Laserworld PL-12.000G Manual de usuario

Manual / Bedienungsanleitung /

Mode d´emploi

Laserworld Purelight Series

PL-6000RGB | PL-10.000RGB

PL-20.000RGB | PL-30.000RGB

PL-6000G | PL-12.000G

Please spend a few minutes to read this manual fully

before operating this laser!

Bitte lesen Sie diese Bedienungsanleitung sorgfältig

vor Inbetriebnahme dieses Showlasersystems!

Avant d’utiliser cet appareil pour la première fois

nous vous recommandons de lire cette notice d’utilisation!

05/2019

English

Deutsch

Français

Manual: Laserworld Purelight Series

page 2 / 7

Rechtlicher Hinweis:

Die Firma Laserworld (Switzerland) AG behält sich das Recht vor, Änderungen an ihren Pro-

dukten vorzunehmen, die der technischen Weiterentwicklung dienen. Diese Änderungen

werden nicht notwendigerweise in jedem Einzelfall dokumentiert.

Diese Betriebsanleitung und die darin enthaltenen Informationen wurden mit der gebotenen

Sorgfalt zusammengestellt.

Die Firma Laserworld (Switzerland) AG übernimmt jedoch keine Gewähr für Druckfehler, an-

dere Fehler oder daraus entstehende Schäden.

Die in dieser Bedienungsanleitung genannten Marken und Produktnamen sindWarenzeichen

oder eingetragene Warenzeichen der jeweiligen Titelhalter.

Legal Notice:

Thank you for purchasing this Laserworld product.

Due to continual product developments and technical improvements, Laserworld (Switzer-

land) AG reserves the right to make modications to its products.

This manual and its content have been made with due care but Laserworld (Switzerland) AG

cannot however, take any responsibility for any errors, omissions or any resulting damages

forthwith.

The brands and product names mentioned in this manual are trade marks or registered trade

marks of their respective owners.

Information juridique:

L’entreprise Laserworld (Switzerland) AG se réserve le droit d’eectuer des modications con-

cernant leurs produits et ainsi de répondre au développement technique. Ces modications

ne seront pas nécessairement annoncées en tout cas spécique. Ce mode d’emploi et les in-

formations contenues dedans ont été établis avec le soin minutieux qui s’impose dans ce cas.

Laserworld (Switzerland) AG ne pourra pas être tenue responsable pour d’éventuelles erreurs

d’impression ou dommages en résultants. En cas de doutes, veuillez toujours contacter Laser-

world (Switzerland) AG . Les noms de marques et de produits utilisés dans ce mode d’emploi

sont des marques de fabrique ou des marques déposées.

L’utilisation est réservée à un usage professionnel selon décret n°2007-665 du 2 mai

2007 relatif à la sécurité des appareils à laser sortant!

Article 4 bis:

«Les usages spéciques autorisés pour les appareils à laser sortant d’une classe supérieure à 2

sont les usages professionnels suivants: (…)

9° Spectacle et achage:

Toutes les applications de trajectoire, de visualisation, de projection ou de reproduction

d’images en deux ou trois dimensions.»

Manual: Laserworld Purelight Series

page 3 / 7

English

Content:

1. Product and Package Contents

2. Preliminary Warning Notices

3. Initial Operations, Safety Instructions

4. Working on the Device

5. Service Notes

6. Warnings and other Notices on the Device

7. Device & Connections

8. General Operation

9. Operation Modes

10. FB4 Version

Final Statement

Technical Data Sheet

Laser Specications

Manual: Laserworld Purelight Series

page 4 / 7

English

1. Product and Package Contents

Please check if all listed parts are included and undamaged. Included in delivery:

1 x laser projector 1 x key (for key switch) 1 x Interlock connector

1 x power cable 1 x manual

3. Initial Operations, Safety Instructions

1. Make sure to use correct voltage; see in-

formation on device & in this manual.

2. Make sure that the device is not connec-

ted to mains during installation.

3. Installation has to be done by technical

experienced and qualied persons ac-

cording to safety regulations of the res-

pective country.

4. Always ensure that maximum permis-

sible exposure (MPE) is not exceeded

in areas accessible to the public or

members of sta.

5. In some countries an additional ins-

pection by technical control institutes

could be necessary.

6. Connect an easily accessible inter-

lock connector or circuit breaker

to the projector.

7. The power supply should be easily acces-

sible.

8. When installing the laser mount it with

a minimum distance of 15 cm from walls

and objects.

9. For safe setup e.g. on walls or ceilings

please use a safety cord. The safety cord

should be able to withstand tenfold the

weight of the device. Please follow the

accident prevention regulations of pro-

fessional associations and/or comparable

regulations for accident prevention.

10. If the device has been exposed to great

temperature changes, do not switch it

on immediately. Condensation (or any

moisture/water formed) may damage

this device.

11. Never use dimmer, RC or other electroni-

cally switched sockets. Whenever possib-

2. Preliminary Warning Notices

1. Please use this device only according to these operating instructions.

2. Do not use the device if there are any visible damages on housing, connector panels,

power supplies or power cords.

3. Never look directly into the light source of a laser projector. Danger of damage to the

eyes or even blindness in extreme circumstances!

4. This device must not be permanently connected to mains. Disconnect it from mains or

use the power button to switch if o if not in use.

5. Do not operate the device at high humidity or in the rain.

6. Protect device against dripping or splashing water. Do not place any liquid lled con-

tainers near to this device.

Any warranty claims are void if the warranty label is removed or tampered

with in any way.

Manual: Laserworld Purelight Series

page 5 / 7

English

le, do not use the laser projector together

with large appliances (especially fog ma-

chines) on the same mains!

12. Ensure sucient ventilation and do not

place the device on any warm or heat ra-

diating surface. Especially the ventilati-

on openings must not be covered!

13. Ensure that device does not get over-

heated. Make sure that the device is not

exposed to spotlights (especially moving

heads). Heat of spotlights could overheat

laser in a little while and leads to a degra-

dation of performance.

5. Service notes

• Moisture and heat can reduce lifetime of

the laser system dramatically and expires

any warranty claim.

• Quick on/o switching of this device will

reduce durability of the laser diode dra-

matically.

• Avoid sharp knocks and shocks to this

device and ensure sucient protection

during transportation. Look after your La-

serworld product.

• To increase durability of your laser,

protect device against overheating:

-Always ensure sucient ventilation.

-Do not face spotlights (especially mo-

ving heads) to the device.

-Check temperature after approx. 30

minutes with each new installation.

If necessary install the projector at a

place with dierent temperature.

-Keep the device dry. Protect it from

moisture, rain and damp.

-Switch o device when it is not nee-

ded. Diodes are switched on and can

wear out even if there is no visible la-

ser output.

•Removal of the warranty label as well

as damages to the device caused by

improper handling, neglect of the sa-

fety instructions and service notes will

void the warranty.

4. Working on the device

1. This product has no user serviceable parts inside and should

only be maintained and serviced by a qualied engineer.

2. Be sure that the mains plug is not connected to the pow-

er supply while installing the device.

3. Take o all reecting things like rings, watches etc. be-

fore starting to work with or at the projector.

4. Only use non-reecting tools to work on device. Wear pro-

tective clothing (like goggles, gloves etc.) according to laser power and

wavelength of the laser.

Manual: Laserworld Purelight Series

page 6 / 7

English

6. Warnings and other notices on the device

Laser radiation!

Avoid exposure

to beam

Laser radiation!

Avoid exposure

to beam

Laser class 4

Caution of

radiation if co-

ver is removed

Caution of

radiation if co-

ver is removed

Power supply

& consumption

Model type

Wavelength

Output power

Production year

Please read manual before operation

Only for indoor use!

laser radiation

avoid eye or skin exposure

to direct or indirect radiation

class 4 laser product

din en 60825-1: 2015-07

caution of radiation

if cover is removed

7. Device connections / switches

ILDA out

ILDA in

Power button

Fuse

Loop for

safety cord

X/Y inversion

Microphone

sensitivity

MicrophoneScan Safety DIP switches

LAN / ShowNET

Interlock out

Interlock in

DMX out

DMX in

Power in Power out Key switch

Trim pots for color

adjustments

(not available for

PL-6000G &

PL-12.000G)

Manual: Laserworld Purelight Series

page 7 / 7

English

DMX out

DMX in

loop for

safety cord

Interlock

RJ45 for LAN connection to

computer with Pangolin Software

FB4 version

Scan Safety

Trim pots for color

adjustments

(not available for

PL-6000G &

PL-12.000G)

Emission LED

Laser aperture

Beam block

X/Y inversion

buttons

ILDA out

ILDA in Power

connection

Fuse

Power button

key switch

Manual: Laserworld Purelight Series

page 8 / 28

English

8. General Operation

1. Power

Connect the power cord to the device and to the mains. Make sure that your device is pro-

vided with the correct voltage. Wrong voltage could lead to irreparable damages. Please

nd the correct voltage data in the synoptical table at the end of this manual. Make sure

that the device is not directed to people or inammable objects during installation. To

start the device, connect the interlock bridge, insert the key and switch it on, and switch

the device on. The“Emission - Laser on“ LED at the front side of the device begins to

light up when the device is ready for use.

2. Key Switch

There is a key switch at the back of the laser system. Please plug the key to the switch and

turn it on. The laser device only runs when the key is inserted and switched on. Prevent

misuse! Unplug the key when the laser is unattended to prevent misuse of the sys-

tem.

3. Fuse

There is a fuse at the back side of the device. If the fuse should blow, please exchange

it with a new one. If the problems recurs, please contact your dealer or the Laserworld

service department.

4. Safety Presets

This device has an integrated Scan Safety (SFS). Is the Scan Safety active (on), single be-

ams are prevented. If the Scan Safety is switched o, it is possible to create full power

single beams - be careful!

Operating the laser system with disabled SFS may not be allowed in some countries.

Always ensure that maximum permissible exposure (MPE) is not exceeded in areas

accessible to the public or members of sta.

5. X / Y Inversion

Use the X, Y, and/or X/Y buttons to invert the beams resp. patterns on the x-axis and/or

y-axis.

6. Microphone Sensitivity

Set the microphone sensitivity by the‚Sens‘ knob. This setting is needed for music mode

/ sound sensitive operation.

7. Colors (not available for PL-6000G & PL-12.000G)

Use the‚red‘,‚green‘ and‚blue‘ knobs to control the intensity per output color channel.

8. Modes / Functions

The dierent operation modes can be selected with using the DIP switches at the back of

the device. Any change of the operation mode requires a restart of the device (switch

the device o and on again or disconnect power and reconnect it again). Do not change

any DIP switch settings during operation. Random and dangerous laser output can occur.

Manual: Laserworld Purelight Series

page 9 / 28

English

9. Turn device o

To turn o the device, use the power button („OFF“), turn the key to ‚OFF‘ and disconnect

the power cable from the mains.

9. Operation Modes

(Firmware version: 20190520x - Admin tool: v1.33)

This laser system can be operated in many dierent operation modes. It is possible to

directly control the laser system via computer and laser show software as well as to trig-

ger eects stored to the internal SD card via DMX/ArtNet consoles, in stand-alone mode

or in sound-to-light mode. It is also possible to use the laser system as receiver for ILDA

streaming signals from external ShowNET interfaces.

1. Download admin tool

For testing the show laser system and for other purposes, like uploading ILDA les to the

integrated SD card, download the admin tool here:

https://www.laserworld.com/shownet_mainboard

Open the „ShowNET-Admin_Tool.exe“ whenever this manual refers to the admin

tool.

IMPORTANT: It‘s not possible to access the admin tool, when you are accessing the laser

system via software (Showeditor, Showcontroller, etc.). When opening the admin tool

while accessing the laser system in a non-direct-control operation mode, the admin tool

asks to press on a button to switch to network mode for manual control.

2. Direct computer control

a) ILDA control with external DAC interface

The laser system can be controlled via ILDA control signal. There are an ILDA-in (ILDA

input) and an ILDA-thropugh connector at the back side of the device. Connect the laser

system to the control interface (DAC) by using an ILDA cable. Do not connect the laser

to the standard parallel port at the computer, but always use an appropriate ILDA inter-

face. After that the laser can becontrolled by a show laser control software. Use the ILDA-

through connector to daisy-chain the ILDA signal to another laser system.

As this laser system has an integrated DAC interface as mainboard (ShowNET) it is pos-

sible to directly control the laser via LAN without the need of ILDA cables or an external

DAC interface.

b) Direct operation via laser show software, with LAN connection

(1) SHOWEDITOR - free laser show software

This laser system comes with an integrated network interface. The Showeditor laser soft-

ware is included with this ShowNET mainboard for free. It is a full feature laser control

software with LIVE and Timeline control mode and many free laser shows included in

delivery.

Use standard ethernet cable (RJ45 standard) to connect the LAN port of the show laser

system to the computer. Standard network switches can be used to connect multiple

laser systems at once.

Manual: Laserworld Purelight Series

page 10 / 28

English

The software can be downloaded for free on:

https://www.showeditor.com

After downloading and installing the software, open the .exe le on the computer and

use the software to operate the show laser system.

Details on installation and use of the software please nd on the aforementioned web-

site.

(2) SHOWCONTROLLER - professional laser show and multimedia control software

suite

The integrated ShowNET mainboard fully supports the direct control of the laser via

Showcontroller as well. Showcontroller is a mightly software tool with many professional

features. It is very intuitive and thus easy to get started with, too.

The Software and a Demo Version can be downloaded on:

https://www.showcontroller.com

A license can be obtained from where this laser has been purchased.

3. Trigger ILDA les on the internal SD card and own eects

This laser system has an integrated memory (SD card) that can hold ILDA les with laser

frames and animations that can be triggered in dierent ways. It is possible to just use the

standard les that come with delivery or change the les to new, custom ones.

a) Upload own ILDA les to the integrated SD card

Besides the possibility to just upload *.ild les to the SD card with a standard card reader,

it is also possible to remotely load ILDA les to the integrated SD card via LAN without

having to open the device and extract the SD card from the mainboard.

To change the ILDA les, open the admin tool and select the tab‚SD Card‘ as shown in the

picture below:

Select the folder with the ILDA les on the local hard drive by clicking on the button with

the three points on it:

IMPORTANT: Custom laser les have to be stored in *.ild format and must be named with

a number from‚000.ild‘ to‚255.ild‘. Each number represents a DMX value on the respective

fader.

To upload *.ild les greater than 6 MB, please use an external card reader. Otherwise the

import may cause problems.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de iluminación de Laserworld

Laserworld

Laserworld GREEN-4000 Manual de usuario

Laserworld

Laserworld BLUE-5000-445 F Manual de usuario

Laserworld

Laserworld BLUE-1500-445 F Manual de usuario

Laserworld

Laserworld GREEN-12000 Manual de usuario

Laserworld

Laserworld PL-5000G Manual de usuario

Laserworld

Laserworld Pro-150B-473 Manual de usuario

Laserworld

Laserworld EL-60 G Manual de usuario

Laserworld

Laserworld Pro-6000 RGB Manual de usuario

Laserworld

Laserworld GREEN-300 Manual de usuario

Laserworld

Laserworld EL-200 RGY Manual de usuario

Laserworld

Laserworld GREEN-150E Manual de usuario

Laserworld

Laserworld FX Series Manual de usuario

Laserworld

Laserworld GREEN-75E Manual de usuario

Laserworld

Laserworld Club Series Manual de usuario

Laserworld

Laserworld GREEN-200A Manual de usuario

Laserworld

Laserworld PL-1200RGB Manual de usuario

Laserworld

Laserworld Club Series Manual de usuario

Laserworld

Laserworld RS 800 G Manual de usuario

Laserworld

Laserworld Diode Series Manual de usuario

Laserworld

Laserworld Ecoline Series Manual de usuario

Laserworld

Laserworld BLUE-3000-445 F Manual de usuario

Laserworld

Laserworld LW25K Manual de usuario

Laserworld

Laserworld RED-5000-640 Manual de usuario

Laserworld

Laserworld CS-4000RGB FX MK2 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario

Silvair

Silvair MESH-CEDRP Manual de usuario