Larson Electronics ASX-25 Manual de usuario

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

ASX-25

When starting the flashlight for the first time (cold start), it is recommended that user allows

HID to power up to full (40-60 seconds) before powering off again. This allows the lamp time to

achieve a temperature hot enough to vaporize the additives and prevent deposits from forming

on the inner arc chamber walls. When powering up, it is normal for the lamp to “flicker”, this is

the result of the metal salts in the arc chamber vaporizing. You will also see a slight shade of red

and blue. As the light comes to temperature the flickering will subside, the arc will stabilize and

the light output will increase. The Light emitted from the flashlight is a higher Kelvin

temperature (blue in color) than ordinary flashlights. Full light output occurs in 10-15 seconds.

If momentary shut off of the light is needed you can instantly restart the light without worry of

damage or cool down. It is suggested not to “flash” the light, as this will shorten run time and

lamp life.

CHARGING THE FLASHLIGHT

1. Before charging, power off the HID flashlight. It is to remain powered off while charging.

2. Charger stand required to charge EP batteries. Open the rubber waterproof cover

located at the bottom of the light (on end cap), connect the male jack of charger to the

female receptacle of the flashlight.

CAUTION: Use only the supplied flashlight chargers; do not use other chargers as this

will cause battery failure, overheating and possibly explosion.

3. Connect the charger plug to AC wall power or the DC power source (if DC charger is

being used).

4. Charging time will be approximately 2.5 hours.

5. When the charge is complete, (indicated by Green LED), unplug the charger from the

power source and disconnect the battery jack from the flashlight. Replace the rubber

cap of the female receptor (on end cap) to prevent water from seeping in.

6. The optional Battery Charger Stand may be used to charge a spare Lithium Battery with

either the AC or DC battery chargers.

NOTE:

When charging for long periods of time, the charger and battery will get hot. This is normal. If

excessive heat or odor is noticed, disconnect the charger immediately.

The charger uses a 2-color LED indicator (Red and Green)

When connecting power, the LED will illuminate Green.

While charging, the LED will illuminate Red.

When fully charged the LED will again illuminate Green.

Do not leave the light or battery on charger past full charge or the overcharge circuit protection

will activate.

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

Please refer to “Overcharge Notice” section, if light fails to ignite after a full recharge.

BATTERY REPLACEMENT

The flashlight is modular in design. Replacement of the lithium battery module is as follows:

1. To remove the battery: Turn off the power and carefully rotate the battery counter

clockwise away from the ballast housing.

2. To replace the battery: Carefully line up the battery with the ballast and rotate the

battery clockwise on to the ballast housing, be careful not to cross thread. Tighten

snugly.

3. DO NOT FORCE OR OVER TIGHTEN as damage will occur and you will void your warranty.

NOTICE:

While replacing the battery, please make sure that your flashlight is in the “OFF”

position; otherwise damage can result to the lithium battery, electronic ballast and

electrical connection between ballast and lamp

LAMP AND BALLAST REPLACEMENT

CAUTION NOTICE: Before replacing lamp, make sure the light is “OFF” for a minimum of 10

minutes or longer to ensure any stored power has dissipated, to avoid electric shock from

stored energy in the ballast, and temperature of lens has cooled enough to avoid being burned

from high temperature.

The lens cap has a “fine thread”. Grasp the lamp-head-housing (serrated edge behind lens

protector), with one and while grasping the lens cap in the other, rotate the lens cap counter

clockwise to access the lamp.

While removing the lens cap, be careful not to drop lens, spacer and lamp to avoid damage.

While installing the lamp module, inspect the rubber O-rings for chaffing or breakage, Replace if

signs of wear. There is a plastic spacer between the lens and the outer reflector. The flat side

faces the lens and the slotted side faces the reflector. Check the rubber seal under the clear

lens for wear or breakage, replace if signs of wear. A dab of silicon lubricant or low mineral

petroleum jelly should be used on the threads of the light head before replacing the lens cap.

Be careful not to cross thread and DO NOT FORCE, or you will void your warranty and your light

will be rendered inoperative.

BATTERY CHARGING NOTICE INFORMATION

A safety circuit is incorporated into the battery to protect from over-charging and rapid

discharging of the Lithium Ion battery. In the event of a rapid discharge, due to short circuiting

the battery or an over charge condition, the internal circuit will trip and render the battery

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

inoperative and will have to be replaced. The charger will indicate a full charge condition

(Green LED), but the battery will not power the light.

Do not short circuit the battery. A short circuit will occur if the electrical contacts (contact rings)

on the inside end of the battery come in contact with each other by metal (such as coins, clips,

pens, keys or necklaces, etc.). This will cause the internal fuse to blow.

The battery and charger are calibrated to sense charge rate and charge capacity. Under normal

circumstances the system works reliably. Excessive temperature, power surges, or shock can

cause the circuits to sense an unstable condition that will cause the internal fuse to blow.

BATTERIES

Batteries can be charged and discharged hundreds of times. When a noticeable drop in battery

performance occurs, it is time to replace the battery module. We recommend changing the

battery once a year depending on usage. Shorter durations may be necessary with extensive

use of the light.

While charger is not in use, disconnect the power supply. Do not leave the battery on the

charger past full charge indication as the charger could sense an overcharge condition if a

power surge occurs. Overcharge can shorten the lifespan of the battery. Before charging, make

sure the power switch is “OFF”.

Only use the charger and battery that was shipped with the light. Do not use other types of

batteries or chargers. To do so will damage the light and void your warranty. Your dealer has

spare batteries and chargers available.

Tabla de contenidos

Otros manuales de Flash de Larson Electronics

Larson Electronics

Larson Electronics FL-LED-STR-51 Manual de usuario

Larson Electronics

Larson Electronics RL-11-LED Manual de usuario

Larson Electronics

Larson Electronics EXP-LED-HL-MSHA Manual de usuario

Larson Electronics

Larson Electronics FL-15-HID Manual de usuario

Larson Electronics

Larson Electronics LE-224 Manual de usuario

Larson Electronics

Larson Electronics EXP-LED-RL-FX5R-199 Manual de usuario

Larson Electronics

Larson Electronics LE-2206-LED Manual de usuario

Larson Electronics

Larson Electronics SLEDB-110V-M Manual de usuario

Larson Electronics

Larson Electronics AEX-20-LED-SA Manual de usuario

Larson Electronics

Larson Electronics ATX-20-SE Manual de usuario

Larson Electronics

Larson Electronics EXPRL-91 Manual de usuario

Larson Electronics

Larson Electronics EXP-LED-FX2R-2M Guía

Larson Electronics

Larson Electronics EXP-LED-FX2-2M Guía

Larson Electronics

Larson Electronics HUL-LED25WRE-CPR-NC Manual de usuario

Larson Electronics

Larson Electronics LE-2317C Manual de usuario

Larson Electronics

Larson Electronics HIDH-3550 Manual de usuario

Larson Electronics

Larson Electronics EXPFL-31 Manual de usuario

Larson Electronics

Larson Electronics ATX-20-SA Manual de usuario

Larson Electronics

Larson Electronics EXP-LED-51 Manual de usuario

Larson Electronics

Larson Electronics NSR-9850 Manual de usuario

Larson Electronics

Larson Electronics EPL-UV-20W Manual de usuario

Larson Electronics

Larson Electronics EXP-TP-RL-1XFX5R Manual de usuario

Larson Electronics

Larson Electronics ATX-20-S Manual de usuario

Larson Electronics

Larson Electronics EXP-LED-RL-FX5R Manual de usuario

Manuales populares de Flash de otras marcas

StreamLight

StreamLight PROPOLYMER 2AA Manual de usuario

StreamLight

StreamLight Stinger Manual de usuario

Silverline

Silverline 994024 Manual de usuario

Gama Sonic

Gama Sonic 23i60065 Manual de usuario

Olympia

Olympia RG580 CREE XM-L2 Manual de usuario

EUFAB

EUFAB 13495 Manual de usuario

OLIGHT

OLIGHT S35 BATON Manual de usuario

Kopp

Kopp Emergency Sensor Light Manual de usuario

YLP

YLP PROFESSIONAL Series Manual de usuario

Light motion

Light motion GoBe Manual de usuario

MOB

MOB MO8622 Manual de usuario

EuroLite

EuroLite KKS-3 Manual de usuario

Carson

Carson 500907010 Manual de usuario

Duracell

Duracell 550 Manual de usuario

Mactronic

Mactronic Black Eye 1300 Manual de usuario

Eurotops

Eurotops 29780 Manual de usuario

MOB

MOB MO8690 Manual de usuario

Pelican

Pelican L1 1930 LED Manual de usuario