Larson Electronics HALD-24-1X150LED-V3 Manual de usuario

HALD-24-1X150LED-V3

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 1of 4

Low Profile Explosion Proof LED Light

2x2 Lay-In Troffer - Class I, Divisions 1 & 2, Class II Divisions 1 & 2 - Paint Spray

Booth

Instruction Manual

Thank you for your purchase of the Larson Electronics HALD-24-1X150LED-V3.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. THE HALD-24-1X150LED-V3 MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL

CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.

WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,

CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.

RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.

WARNING

TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,

INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL

APPLICABLEELECTRICAL CODES.

TO AVOIDELECTRIC SHOCK:

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING

CONDUCTOR.

TO AVOID EXPLOSION:

•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT

NAMEPLATE.

•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

•ALL FASTENERS SHOULD BE PROPERLY SEATED.

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 2of 4

HALD-24-1X150LED-V3

WARNING

To avoid the risk of fire, explosion,or electric shock, this product should be installed, inspected, and maintained by a

qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

•

Be certain electrical power if OFF before and during installation and maintenance.

•

Luminaire must be connected to a wiring system with an equipment-grounding conductor

To avoid explosion:

•

Make sure the supply voltage is within the luminaires’ voltage rating.

•

Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere.

•

Do not operate in ambient temperatures above those indicated on the Luminaire nameplate.

•

Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

•

Substitution of components may impair suitability for Class I, Division 2, Class II Division I.

•

Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous.

•

Do not let the power cord touch hot surfaces.

•

Do not mount near gas or electric heaters.

•

Equipment should not be mounted in locations and at heights where it will not be subjected to tampering by

unauthorized personnel.

•

The use of accessory equipment is not recommended by the manufacture and may cause an unsafe condition.

•

Do not use this equipment for other than intended use.

The technical data indicated on the luminaire are to be observed.

•

Changes to the design and modifications of the luminaire are not permitted

•

Only genuine replacement parts are to be used when unforeseen maintenance is required. Consult the factory

at www.larsonelectronics.com or an authorized representative.

The Larson Electronics HALD-24-1X150LED-V3 Hazardous Area LED Light Fixture is designed to provide operators with

a powerful and energy efficient alternative to traditional hazardous location luminaries. This LED panel mount fixture is

ETL listed Class I Divisions 1 & 2, Class II Divisions 1 & 2,and is approved for use within paint spray booths. Cree LED

technology and compact design makes this lamp an excellent replacement upgrade option for paint booths and

hazardous locations where flammable chemical/petrochemical vapors are present.

WIRING

Standard pigtail(flying leads) wiring

We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas

where weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50 or 60Hz

except those factory ordered with low voltage 11V to 25V AC/DC.

Warning: Check product label for correct input voltage!

Attach supply line wires to the appropriate light fixture wires as

shown in thediagram 

Secure each pair of wires according to the diagram. Utilize a junction box

or similar device and take precautionary steps for

weatherproofing all connections if installed in a location where water

may come in contact with the unit. Ensure the unit is properly grounded

and that wiring is done according to all local and national electrical/building

codes.

This unit comes preconfigured with cord whip and selected color temp. Once mounted, plug cord into compatible

receptacle with correct voltage. Fixture available in 100-277 Volts AC, 50/60Hz or 11-25 Volts AC/DC and are not

interchangeable. Please check product nameplate for correct voltage!

WARNING: CHECK NAMEPLATE FOR

PROPER VOLTAGE. DAMAGE FROM

IMPROPER VOLTAGE WILL VOID

WARRANTY. FIXTURE AVAILABLE IN

VARIOUS VOLTAGES SELECTED

UPON PURCHASE.

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 3of 4

HALD-24-1X150LED-V3

MOUNTING

This fixture offers recessed panel mounting. Fixture is not intended to be suspended.

1. Make sure power is turned off at the source to the location at

which you are installing the fixture.

2. Remove existing troffer if applicable.

3. Place the troffer in the drop-ceiling or flat surface cut-out. If

utilizing drop ceiling installation, operators may choose to

penetrate the flanges of the fixture to secure to the ceiling.

When installing on flat surface cutouts, operators will be

required to drill holes in the fixture flange to secure the fixture

to the surface. Use minimum of 3/8" anchor bolts to secure the

fixture to flat surfaces. When drilling holes, ONLY drill holes in

the outer flange of the fixture, minimum 2" distance between

LED assembly and drilled holes. Drilling holes for anchor bolts

does not void certification.

4. Using provided wire, run provided wiring harness from the

back of the fixture inside of 3/4" rigid conduit. Secure the 3/4"

conduit to the back of the 3/4" NPT hub provided on the back

of the light fixture. Make remaining electrical connections

within a junction box that is approved for the environment

where the light fixture is being installed. This light fixture is

factory sealed and does not need a seal-off. Refer to wire

diagram. All local and national electrical/building codes must

be followed when installing this fixture in hazardous areas. If

unaware, contact local authority.

5. When complete, ensure voltage matches fixture nameplate

and return power back to the source.

Installation is complete.

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before

performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void

the warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine

checks to be made on a yearly basis. Frequency of use and environment should determine this. It is

recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:

Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric performance.

Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid

cleaner.

3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 4 of 4

HALD-24-1X150LED-V3

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The HALD-24-1X150LED-V3 is designed to provide years of reliable performance. Should the need for replacement

parts arise, please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Tabla de contenidos

Otros manuales de Equipo de iluminación de Larson Electronics

Larson Electronics

Larson Electronics EPL-TL-2X10W-C-PA Series Manual de usuario

Larson Electronics

Larson Electronics EPL-LB-50LED-RT-180B Manual de usuario

Larson Electronics

Larson Electronics HAL-PM-185LED-CPR Manual de usuario

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-IBSC Manual de usuario

Larson Electronics

Larson Electronics EPL-16C-150LED-RT Manual de usuario

Larson Electronics

Larson Electronics EPLC2-HB-150LED-RT-CM Manual de usuario

Larson Electronics

Larson Electronics EPL-SBDL-150RT-48 Manual de usuario

Larson Electronics

Larson Electronics IND-HVAC-ACS-R1-DP-24-2L-XB Manual de usuario

Larson Electronics

Larson Electronics EPL-20W-HID-X12V-347V-GR50 Manual de usuario

Larson Electronics

Larson Electronics IND-AHF-CD-UVC-R1-220V-50C Manual de usuario

Larson Electronics

Larson Electronics LEDLB-4-IR Manual de usuario

Larson Electronics

Larson Electronics VPLHL-7WLED-PC-GR30 Manual de usuario

Larson Electronics

Larson Electronics EPLC2-EMG-HB-150LED-RT Manual de usuario

Larson Electronics

Larson Electronics HAL-RSL Series Manual de usuario

Larson Electronics

Larson Electronics MMLP-1MLED-12P Manual de usuario

Larson Electronics

Larson Electronics GL-9051-F-M Manual de usuario

Larson Electronics

Larson Electronics LEDP5W-60XC-1227 Manual de usuario

Larson Electronics

Larson Electronics ORS-120-8M-4X150W-LED Manual de usuario

Larson Electronics

Larson Electronics EPL-LED-150W-RT-140DB-480V Manual de usuario

Larson Electronics

Larson Electronics EPL-FL26-LED Series Manual de usuario

Larson Electronics

Larson Electronics EPLC2-LED-50W-RT Manual de usuario

Larson Electronics

Larson Electronics WAL-HL-2000W-240V Manual de usuario

Larson Electronics

Larson Electronics EPL-FL1524-25-1523 Manual de usuario

Larson Electronics

Larson Electronics EPL-16C-2X150LED-RT Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario