Lantech IPES-0008A-12V Manual de usuario

Lantech

IPES-0008A-12V

8 10/100TX w/ 8 Booster PoE at/af

Injector Industrial Switch

User Manual

V1.00

Jun 2010

Recommendation for Shielded network cables

STP cables have additional shielding material that is used to reduce external interference. The

shield also reduces the emission at any point in the path of the cable. Our recommendation is

to deploy an STP network cable in demanding electrical environments. Examples of

demanding indoor environments are where the network cable is located in parallel with

electrical mains supply cables or where large inductive loads such as motors or contactors are

in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the

power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

FCC Warning

This Equipment has been tested and found to comply with the limits for a

Class-A digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy. It may cause harmful interference to radio

communications if the equipment is not installed and used in accordance

with the instructions. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Content

Introduction.............................................................. 1

Features................................................................. 1

Technical Specification........................................... 2

Package Contents ................................................. 4

Safety Precaution .................................................. 4

Hardware Description.............................................. 5

Physical Dimension................................................ 5

Front Panel............................................................ 6

Top View................................................................ 6

LED Indicators....................................................... 7

Ports....................................................................... 8

Cabling................................................................... 9

Wiring the Power Inputs ......................................10

Wiring the Fault Alarm Contact...........................12

Mounting Installation..............................................13

DIN-Rail Mounting ................................................13

Wall Mounting.......................................................15

Hardware Installation..............................................16

Installation Steps ..................................................16

Network Application................................................17

Troubleshooting......................................................18

Introduction

IPES-0008A-12V Industrial Switch is a cost-effective solution, which meets the high

reliability requirements demanded by industrial applications, and also supports to

operate in the wide temperature -40°C ~ 75°C environments. Besides, the equipment

supports 12V or 48V DC power input and provides the PoE function with 48VDC

output for kinds of Powered Devices to receive power as well as data over an RJ-45

cable.

Features

System Interface/Performance

RJ-45 ports support Auto MDI/MDI-X Function

Embedded 4-port PoE Injection

Store-and-Forward Switching Architecture

Back-plane (Switching Fabric): 1.6Gbps

2K MAC Address Table

Power Input

DC 12V/48V Redundant Power Input

Operating Temperature

Wide Operating Temperature: -40°C ~ 75°C

Case/Installation

IP-30 Protection

Installation in a Pollution Degree 2 environment

DIN Rail and Wall Mount Design

Provides EFT protection 3,000 VDC for power line

Supports 6,000 VDC Ethernet ESD protection

Technical Specification

The technical specifications of IPES-0008A-12V Industrial Switch are listed as follows.

Communications

Compatibility

IEEE 802.3, 802.3u, 802.3x, 802.3af

LAN

10/100Base-T

Transmission Speed

Up to 100 Mbps

Interface

Connectors

8 x RJ-45 (8-port 10/100TX)

6-pin removable screw terminal (Power & Relay)

LED Indicators

Unit: Power1, Power2, P-Fail, PoE

Ethernet port: Link/Active, Speed

PoE

Power Output

Per port 48 VDC, 15.4 Watts

Pin Assignment

RJ-45 port #1 ~ # 4 support IEEE 802.3af

End-point, Alternative A mode.

Positive (VCC+): RJ-45 pin 1, 2.

Negative (VCC-): RJ-45 pin 3, 6.

Data (1,2,3,6 )

Power

Power Consumption

10 Watts (Max.); POE Power Budget:240 Watts

(48V input); 90W(12V); 120W(24V input)

Power Input

External Power Supply: DC 12~48V, Redundant

power D12V~DC 48V and connective removable

terminal block.

Fault Output

1 Relay Output

Mechanism

Dimensions (WxHxD)

74mm (W) x 115mm (D) x 152mm (H)

Enclosure

IP-30, Metal shell with solid mounting kits

Mounting

DIN-Rail, Wall Mount

Protection

ESD (Ethernet)

6,000 VDC

Surge (EFT for power)

3,000 VDC

Power Reverse

Yes

Overload current protection

Yes

Environment

Operating Temperature

Standard: -20°C~60°C /-4°F~140°F

E models:-40°C~75°C / -40°F~167°F

Operating Humidity

5% ~ 95% (non-condensing)

Storage Temperature

-40 ~ 85oC

Storage Humidity

5% ~ 95% (non-condensing)

Certifications

EMC

FCC Class A

CE EN61000-6-2

CE EN61000-6-4

CE EN61000-4-2 (ESD)

CE EN61000-4-3 (RS)

CE EN61000-4-4 (EFT)

CE EN61000-4-5 (Surge)

CE EN61000-4-6 (CS)

CE EN61000-4-8 (Magnetic Field)

Free Fall

IEC60068-2-32

Shock

IEC60068-2-27

Vibration

IEC60068-2-6

Package Contents

Please refer to the package contents list below to verify them against the checklist.

IPES-0008A-12V Industrial Switch (with DIN-Rail Bracket)

User manual

Removable Terminal Block

Optional Wall-mount Kit** (2 wall-mount bracket with screws)

Compare the contents of the industrial switch with the standard checklist above. If any

item is damaged or missing, please contact the local dealer for service.

Safety Precaution

Attention

IF DC voltage is supplied by an external circuit, please use a protection

device on the power supply input.

Hardware Description

In this paragraph, the Industrial switch’s hardware specs, ports, cabling information, and

wiring installation will be described.

Physical Dimension

IPES-0008A-12V Industrial Switch dimensions (W x D x H) is 48.6mm x 95mm x 140mm,

the detail dimensions as Figure-1

Figure-1: Mechanical Dimensions

Front Panel

The Front Panel of IPES-0008A-12V Industrial Switch is shown below Figure-2

Figure-2: Front Panel of the PoE Injectors Industrial Switch

Top View

The top view of IPES-0008A-12V Industrial Switch has one terminal block connector of

two DC power inputs and Relay circuit contact. Please refer to Figure-3 for further

information.

Figure-3: Top View of the PoE Injectors Industrial Switch

Tabla de contenidos

Otros manuales de Cambiar de Lantech

Lantech

Lantech GE-800 Manual de usuario

Lantech

Lantech IES-3 Series Manual de usuario

Lantech

Lantech IPES-3424DSFP-2P Manual de usuario

Lantech

Lantech IGS-0208GSFP Manual de usuario

Lantech

Lantech IES-2008 Manual de usuario

Lantech

Lantech IPES/IES-0008B Series Manual de usuario

Lantech

Lantech LGS-2424C Manual de usuario

Lantech

Lantech IPES-0005B Series Manual de usuario

Lantech

Lantech IPES-0204DFT-4 Manual de usuario

Lantech

Lantech IPWMR-3204DF Manual de usuario

Lantech

Lantech LGS-2300-RPS Manual de usuario

Lantech

Lantech TES-R6616XFT Manual de usuario

Lantech

Lantech IPGS-3 Series Manual de usuario

Lantech

Lantech IPES-0104FA Manual de usuario

Lantech

Lantech IES-2208CA-DNV Manual de usuario

Lantech

Lantech IPES-3408GSFP Manual de usuario

Lantech

Lantech IES-3208C Manual de usuario

Lantech

Lantech IES-5416DF Series Manual de usuario

Lantech

Lantech IPES-0008B Series Manual de usuario

Lantech

Lantech LGS-2404 Manual de usuario

Lantech

Lantech IPES-0208 Series Manual de usuario

Lantech

Lantech IES-0008B Series Manual de usuario

Lantech

Lantech IPWMR-3006 Manual de usuario

Lantech

Lantech IGS-2404 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario