Laguna Tools Dake 6-275 Manual de operación y mantenimiento

Dake Corporation Phone: 800.937.3253 www.dakecorp.com

1809 Industrial Park Dr Fax: 800.846.3253

Grand Haven, MI 49417

DAKE AIR-OPERATED HYDRAULIC PRESS

Model 6-275 & 6-475

INSTRUCTIONAL MANUAL

WARNING!

Read and understand all instructions and responsibilities before operating. Failure to follow

safety instructions and labels could result in serious injury.

*Model 6-250 shown. May be slight differences.

 Dake Corporation 
 1809 Industrial Park Dr 
 Grand Haven, MI 49417 
www.dakecorp.com 
 
 1 REV062022 
 
TABLE OF CONTENTS 
 
DAKE STANDARD LIMITED WARRANTY............................................................ 2
RETURN & REFUND POLICY..............................................................................4
SAFEGUARDING THE POINT OF OPERATION..................................................5
SPECIFICATIONS ................................................................................................6
SAFETY................................................................................................................7
SET UP.................................................................................................................8
OPERATION.........................................................................................................9
MAINTENANCE....................................................................................................9
LUBRICATION.............................................................................................9
TROUBLESHOOTING........................................................................................ 10
EXPLODED VIEW & PARTS LIST...................................................................... 12
ORDERING INFORMATION............................................................................... 21

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

2 REV062022

DAKE STANDARD LIMITED WARRANTY

Finished Machines

Dake warrants to the original purchaser the finished machine manufactured or distributed by it to be free

from defects in material and workmanship under normal use and service within 1 year (12 months) from

the delivery date to the end user.

Parts

Dake warrants to the original purchaser the component part manufactured or distributed by it to be free

from defects in material and workmanship under normal use and service within 30 days from the delivery

date to the end user.

The standard limited warranty includes the replacement of the defective component part at no cost to the

end user.

Sale of Service (Repairs)

Dake warrants to the original purchaser the component part repaired by Dake Corporation at the

manufacturing facility to be free from defects in material and workmanship under normal use and service

within 90 days from the return date to the end user, as it pertains to the repair work completed. The

standard limited warranty includes repair of the defective component part, at no cost to the end user.

Warranty Process

Subject to the conditions hereinafter set forth, the manufacturer will repair or replace any portion of the

product that proves defective in materials or workmanship. The manufacturer retains the sole right and

option, after inspection, to determine whether to repair or replace defective equipment, parts or

components. The manufacturer will assume ownership of any defective parts replaced under this

warranty.

All requested warranty claims must be communicated to the distributor or representative responsible for

the sale. Once communication has been initiated, Dake Customer Service must be contacted for

approval:

Phone: (800) 937-3253

Email: customerservice@dakecorp.com

When contacting Dake, please have the following information readily available:

- Model #

- Serial #

- Sales Order #

Purchasers who notify Dake within the warranty period will be issued a Case number and/or a Return

Material Authorization (RMA) number. If the item is to be returned per Dake’s request, the RMA number

must be clearly written on the exterior packaging. Any item shipped to Dake without an RMA will not be

processed.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

3 REV062022

Warranty Exceptions:

The following conditions are not applicable to the standard limited warranty:

(a) Part installation or machine service was not completed by a certified professional, and is not

in accordance with applicable local codes, ordinances and good trade practices.

(b) Defects or malfunctions resulting from improper installation or failure to operate or maintain

the unit in accordance with the printed instructions provided.

freight terms.

(d) Normal maintenance service or preventative maintenance, and the parts used in connection

with such service.

(e) Units and parts which have been altered or repaired, other than by the manufacturer or as

specifically authorized by the manufacturer.

(f) Alterations made to the machine that were not previously approved by the manufacturer, or

that are used for purposes other than the original design of the machine.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

4 REV062022

RETURN & REFUND POLICY

Thank you for purchasing from Dake! If you are not entirely satisfied with your purchase, we are

here to help.

Returns

All Dake manufactured / distributed machines, parts and couplings include a 30-day return

option. These policies are valid from the date of final shipment to the end user.

To be eligible for a return, the item must be unused and in the same condition as received.

All requested warranty claims must be communicated to the distributor or representative

responsible for the sale. Once communication has been initiated, Dake Customer Service must

be contacted for approval:

Phone: (800) 937-3253

Email: [email protected]

Once the return request has been approved by Customer Service, a representative will supply a

Return Material Authorization (RMA) number. The returned item must have the provided RMA

number clearly marked on the outside packaging. Any item received without an RMA number

clearly visible on the packaging will not be processed.

An RMA number can only be provided by the Dake Customer Service team and must be

obtained prior to the return shipment.

Refunds

Once the item has been received and inspected for damages, a representative will notify the

requestor referencing the provided RMA number.

If the return is approved, a refund will be issued to the original method of payment, less a 20%

restocking fee. The restocking fee may be waived if an order is placed at the time of return with

like-value merchandise.

Transportation costs are the responsibility of the end user and will not be credited upon return

approval.

Any item that is returned after the initial 30 days or has excessive/obvious use will not be

considered for a full refund.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

5 REV062022

SAFEGUARDING THE POINT OF OPERATION

ANSI B11.2 - Hydraulic Power Presses -

Safety Requirements for Construction, Care, and Use

It is important that Dake press users have a clear understanding of their responsibility involving the care

and use of their Dake hydraulic press, including point-of-operation safe guards. Dake strongly

recommends that Dake press users obtain a copy of the current American National Standard Institute

(ANSI) B11.2 standard, for a more complete understanding of their responsibilities.

ANSI B11.2 states the following, relative to point of operation safeguarding:

“Normally, only the employer (press user) can determine the requirements of the press productions

system components, including the dies and methods for feeding. Therefore, the employer is ultimately

responsible to designate and provide the point-of-operation safeguarding system.”

The standard also discusses additional responsibilities of the employer. Some of the key responsibilities

are:

•The employer is responsible for the safety, use, and care of the hydraulic power press production

system.

•The employer is responsible to consider the sources of hazards for all tasks to be implemented on

the hydraulic power press production system.

•The employer is required to eliminate, or control identified hazards in the scope of their work activity.

•The employer is responsible for the training of personnel, caring for, inspecting, maintaining, and

operating hydraulic press production systems to ensure their competence.

•The employer is responsible to provide and ensure that point-of-operation safeguarding is used,

checked, maintained, and where applicable, adjusted on every production operation performed on a

press production system.

A complete and current copy of the ANSI B.11.2 standard can be obtained by contacting the following:

American National Standards Institute

1430 Broadway

New York, NY 10018

AMT –The Association for Manufacturing Technology

7901 Westpark Drive

McLean, VA 22102

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

6 REV062022

SPECIFICATIONS

Model 6-275

Model 6-475

Number

906275

906475

Capacity

75 tons

Width between uprights

44”

Width between table channels

8-1/4”

8/1/4”

Minimum ram to table

6”

Maximum ram to table

36”

Ram travel

10”

Horizontal work head travel

24-5/8”

Height

86”

Weight

1,500 lbs

1,550 lbs

Base

55” x 36”

55” x36”

Ram advance speed

45 ipm

40 ipm

Pressing speed

2 ipm

3-1/2 ipm

Number or pumps

Air pressure

90-125 psi

In the space provided record the serial number and model number of the machine. This

information is only found on the black and gold Dake tag shown below. If contacting Dake this

information must be provided to assist in identifying the specific machine.

Serial No.

Model No.

Install Date:

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

7 REV062022

SAFETY

This is the safety alert symbol. When you see this symbol on your press be alert to the

potential for personal injury.

Employer is responsible to perform a hazard/PPE assessment before work activity.

Follow recommended precautions and safe operating practices.

Additional Warnings:

•Carefully read all safety messages in these instructions and on your press safety signs.

•Keep safety labels in good condition. Replace missing or damaged safety labels.

•Do not alter this press from its original state.

•Only use Dake original parts.

•This machine is intended to be operated by one person. This person should be conscious

of the press ram movement not only for themselves but also for other persons in the

immediate area.

•Tag out procedures must be followed by authorized employees as per OSHA.

Label Part No. 300168

Label Part No.

84399

Label Part No.

84395

Label Part No.

84487

Label Part No.

76462

Label Part No.

607

Label Placement View

Label Part No.

7355

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

8 REV062022

SET UP

For shipping convenience some of the parts are not assembled. Assemble these parts in the

following order:

1. Bolt the base angles to uprights using four provided bolts and nuts. Ensure that the base

angles are against the stops on the uprights. The press should set on a level floor with

base angles touching the floor at all points, use shims when necessary.

2. Connect airline in to street elbow (Item 136) at the right side of the control block. Avoid

restrictions in air supply line to ensure ampler air to the air motor. For maximum

performance the air supply line should be 1/2” pipe if the distance from the compressor to

the press is 0-30 feet, 3/4” line for 30-60 feet, and 1” if distance is greater then 60 feet.

WARNING: AIR MUST BE MOISTURE FREE. WATER IN THE AIR LINE COULD

CORRODE PRESS BEYOND REPAIR.

3. Oil Requirements: Fill the reservoir with Mobil DTE 24 or equivalent oil through the

pipeline in back of the press at pipe coupling by removing the pipe plug. Make sure the

air source is removed from the reservoir prior to removing the plug. Oil level may

be checked, with the ram up, by removing the pipe plug on the right side of the

reservoir near the front. Replace plug before operating the press.

Model 6-275 & 6-475, 75-ton presses use 10 quarts.

4. Attach nose piece to ram by inserting shank into ram and tightening the set screw.

5. Place the hoist crank on the lift drum shaft. Turn the hoist crank to relieve the pressure on

the table pins. Keeping tension on the hoist crank, remove the table pins one at a time.

a. After removing the table pins turn the crank running the table channels from top to

bottom. Check to make sure the cable is tracking correctly. The cable should be

on each of the two upper pulleys and should track back and forth on the cable

drum. Always place table pins under the table channels before releasing the hoist

crank when positioning the table channels for cable tracking, servicing, or set-up

for desired work opening.

b. If a tracking problem exists contact Dake for instructions. Be sure all table pins are

fully inserted in place before applying pressure. Always remove or release

pressure on the cable before pressure is applied.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

9 REV062022

OPERATION

WARNING DO NOT OVERSTROKE THE RAM. Over-stroking will cause premature seal

failure. Models 6-275, and 6-475 have a 10-inch stroke.

The press has been completely tested at the factory and after setting up according to this

manual the press is ready for operation. However it is necessary for the operator to acquaint

themselves with the controls.

1. Three screws (Item 109) are used to lock the workhead in desired position along the

head channels.

2. The handcrank is to raise and lower the work table channels to proper work height. When

desired height is obtained insert the table pins. Models 6-275, and 6-475 use 2 pins on

each side, 4 total. Be sure all table pins are in place and in as far as they can go

before pressure is applied. Be sure to slack off the cable before pressure is

applied. See step 5 of the “SET UP” in this manual.

3. The handle on the left side of the control block (Item 76) opens and closes the ball valve

which releases the ram pressure. This valve should be kept firmly closed and opened

only when it is desired to return the ram to its up position.

4. The two table plates and two V-blocks are used for supporting the work in process.

5. The control knob (Item 103) on the right side of the panel regulates the speed of ram

travel. The knob will return to the off position when released.

6. The relief valve (Item 90) had been set at factory to open at maximum tonnage of the

press. The valve can be adjusted by removing the hex nut located on the top of the valve

block at the right front of the reservoir and turning the adjusting screw to the left for a

lower setting. WARNING: NEVER EXCEED THE RATED TONNAGE OF THE

PRESS.

MAINTENANCE

Recommended to replace hydraulic oil every 6 months of machine use. See step 3 in “SET UP”

section for instructions.

LUBRICATION

•Keep all working parts of the press well-oiled for easier operation.

•Keep a light film of oil over the entire surface of the ram to prevent rust.

•Regularly clean off work surfaces and the surrounding work area.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Laguna Tools

Laguna Tools

Laguna Tools MRS5000-0280 Manual de usuario

Laguna Tools

Laguna Tools Platinum Series Manual de usuario

Laguna Tools

Laguna Tools P12 10 Manual de usuario

Laguna Tools

Laguna Tools DAKE SB-25V Manual de operación y mantenimiento

Laguna Tools

Laguna Tools DAKE X Manual de usuario

Laguna Tools

Laguna Tools Dake Force 150 Manual de usuario

Laguna Tools

Laguna Tools DAKE 1-1/2 Manual de operación y mantenimiento

Laguna Tools

Laguna Tools MJOIN 8012-0130 Manual de usuario

Laguna Tools

Laguna Tools PP16 XC Pro Manual de usuario

Laguna Tools

Laguna Tools DAKE Force 50DA Manual de operación y mantenimiento

Laguna Tools

Laguna Tools RPM5 Manual de usuario

Laguna Tools

Laguna Tools PP16 XC Pro Manual de usuario

Laguna Tools

Laguna Tools DAKE 33-672 Manual de usuario

Laguna Tools

Laguna Tools DAKE 1 Manual de usuario

Laguna Tools

Laguna Tools DAKE 33-493 Manual de usuario

Laguna Tools

Laguna Tools DAKE 1-1/2C Manual de operación y mantenimiento

Laguna Tools

Laguna Tools DAKE 75H Manual de operación y mantenimiento

Laguna Tools

Laguna Tools DAKE Y Manual de usuario

Laguna Tools

Laguna Tools T800i Manual de usuario

Laguna Tools

Laguna Tools MJO6405-0800 Manual de usuario

Laguna Tools

Laguna Tools PRO SERIES Manual de usuario

Laguna Tools

Laguna Tools Platinum Series Manual de usuario

Laguna Tools

Laguna Tools DAKE 4 Manual de usuario

Laguna Tools

Laguna Tools P12 5 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual