Larson Electronics EPL-HB-50LED-RT-JB2-6-EPP Manual de usuario

EPL-HB-50LED-RT-JB2-6-EPP

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

50W C1D1 Explosion Proof Low Bay LED Light Fixture

6' SOOW Cord w/ EPP Cord Cap

Instruction Manual

This explosion proof light is designed for illumination of industrial locations. It uses the latest in

solid state lighting technology for long life, low maintenance and high efficiency.

The unique design focuses the light where it is needed, giving improved efficiency over a

conventional HID luminaire.

An internal, universal input, power-factor-corrected switch-mode supply allows it to be used from any

nominal 100-277V AC 50/60 Hz or 11-25 Volts AC/DC power supply (depending on model) without

any variation in light output.

WARNING

To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected

and maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

•Be certain electrical power is OFF before and during installation and maintenance.

•Luminaire must be connected to a wiring system with an equipment-grounding conductor.

To avoid explosion:

•Make sure the supply voltage is within the luminaires’ voltage rating.

•Ensure the marked T rating is less than the ignition temperature of the Hazardous

Atmosphere.

•Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

•Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

For supply connections, use wire rated for at least 110°C

Recommendedmounting height is 10-40 feet.

MOUNTING

Mount fixture with through bolts via predrilled mounting holes on the back

of the fixture.

This fixture offers a variety of mounting options. Mounting options include

ceiling mounting, pendant mounting, wall mounting and cable mounting.

Each mount is interchangeable and can be switched easily from back of

light. Remove the back cover plate to reveal the driver and line wires.

Feed wires through back cover if not already and replace cover plate.

Thread cable and attach the mount to the back cover plate utilizing the

included hardware through the three (3) mounting holes on the back.

Once attached, fixture is ready to be mounted to the surface or conduit.

MOUNTING

HOLES

EPL-HB-50LED-RT-JB2-6-EPP

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

WIRING (see attached wiring diagram)

This unit comes preconfigured with selected voltage, cord cap and beam configuration. Once

mounted, run wire and plug in to correct voltage listed on nameplate. Voltage: Check Nameplate.

Connect Ground to junction box. This fixture is available in two voltage ranges: 100-277 Volts AC,

50/60Hz or 11-25 Volts AC/DC.

Follow all applicable NEC, local, and state electrical codes.

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool

down before performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens

will void the warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend

routine checks to be made on a yearly basis. Frequency of use and environment should

determine this. It is recommended to follow an Electrical Preventive Maintenance Program

as described in NFPA 70B: Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric

performance. Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use

mild soap or a liquid cleaner.

3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions

or contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if

needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

To replace driver, disconnect power running to fixture. Dismount fixture and remove the back cover.

Disconnect bad driver and remove the single screw holding it in place. Place new driver and replace

screw. Connect power cord and route wires as needed. Replace back cover plate.

WARRANTY

Should further information not covered by these instructions be required, please contact Larson Electronics at

1-800-369-6671 or sales@larsonelectronics.com for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

WARNING: CHECK NAMEPLATE

FOR PROPER VOLTAGE. DAMAGE

FROM IMPROPER VOLTAGE MAY

VOID WARRANTY.

Tabla de contenidos

Otros manuales de Equipo de iluminación de Larson Electronics

Larson Electronics

Larson Electronics IND-HVAC-DTW-XX-SP0108-120W Manual de usuario

Larson Electronics

Larson Electronics GL-2051-F-M Manual de usuario

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-480V-IBSC Manual de usuario

Larson Electronics

Larson Electronics EPL-16C-2X150LED-RT Manual de usuario

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-1L Manual de usuario

Larson Electronics

Larson Electronics WAL-C-4XM Manual de usuario

Larson Electronics

Larson Electronics PML-15 Manual de usuario

Larson Electronics

Larson Electronics HALD-48-1X100LED Manual de usuario

Larson Electronics

Larson Electronics IND-DHA-FUVC-EX-48-3L-V2 Manual de usuario

Larson Electronics

Larson Electronics EPL-FL1524-LED Series Manual de usuario

Larson Electronics

Larson Electronics HALD-EMG-24-1X150LED-V3 Manual de usuario

Larson Electronics

Larson Electronics EPL-TL-2X10W-C-PA Series Manual de usuario

Larson Electronics

Larson Electronics EPLC2-48-100LED-AMB Manual de usuario

Larson Electronics

Larson Electronics XLE-UVC-XX-SGKT-2X Manual de usuario

Larson Electronics

Larson Electronics TPM-2XWP60E-10C Manual de usuario

Larson Electronics

Larson Electronics GVP-48-2L-LED-48VDC-R2 Manual de usuario

Larson Electronics

Larson Electronics LEDSB-3XQF12V-1227-WF-3XKT Manual de instrucciones de instalación

Larson Electronics

Larson Electronics EPL-LED-150W-RT-140DB-480V Manual de usuario

Larson Electronics

Larson Electronics HAL-RSL Series Manual de usuario

Larson Electronics

Larson Electronics EXP-LED-1XB-9W Manual de usuario

Larson Electronics

Larson Electronics PTB-1-50FT Manual de usuario

Larson Electronics

Larson Electronics EPL-SL-5X75-12V-TXF Manual de usuario

Larson Electronics

Larson Electronics EPL-48-4L-LED-D-V2-100C Manual de usuario

Larson Electronics

Larson Electronics EPL-120-150-EPP Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario