Laguna Tools MTST5S-0135 Manual de usuario

17101 Murphy Avenue. Irvine, California 92614 www.lagunatools.com 800.234.1976

MTST5S-0135

OPERATING MANUAL

T5S TABLESAW

Table of Contents

8. WIRING DIAGRAMS

1. INFORMATION P1

2. MACHINE INFORMATION P6

3. ASSMBLY & SET UP

3-1. Setup safety……………………………………….………………..……………………................

3-2. Unpacking………………….……….…………………………………………………………………….

3-3. Extension table…………………………….…………………………………………………………..

3-4. Rip fence……………………………………………………………………………………………………

P11

3-5. Fitting or change saw blade & riving knife…..…………………………………………….

P13

3-6. Fitting or changing the scoring blade…………………………………………………………

P17

3-7. Saw blade guard……..…………………………………………………………………………………

P18

3-8. Accessories………………………………………….……………………………………………………

P19

3-9. Wiring & test run……………………………………….…...………………………………………..

4. OPERATION

4-1. Control panel and hand wheel..……………………..………….……………………………..

P22

4-2. Scoring blade tilting and lifting………………………………………………………………….

P23

4-3. Rip fence cutting……………………………………………………………………………………….

P24

4-4. Miter gauge cutting…………………………….…………………………………....................

P25

5. MAINTENANCE

5-1. Cleaning and checking…………………………….………..……………………………………...

P26

5-2. Lubrication ……………………………………..……….……………………………………………….

P28

5-3. Replacing belt……………………………………………..……….……………………………………

P29

6. TOOLS LIST P31

7. TROUBLESHOOTING P32

. PARTS LIST

ASSEM 1- Machine body & table

ASSEM 2- Control panel

ASSEM 3- Power unit

ASSEM 4- Saw blade angle device

ASSEM 5- Saw blade rise & fall device

ASSEM 6- Scoring device

ASSEM1 - Rip fence

ASSEM12- Saw blade guard

ASSEM14- Accessories

1. INFORMATION

1-2 SAFETY RULES

For your own safety read instruction manual before operating

1) Read instruction anual before operating the achine for your safety.

Person(s) who operate the machine must be trained, read and understood to

use the safety measures, and possess the ability to obey and execute the

regulation stated in this manual. Learn the machine's application and

limitations as well as the specific hazards peculiar to it.

2) Ground all achines.

It should make sure the "PE" terminal being connection before machine

operating.

3) Keep guards in place and working area clean.

Keep guards in place and in working order.

4) Don't use in dangerous environ ent.

Don't use machines in damp or wet locations, or expose them to rain.

Please pro ide a suitable illumination around the machine for safety operation.

5)Keep children and visitors away.

All children and isitors should be kept at a safe distance from work area.

6) Store idle tools (cutting spindle).

When not in use, tools should be store in a dry, high or locked up place, out

of reach of children.

7) Wear proper apparel.

No loose clothing, glo e neckties, rings bracelets, or other jewelry to get

caught in mo ing parts. Wear protecti e hair co ering to contain long hair.

Please wear glove to take/ replace saw blade and wear eye-shield/ ear-shield to

operation.

8) Stay alert.

Watch what you are doing. Do not operate machine when you are tired.

9) Don't force achines.

It will do the job better and be safer at the rate for which it was designed.

10) SHUT OFF the power remo ed the products and isolated energy before lea ing the

machine.

Shut off the power and carried out only when the machine is stationary before

inspection, maintenance, adjustment and cleaning.

11) No s oking!!

Don’t smoking while operate machine.

12) Have your achine repaired by a qualified person.

Repairs should be carried out by qualified-persons using original spare

parts; otherwise this may result in considerable danger to the user.

1. INFORMATION

13) Check da aged parts.

Before further use of the machine, a guard or other part that is damaged

should be carefully checked to determine what it will operate properly and

perform its intended function. Being check for alignment of mo ing parts,

binding of mo ing parts, breakage of parts, mounting and any other

conditions that may affect its operation. A guard or other part that is damaged should

be properly repaired or replaced

14) Disposing of wasted aterial

Disposing wasted material and wasted lubricating oil shall obey the local

regulation and be deeply careful.

15) Fire extinguisher:

Workshop of user shall be with the fire extinguisher or other de ices

according to the local safety regulations and be deeply careful.

16) Stand on proper position for operation.

Please stand in front of machine for operation. Please refer following

drawing.

17) Use reco ended ancillary equip ent.

Consult the instruction manual of drawing for recommended accessories.

The use of improper accessories may cause risk of injury to persons.

If ancillary equipment is remo ed the original guards or safety de ices shall

be replaced.

OAV and our authorized agency are responsible for a future connection of the machine

with ancillary equipment only if we oursel es ha e designed such connection.

18) Reduce the risk of unintentional starting.

Make sure switches of control panel are OFF position before operating.

19) Never leave achine running unattended. Turn power off from the

hand-held disconnecting de ice. Don't lea e machine until it comes to a complete

stop.

20) Make sure achine is disconnected fro power supply:

Make sure machine is disconnected from power supply before started the

normal maintenance and ser ice, adjustment, or repairing.

21) Reaction with e ergency situation:

This machine pro ides two emergency buttons. One is self-latching push-

button on the control panel of access position. Other emergency buttons

are position on the front side on the machine near in-feed working area. The

emergency button is colored red and yellow background. After emergency stop, follow

the normal start up procedure and suitable operation to ob iate the hazard. Please see

the afterward pages of emergency stop position diagram.

1. INFORMATION

22) Ne er open the protecti e co er or the machine door while the machine is running.

23) When the machine is out of order while running, shut it down and to

call ser icemen for help as soon as possible.

24) Wear ear protectors (plugs or muffs) during extended periods of operation.

25) Remo e adjusting keys and wrenches before turning machine on. Be sure that the keys

and adjusting wrenches ha e been remo ed and all the nuts and bolts are secured.

26) After switching off the saw motor, allow the saw blade to stop freely. Ne er attempt to

stop the cutting by hand or other objects.

27) Ne er cut the wood plate if there is no completed width or too small.

28) The max. Rotation speed marked on the saw blade must not be exceeded.

29) The machine shall be not loaded with more than work piece at a time.

30) During making wooden cases, it will emit harmful dust. User must install exhaust

system for the extraction of harmful dust.

31) Use correctly sharpened saw blades. Obser e the max. Speed marked on the saw blade.

User shall be to select the optimum speed for saw blade.

32) Report faults on the machine, including guards or saw blades, as soon as they are

disco ered.

33) Adopt safe procedures for cleaning, maintenance and remo e chips and dust regularly

to a oid the risk of fire.

34) Follow manufacturers’ instructions for use, adjustment and repair of saw blades.

35) Ensure that any spacers and spindle rings used are suitable for the purpose as stated

by the manufacturer.

36) Refrain from remo ing any off-cut or other part of the work piece from the cutting

area whilst the machine is running.

37) Ensure that guards and other safety de ices necessary for machine operation are in

position, in good working order and properly maintained.

38) Safety working practice.

a) Use of push block and push stick- Push stick should be used to a oid working with

hands close to the saw blade. Push blocks should be between 300mm and 400mm

long, 80mm to 100mm wide and 15mm to 20mm deep. Push blocks should be used

when cutting small work pieces and in circumstances where it is necessary to push

the work piece against the fence.

b) Selection of saw blade and ri ing knife- the operator should only select saw blade of

a diameter and thickness suitable for the machine.

c) Selection of ri ing knife slot- The ri ing knife guiding slot should be no more than

0.5mm wider than the ri ing knife guiding elements.

d) Fixing of saw blade to spindle- Where the spindle diameter is less than the saw blade

bore diameter, flanged bushes pro ided by the machine manufacture should be used

1. INFORMATION

to make up the difference. The use of loose rings or bushes is not permitted.

e) Lighting- it is important to pro ide adequate lighting around the machine.

39) Guide the work piece along the rip fence and through the rotation saw blade, using

the push stick if necessary. Any damage, please replace new one that specification

according below drawing.

40) Do not operate this machine while tired or under the influence of drugs, alcohol or

any medication.

41) THE DUST GENERATED BY CERTAIN WOODS AND WOOD PRODUCTS CAN BE

INJURIOUS TO YOUR HEALTH. Always operate machinery in well- entilated areas, and

pro ide for proper dust remo al. Use wood dust collection systems whene er

possible.

42) Any other maintenance is welcome to be contacted manufacturer or our distributor.

2. MACHINE INFORMATION

2-1 SPECIFICATIONS

ITEM MODEL

Sliding table dimension 898x896mm

Extension table (rear) 952X896mm

Table size 896x1850 mm

Round rail ė0

Main saw blade (Max.) 305mm

Main saw bore 20mm

Max. cutting height with blade at 90 90mm

Max. cutting height with blade at 5 6 mm

Main motor power (1ph) 5HP(3.75 Kw)

Main blade speed 000rpm

Scoring blade motor 3/ HP (0.56KW)

Scoring blade speed 8000RPM

Cuting width 1300mm

Cuting width adjustment Manual

Main saw blade tilting adjustment Manual (0~ 5)

Main saw height adjustment Manual

Scoring saw height adjustment Manual

Saw guard overhead guard as option

Crosscut fence Manual

Dust collection system 120mm/6 mm

N.W./G.W./MEAS. (Machine) 312/382KGS (1 50x1150x1090mm)

Ctn QTY: 16/32 sets

2. MACHINE INFORMATION

2-2 MAIN FEATURE

A. RIP FENCE

B. MAIN SWITCH

C. BLADE UP AND DOWN HAND WHEEL

D. BLADE TILTING HAND WHEEL

E. EXTENSION TABLE

F. STANDARD GUARD

G. MITER GAUGE

3. ASSEMBLY & SETUP

3-1 SETUP SAFETY

1. Read and understand the warnings posted on the machine and in this manual.

Failure to comply with all of these warnings may cause serious injury.

2. Make certain the machine is properly grounded.

3. Provide ade uate space and surrounding for work area with non-glare, overhead

lighting. Keep the floor around the machine clean and free of scrap material, oil

and grease.

4. This model is a heavy-duty machine that weight's approximately 410 kgs. Serious

personal injury may occur if safe moving methods are not followed. To be safe,

you will need assistance and power e uipment when moving the shipping crate

and removing the machine from the crate.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sierra de Laguna Tools

Laguna Tools

Laguna Tools HW110LS-30 Manual de usuario

Laguna Tools

Laguna Tools DAKE SE-810 Manual de operación y mantenimiento

Laguna Tools

Laguna Tools MBAND18BX2203 Manual de usuario

Laguna Tools

Laguna Tools DAKE SE-1018 Manual de operación y mantenimiento

Laguna Tools

Laguna Tools 18BX Manual de usuario

Laguna Tools

Laguna Tools 16HD Classic Manual de usuario

Laguna Tools

Laguna Tools DAKE Euromatic 370S Manual de operación y mantenimiento

Laguna Tools

Laguna Tools MCO8000-0250 Manual de usuario

Laguna Tools

Laguna Tools DAKE SUPER CUT 315 Manual de usuario

Laguna Tools

Laguna Tools Timbermaster Manual de usuario

Laguna Tools

Laguna Tools DAKE JH10W1 Manual de operación y mantenimiento

Laguna Tools

Laguna Tools Fusion F1 Manual de usuario

Laguna Tools

Laguna Tools Dake VDL-18 Guía del usuario

Laguna Tools

Laguna Tools Fusion 1 Manual de usuario

Laguna Tools

Laguna Tools Dake Technics 350 CE Manual de usuario

Laguna Tools

Laguna Tools Dake VDL-18 Manual de operación y mantenimiento

Laguna Tools

Laguna Tools Fusion F1 Manual de usuario

Laguna Tools

Laguna Tools Fusion 2 Manual de usuario

Laguna Tools

Laguna Tools DAKE 14-10 Manual de usuario

Laguna Tools

Laguna Tools 14BX Series Manual de usuario

Laguna Tools

Laguna Tools LT14 SEL Manual de usuario

Laguna Tools

Laguna Tools 18CX Manual de usuario

Laguna Tools

Laguna Tools Fusion 3 Manual de usuario

Laguna Tools

Laguna Tools MPSP12-5-0135 Manual de usuario

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario