Lanpro LP-288ai Manual de usuario
Wireless - Equipment
www.lanpro.com
123 Manual, LP-288ai V2.0 TURBO OFDM Compact Outdoor Radio with Throughput Booster,
INSTALLATION IN POINT TO POINT, POINT TO MULTIPOINT MODE WITH FIRMWARE V2.0.3B2P1
LP288aiV23B2_M123_END01W
123 Manual, LP-288ai V2.0
TURBO OFDM Compact Outdoor Radio
with Throughput Booster,
INSTALLATION IN POINT TO POINT,
POINT TO MULTIPOINT MODE
WITH FIRMWARE V2.0.3B2P1
www.lanpro.com
Wireless - Equipment - 123 Manual - LP-288ai V2.0 TURBO OFDM Compact Outdoor Radio
with Throughput Booster. Installation in Point to Point, Point to Multipoint Mode with rmware V2.0.3B2P1
2
1
AP A AP B
2
Go to the properties of your network card, select Internet Protocol
(TCP/IP), and then select Properties, as shown in Figure 1.
Select Use the following IP address and type an
IP address in the LP-288ai IP range by default. For
this example we have selected the 192.168.1.201
address, The LP-288ai has the 192.168.1.20 address
by default. In Subnet mask type 255.255.255, as
shown in Figure 2. Once you have nished, select
OK twice.
Figure 1
Figure 2
CONNECTION DIAGRAM
Wireless - Equipment - 123 Manual - LP-288ai V2.0 TURBO OFDM Compact Outdoor Radio
with Throughput Booster. Installation in Point to Point, Point to Multipoint Mode with rmware V2.0.3B2P1
www.lanpro.com
3
For this conguration you will need the MAC Addresses of the Access Points you are going to use for point to
point connection. You will also use two different IP addresses in the range for their management.
In order to verify the MAC Addresses you shall access each LP-288ai and check it in System Status window. To do so:
Figure 3a-1 Figure 3a-2 Figure 3a-3
b. Connect the cable as shown in Figure 3b.
c. Connect the POE as shown in Figure 3c.
Figure 3b
Figure 3c
a. Prepare the cable with the connector, as shown in Figures 3a-1, 3a-2, and 3a-3.
3
www.lanpro.com
Wireless - Equipment - 123 Manual - LP-288ai V2.0 TURBO OFDM Compact Outdoor Radio
with Throughput Booster. Installation in Point to Point, Point to Multipoint Mode with rmware V2.0.3B2P1
4
f. Open the web browser of your preference and type the default address 192.168.1.20, as shown in Figure 3f.
Figure 3f
d. Connect your PC or switch to the LP-288ai POE, as shown
in Figure 3d.
Figure 3d
e. Connect to electric power, as shown in Figure 3e.
Figure 3e
Wireless - Equipment - 123 Manual - LP-288ai V2.0 TURBO OFDM Compact Outdoor Radio
with Throughput Booster. Installation in Point to Point, Point to Multipoint Mode with rmware V2.0.3B2P1
www.lanpro.com
5
Figure 3h
Figure 3i
Figure 3g
g. The equipment will request a user and a password. The
LP-288ai has two user levels, one with all the privileges, which
is super by default with super as password, and another with
fewer privileges with admin as user and admin as password.
Type super in user and password and select OK, as shown in
Figure 3g.
h. In the initial window (System Status), take
note of the MAC Address of the rst equipment, as
shown in Figure 3f. Repeat this procedure with the
second LP-288ai (From step ato h).
i. Reconnect the rst equipment and proceed to access it. To do so, open the web browser of your preference and type
the default address 192.168.1.20, as shown in Figure 3i.
www.lanpro.com
Wireless - Equipment - 123 Manual - LP-288ai V2.0 TURBO OFDM Compact Outdoor Radio
with Throughput Booster. Installation in Point to Point, Point to Multipoint Mode with rmware V2.0.3B2P1
6
4
Proceed to change the IP of AP A, which will be
192.168.1.2 according to the diagram. To do so, select
IP Conguration, type 192.168.1.2 in IP Address
box and click on Update, as shown in Figure 4.
To make changes effective select Reboot, as shown
in Figure 5.
A progress bar indicating that the equipment is
rebooting will be displayed, as shown in Figure 6.
Figure 6
AP A
5
6
Figure 4
Figure 5
Wireless - Equipment - 123 Manual - LP-288ai V2.0 TURBO OFDM Compact Outdoor Radio
with Throughput Booster. Installation in Point to Point, Point to Multipoint Mode with rmware V2.0.3B2P1
www.lanpro.com
7
8
9
7
Figure 7
Figure 8
Figure 9
Select Basic/Operation Mode and then Access
Point in Operation Mode. Enter the network name
in the SSID eld and select the channel in Radio
Frequency eld, which will depend on the existing
links and/or interferences (See Appendix 1), and
check Suppress SSID to hide it. Additionally, we
recommend you to adjust the distance in Distance
option (See Appendix 2). Select Update, as shown
in Figure 7.
The equipment will save changes, but they won´t
be effective unless you reboot it. Select Reboot,
as shown in Figure 8.
A progress bar indicating the equipment is rebooting
will be displayed, as shown in Figure 9.
www.lanpro.com
Wireless - Equipment - 123 Manual - LP-288ai V2.0 TURBO OFDM Compact Outdoor Radio
with Throughput Booster. Installation in Point to Point, Point to Multipoint Mode with rmware V2.0.3B2P1
8
10
Figure 10
Figure 11
Figure 12
Proceed to add the MAC Address of the Access Point B
(the second LP-288ai) in Basic/Remote AP List. To
do so, select Remote AP List, add the MAC Address
of the AP B in MAC Address eld and enter the priority
for point to point links (we recommend priority 1).
Select Add/Update, as shown in Figure 10.
11
Once you have saved the changes, you must
select Reboot so they will be effective, as shown in
Figure 11.
A progress bar indicating that the equipment is
rebooting will be displayed, as shown in Figure 12.
12
Wireless - Equipment - 123 Manual - LP-288ai V2.0 TURBO OFDM Compact Outdoor Radio
with Throughput Booster. Installation in Point to Point, Point to Multipoint Mode with rmware V2.0.3B2P1
www.lanpro.com
9
13
Select the authentication method, which is Shared
Key for this example. Select the key entry method,
in this case Ascii Text, enable Key 1, type it in
Encryption Key, and select its length in Key Length
(128 bit) in this case. Select Update to save changes,
as shown in Figure 14.
Select Reboot so the changes will be effective, as
shown in Figure 15.
Select Advanced/Security Setting and in Security
Mode select the WEP encryption mode, as shown
in Figure 13. It is important to mention that in PtP
mode this is the only security mode permitted.
Figure 14
14
15
Figure 15
Figure 13
www.lanpro.com
Wireless - Equipment - 123 Manual - LP-288ai V2.0 TURBO OFDM Compact Outdoor Radio
with Throughput Booster. Installation in Point to Point, Point to Multipoint Mode with rmware V2.0.3B2P1
10
A progress bar indicating that the equipment is
rebooting will be displayed, as shown in Figure 16.
Proceed to add the AP B MAC Address in Advanced/
MAC Addr Control to limit the connection to this
equipment only the LP-288ai B. Select MAC Addr
Control and check Enable, add the AP B MAC Address
and select Add, as shown in Figure 17.
Observe how the access of the MAC Address is allowed.
Select Update, as shown in Figure 18.
16
17
18
Figure 16
Figure 17
Figure 18
Otros manuales para LP-288ai
3
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de Lanpro
Lanpro
Lanpro LP-1540ai Manual de usuario
Lanpro
Lanpro LP-C290N Manual de usuario
Lanpro
Lanpro LP-570G Manual de usuario
Lanpro
Lanpro LP-C290N Manual de usuario
Lanpro
Lanpro LP-C290N Manual de usuario
Lanpro
Lanpro LP-1522 Manual de usuario
Lanpro
Lanpro LP-1540ai Manual de usuario
Lanpro
Lanpro LP-5A Manual de usuario
Lanpro
Lanpro LP-1540ai Manual de usuario
Lanpro
Lanpro LP-289ai Hoja de instrucciones
