Lantronix Xpress-Pro SW 92000 Manual de usuario

Part Number 900-504a 1

May 2007

XPress-Pro SW 92000 Quick Start

This quick installation guide describes how to install and use the hardened compact Ethernet Switch. Capable of operating at temperature extremes of

-34°C to +74°C, this is the switch of choice for harsh environments constrained by space.

Physical Description

The Terminal Block and Power Inputs

DC Terminal Block Power Inputs: There are two pairs of power inputs can be used to power up this media converter. Redundant power supplies

function is supported. You only need to have one power input connected to run the Switch.

DC JACK Power input: 12VDC.

The 10/100BaseTX and 100BaseFX Connectors

The 10/100BaseTX Connections

The following lists the pinouts of 10/100BaseT/TX ports.

Pin Regular Ports Uplink port

1 Input Receive Data + Output Transmit Data +

2 Input Receive Data - Output Transmit Data -

3 Output Transmit Data + Input Receive Data +

4 NC NC

5 NC NC

6 Output Transmit Data - Input Receive Data -

7 NC NC

8 NC NC

The 100BaseFX Connections

The fiber port pinouts

The Tx (transmit) port of device I is connected to the Rx (receive) port of device II,

and the Rx (receive) port of device I to the Tx (transmit) port of device II.

The Port Status LEDs

Functional Description

Meets NEMA TS1/TS2 Environmental requirements such as

temperature, shock, and vibration for traffic control equipment.

Meets IEC61000-6-2 EMC Generic Standard Immunity for

industrial environment.

Support 802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,

full/half-duplex; Auto MDI/MDIX.

100BaseFX: Multi mode SC, ST, VF-45, MT-RJ, or LC type;

Single mode SC or ST type; WDM Single mode SC type.

Support 2K MAC addresses. Provides 96K bytes memory

buffer.

Alarms for power and port failure by relay output.

Operating voltage and Max. current consumption: 12VDC @

0.99A, 24VDC @ 0.55A, 48VDC @ 0.39A. Power consumption:

18.72W Max.

Power Supply: Redundant DC Terminal Block power inputs or

12VDC DC JACK with 124-240VAC external power supply.

Operating temperature ranges from -34℃to 74℃.

Supports Din-rail or panel mounting installation.

LED State Indication

POWER

Steady

Switch is properly connected to power

and turned on.

PWR1

PWR2

(Green) Off

Switch is not connected to power and is

turned off.

FAULT

Steady

1. Power failure occurred.

2. Port failure occurred (when port fault

alarm dip switch is enabled).

FAULT

(Red)

Off

1. Power failure is not occurred.

2. Port failure is not occurred (when port

fault alarm dip switch is enabled).

3. Port fault alarm dip switch is disabled.

10/100TX or 100FX

Steady

A valid network connection established.

LNK stands for LINK.

LNK/ACT

(Green)

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

Steady

Light solid yellow for a port transferring

at 100Mbps.

100

(Yellow)

Off

The port is transferring at 10Mbps If this

LED is dark.

Assembly, Startup, and Dismantling

Assembly: Place the switch on the

DIN rail from above using the slot.

Push the front of the switch toward the

mounting surface until it audibly snaps

into place.

Startup: Connect the supply voltage

to start up the switch via the terminal

block (or DC JACK).

Dismantling: Pull out the lower edge

and then remove the switch from the

DIN rail.

Otros manuales para Xpress-Pro SW 92000

Tabla de contenidos

Otros manuales de Cambiar de Lantronix

Lantronix

Lantronix SESPM1040-541-LT Series Manual de usuario

Lantronix

Lantronix SM24TBT2DPA Manual de usuario

Lantronix

Lantronix SISTP1040-551-LRT Manual de usuario

Lantronix

Lantronix SM24T6DPA Manual de usuario

Lantronix

Lantronix SM24TBT2DPA Manual de usuario

Lantronix

Lantronix EDS4100 Manual de usuario

Lantronix

Lantronix SISPM1040-582-LRT Manual de usuario

Lantronix

Lantronix SUN-PC Manual de usuario

Lantronix

Lantronix SISPM1040-582-LRT Manual de usuario

Lantronix

Lantronix Spider Manual de usuario

Lantronix

Lantronix Xpress-Pro SW 52000 Manual

Lantronix

Lantronix SecureLinx Spider Manual de usuario

Lantronix

Lantronix SM4T4DPA Manual de usuario

Lantronix

Lantronix Xpress-Pro SW 94000 Manual de usuario

Lantronix

Lantronix LFH8-S Manual de usuario

Lantronix

Lantronix SM TAT4X Series Manual de usuario

Lantronix

Lantronix SM12XPA Manual de usuario

Lantronix

Lantronix Xpress-Pro SW 52000 Manual de usuario

Lantronix

Lantronix LMR8TT Manual de usuario

Lantronix

Lantronix 300.000.4000 Manual de usuario

Lantronix

Lantronix SISTG1040-2 2-LRT Series Manual de usuario

Lantronix

Lantronix LSW2F8 Manual de usuario

Lantronix

Lantronix SM8TAT2SA Manual de usuario

Lantronix

Lantronix SISPM1040-384-LRT-C Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario