld Proline PRO-800RGB Manual de usuario
Laserworld
Laserworld GREEN-7000 Manual de usuario
Laserworld
Laserworld EL-500RGB KeyTEX Manual de usuario
Laserworld
Laserworld EL-60 G Manual de usuario
Laserworld
Laserworld PL-1200G MH Manual de usuario
Laserworld
Laserworld PL-36000RGB Manual de usuario
Laserworld
Laserworld Evolution ES-800RGB Manual de usuario
Laserworld
Laserworld Garden Series Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
Clas Ohlson
Clas Ohlson GU10 Manual de usuario
