Laguna Tools Dake SB-32V Manual de operación y mantenimiento

Dake Corporation Phone: 800.937.3253 www.dakecorp.com

1809 Industrial Park Dr Fax: 800.846.3253

Grand Haven, MI 49417

DAKE DRILL PRESS

Model SB-32V

INSTRUCTIONAL MANUAL

WARNING!

Read and understand all instructions and responsibilities before operating. Failure to follow

safety instructions and labels could result in serious injury.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

977400-1V 1 REV012021

TABLE OF CONTENTS

DAKE STANDARD LIMITED WARRANTY ............................................................ 2

RETURN & REFUND POLICY ............................................................................... 4

SPECIFICATIONS.................................................................................................. 5

SAFETY.................................................................................................................. 6

SET UP................................................................................................................... 9

UNCRATING AND INSTALLATION .............................................................. 9

GROUNDING INSTRUCTIONS .................................................................... 9

CONTROLS.......................................................................................................... 10

OPERATION ........................................................................................................ 11

TAPPING OPERATIONS USING REVERSE FEATURE............................ 11

DRILL/CHUCK INSTALLATION .................................................................. 11

INSTALLATION OF DRILL BIT ................................................................... 12

TOOLING REMOVAL.................................................................................. 12

TABLE HEIGHT ADJUSTMENT ................................................................. 12

TABLE TILTING ADJUSTMENT ....................Error! Bookmark not defined.

TABLE SWING ADJUSTMENT................................................................... 13

FEED DEPTH ADJUSTMENT .................................................................... 13

WORK HOLDING........................................................................................ 14

SPEED ADJUSTMENT ............................................................................... 14

MAINTENANCE ................................................................................................... 16

TROUBLESHOOTING ......................................................................................... 17

ELECTRICAL DIAGRAM...................................................................................... 18

EXPLODED VIEWS & PART LISTS..................................................................... 19

ORDERING INFORMATION ................................................................................ 22

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

977400-1V 2 REV012021

DAKE STANDARD LIMITED WARRANTY

Finished Machines

Dake warrants to the original purchaser the finished machine manufactured or distributed by it to be free

from defects in material and workmanship under normal use and service within 1 year (12 months) from

the delivery date to the end user.

Parts

Dake warrants to the original purchaser the component part manufactured or distributed by it to be free

from defects in material and workmanship under normal use and service within 30 days from the delivery

date to the end user.

The standard limited warranty includes the replacement of the defective component part at no cost to the

end user.

Sale of Service (Repairs)

Dake warrants to the original purchaser the component part repaired by Dake Corporation at the

manufacturing facility to be free from defects in material and workmanship under normal use and service

within 90 days from the return date to the end user, as it pertains to the repair work completed. The

standard limited warranty includes repair of the defective component part, at no cost to the end user.

Warranty Process

Subject to the conditions hereinafter set forth, the manufacturer will repair or replace any portion of the

product that proves defective in materials or workmanship. The manufacturer retains the sole right and

option, after inspection, to determine whether to repair or replace defective equipment, parts or

components. The manufacturer will assume ownership of any defective parts replaced under this

warranty.

All requested warranty claims must be communicated to the distributor or representative responsible for

the sale. Once communication has been initiated, Dake Customer Service must be contacted for

approval:

Phone: (800) 937-3253

Email: [email protected]

When contacting Dake, please have the following information readily available:

- Model #

- Serial #

- Sales Order #

Purchasers who notify Dake within the warranty period will be issued a Case number and/or a Return

Material Authorization (RMA) number. If the item is to be returned per Dake’s request, the RMA number

must be clearly written on the exterior packaging. Any item shipped to Dake without an RMA will not be

processed.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

977400-1V 3 REV012021

Warranty Exceptions:

The following conditions are not applicable to the standard limited warranty:

(a) Part installation or machine service was not completed by a certified professional, and is not

in accordance with applicable local codes, ordinances and good trade practices.

(b) Defects or malfunctions resulting from improper installation or failure to operate or maintain

the unit in accordance with the printed instructions provided.

freight terms.

(d) Normal maintenance service or preventative maintenance, and the parts used in connection

with such service.

(e) Units and parts which have been altered or repaired, other than by the manufacturer or as

specifically authorized by the manufacturer.

(f) Alterations made to the machine that were not previously approved by the manufacturer, or

that are used for purposes other than the original design of the machine.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

977400-1V 4 REV012021

RETURN & REFUND POLICY

Thank you for purchasing from Dake! If you are not entirely satisfied with your purchase, we are

here to help.

Returns

All Dake manufactured / distributed machines, parts and couplings include a 30-day return

option. These policies are valid from the date of final shipment to the end user.

To be eligible for a return, the item must be unused and in the same condition as received.

All requested warranty claims must be communicated to the distributor or representative

responsible for the sale. Once communication has been initiated, Dake Customer Service must

be contacted for approval:

Phone: (800) 937-3253

Email: customerser[email protected]

Once the return request has been approved by Customer Service, a representative will supply a

Return Material Authorization (RMA) number. The returned item must have the provided RMA

number clearly marked on the outside packaging. Any item received without an RMA number

clearly visible on the packaging will not be processed.

An RMA number can only be provided by the Dake Customer Service team and must be

obtained prior to the return shipment.

Refunds

Once the item has been received and inspected for damages, a representative will notify the

requestor referencing the provided RMA number.

If the return is approved, a refund will be issued to the original method of payment, less a 20%

restocking fee. The restocking fee may be waived if an order is placed at the time of return with

like-value merchandise.

Transportation costs are the responsibility of the end user and will not be credited upon return

approval.

Any item that is returned after the initial 30 days or has excessive/obvious use will not be

considered for a full refund.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

977400-1V 5 REV012021

SPECIFICATIONS

Model

SB-32V

Number

977400-1V

Voltage

110V Single Phase

Horsepower

2 HP

Drill Type

Floor

Max. Drill Capacity

1-1/4”

Spindle Taper

MT4

Spindle Travel

5-1/4”

Max. Work Diameter

18”

Speeds

Variable Speed

Spindle Speed Range

46 - 3,473 RPM

Column Diameter

4”

Table

15-3/4” x 15-3/4”

Base

23-5/8” x 15”

Spindle to Table

26-1/4”

Spindle to Base

50”

Overall Height

71”

Weight

483 lbs.

In the space provided record the serial number and model number of the machine. If contacting

Dake this information must be provided to assist in identifying the specific machine.

Serial No.

Model No.

Date Purchased:

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

977400-1V 6 REV012021

SAFETY

This is the safety alert symbol. When you see this symbol on your machine be alert to

the potential for personal injury.

Carefully read all safety messages in these instructions and on your machine safety

signs. Keep safety labels in good condition. Replace missing or damaged labels.

Employer is responsible to perform a hazard/PPE assessment before work activity.

Additional Safety Warnings:

•Keep guards in place and in working order.

•Remove adjusting key and wrenches, be in the habit of checking to see that keys and

adjusting wrenched are removed from tool before turning on.

•Keep work area clean. Cluttered areas and benches invite accidents.

•Do not use in dangerous environments. Do not use in damp or wet locations or expose

them to rain.

•Do not force tool. Machine will do a better and safer job at the rate for which it was

designed.

Label Part No.

84395

Label Part No.

76462

Label Part No.

82199

Label Part No.

300168

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

977400-1V 7 REV012021

•Use the right tool. Do not force the tool or use the machine to do a job for which it was

not designed.

•Do not wear gloves, neckties, necklaces, rings, or loose clothing. Non-slip footwear is

recommended. Wear protective hair covering to contain long hair.

•Always use safety glasses. Also use face or dust mask if cutting operation is dusty.

•Secure work. Use clamps or vise to hold work. Do not hold parts with hands.

•Do not overreach. Keep proper footing and balance at all times.

•Maintain tools with care. Keep tools sharp and clean for best and safest performance.

•Disconnect drill press from power before servicing or changing accessories such as bits,

cutters, etc.

•Never stand on machine for risk of serious injury.

•Never leave tool running unattended. Turn power off. Do not leave machine until it comes

to a complete stop.

•Be sure drill bit or cutting tool is securely in the chuck.

•Never place your fingers in a position where they could contact the drill or cutting tool of

the work piece should unexpectedly shift.

•Never perform any operation by moving the head or table with respect to one another.

•Do not switch machine on or start any operation before checking that the head and table

lock handles are clamped tight to column, and the head and table support collars are

correctly positioned.

•Operation of the drill press incorrectly, or on a dangerous fashion can result in serious

injury or death, damage to the machine, it’s components, or cutting tool.

•The drill press is designed for drilling and boring operations. Cautions is required when

operating the drill press because it can be dangerous due to the high spindle rotation

speed.

•Guards such as pully cover and chuck guard must be in place and in working condition to

prevent hazard.

•Switch the power off before setting, inspecting, lubricating, cleaning, or changing the drill

bit.

•To clamp work piece to brace against column to prevent material rotation.

•Using recommended speed for drill bit, and work piece material.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

977400-1V 8 REV012021

•All visitors should be kept a safe distance from work area.

•Make workshop kid proof with padlocks, master switches, or by removing the starter key.

•Reduce the risk of accidental starting. Make sure switch is in off position before plugging

in.

•Use recommended accessories. The use of improper accessories may cause risk of

injury.

•Adjust the table or depth stop to avoiding drilling into the table, shut off the power.

Remove the drill bit or cutting tool, and clean the table before leaving the machine.

•Do not operate until completely assembled and installed according to the instructions.

•If any part of your drill press is malfunctioning, has been damaged, or broken do not

operate until the part is properly repaired or replaced.

•Lockout the motor switch when leaving the drill press. Don’t perform layout, assembly, or

setup work on the table while the cutting tools rotating.

Voltage Warning:

•Before connecting the machine to a power source know your incoming voltage.

•At power source with voltage greater than that specified for the machine can result in

serious injury to the user and can damage the machine.

•Using a power source with voltage less than that of the machines rating can damage the

motor and other components.

•If you are unsure of the voltage rating do not use the machine.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

977400-1V 9 REV012021

SET UP

UNCRATING AND INSTALLATION

1. Location of the drill press should be in a well-lit area with correct power supply and that

will not interfere with other machines or operations.

2. Carefully uncrate machine and inspect all packing to make sure no parts are manuals

are thrown out.

3. When transporting the machine please use caution. If using a sling have someone

steady the machine while moving.

4. Install your drill press on a sturdy level floor surface. It must be anchored to the floor; the

machine is top heavy.

5. Connect appropriate power to the machine. Make sure circuit breakers are suitable for

the machine. Consult local codes for proper installation of machine. Always route power

cables in a safe manner away from traffic areas, damp areas, heat, and moving parts.

6. After installing the drill press, use degreasing product to clean off the anti-rust oil which

was applied at the factory. Then wipe machined surfaces with a light coating of lubricant

oil (way oil).

7. Check for damaged parts before further use of the machine. A guard or other part that is

damaged should be replaced or repaired before use. Carefully check to determine that it

will operate properly and perform its intended function. Check for alignment of moving

parts and binding od moving parts. Breakage of parts or mountings and or any other

conditions that could be affect its operation.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding provides a path of least resistance for

electric current to reduce the risk or electrical shock. This machine is equipped with an electric

cord must be used with a matching outlet that is properly installed and grounded in accordance

with all local codes and ordinances.

•Do not modify the plug provided. If it will not fit the outlet have the proper outlet installed

by a qualified electrician.

•Improper connection of the equipment grounding can result in a risk of electrical shock.

The conductor with insulation having an outer surface that is green with yellow stripes is

equipment grounding conductor. If repair or replacement of the electric cord or plug is

necessary, do not connect the equipment grounding conductor to a live terminal.

•Check with a qualified electrician or serviceman if the grounding instructions are not

completely understood, or if in doubt as whether the machine is properly grounded.

•It is not recommended to use an extension cord on the machine. If one must be used,

use only a grounded cord on the machine and length of run needed.

•Repaired or replace damaged or worn cords immediately.

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Laguna Tools

Laguna Tools

Laguna Tools MJO6405-0800 Manual de usuario

Laguna Tools

Laguna Tools P12 10 Manual de usuario

Laguna Tools

Laguna Tools PP16 XC Pro Manual de usuario

Laguna Tools

Laguna Tools DAKE 4 Manual de usuario

Laguna Tools

Laguna Tools DAKE 33-493 Manual de usuario

Laguna Tools

Laguna Tools MJOIN 8012-0130 Manual de usuario

Laguna Tools

Laguna Tools Dake 6-275 Manual de operación y mantenimiento

Laguna Tools

Laguna Tools DAKE 75H Manual de operación y mantenimiento

Laguna Tools

Laguna Tools DAKE 1-1/2C Manual de operación y mantenimiento

Laguna Tools

Laguna Tools MJOPL104200 Manual de usuario

Laguna Tools

Laguna Tools T800i Manual de usuario

Laguna Tools

Laguna Tools DAKE SB-25V Manual de operación y mantenimiento

Laguna Tools

Laguna Tools DAKE X Manual de usuario

Laguna Tools

Laguna Tools PP16 XC Pro Manual de usuario

Laguna Tools

Laguna Tools Platinum Series Manual de usuario

Laguna Tools

Laguna Tools DAKE Force 50DA Manual de operación y mantenimiento

Laguna Tools

Laguna Tools DAKE Force 25DA Manual de operación y mantenimiento

Laguna Tools

Laguna Tools DAKE 1-1/2 Manual de operación y mantenimiento

Laguna Tools

Laguna Tools DAKE 3 Manual de usuario

Laguna Tools

Laguna Tools RPM5 Manual de usuario

Laguna Tools

Laguna Tools DAKE Force 10DA Manual de operación y mantenimiento

Laguna Tools

Laguna Tools P12 5 Manual de usuario

Laguna Tools

Laguna Tools DAKE 5 Manual de usuario

Laguna Tools

Laguna Tools Dake Force 150 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual