Labelmate UCAT-S Manual de usuario

MAINTENANCE:

Your UCAT-S requires no maintenance.

Product Limited Warranty

All Labelmate Products are warranted to the original end-user customer to be free from defects in

materials and workmanship. If it is determined by Labelmate that a product has failed under the terms of

this warranty, the product will be repaired or replaced at no charge to the customer. Labelmate reserves all

rights to determination of coverage and liability under this warranty. The warranty period for all new

Labelmate products is outlined below:

The warranty period for all products starts on the date purchased by the original end-user customer.

Warranty coverage is not transferable with ownership and will terminate immediately upon rental, resale or

any other change in ownership. This warranty does not cover repair to any product which is damaged, has

been modified, is missing parts, or has been opened or repaired by any unauthorised person. Use of any

unauthorised accessory or attachment will void coverage. Purchase documentation should be retained for

coverage verification.

In the event your product requires service, please contact the distributor you bought the product from. The

customer assumes responsibility for all cost and risk incurred in transport for service.

Labelmate makes no other warranty of any kind expressed or implied, or to suitability or fitness for a

particular purpose. No other person, agent or reseller is authorised to give any warranties on behalf of

Labelmate. Any obligation to warranty other than that specifically addressed above is hereby disclaimed.

Warranty Period

Products Covered

5 years

Label Rewinders

Label Unwinders

3 years

Label Counters (mechanical parts

only)

Label Slitters (mechanical parts

only)

Label Dispensers

Printer Mechanisms

1 year

Power Supply Modules

Counter modules

Encoders

Any products not specified above.

SPRL

290, Chaussée de Ruisbroek, 1620 Drogenbos, BELGIUM

TEL: +32 2.375.69.60 –FAX: +32 2.375.38.96

brussels@labelmate.com

www.labelmateeurope.com

Economy Label Unwinder

with Adjustable "Wearless" Braking

•Low-cost economy Unwinder

•Adjustable Braking

•Non-Powered

Remove all parts from the shipping container and verify contents.

PACKAGE CONTENTS:

•User Manual (this document)

•UCAT-S Unit

•Plastic bag with three (3) vanes and 6 screws

•One 300mm Plastic Inner Flange Plate

Retain the Shipping Container and Packaging for Storage and Transport

SPECIFICATIONS:

Weight of the machine: 6Kg.

Max. Label Roll Weight: 6Kg.

Max. Label Roll Diam: 300mm.

IMPORTANT INFORMATION:

•This product is a label unwinder. It is only to be used to unwind labels of the

recommended dimensions and weight in an indoor, dry environment.

•The machine is to be used on a flat surface, if the surface is not flat; it is to

be fixed using the holes in the base plate.

•The ambient light of the working area needs to be sufficient to avoid any risk.

•The unwinder can be used in ambient temperatures of +2°C to 40°C.

SET-UP:

1. Slide the Flange Plate onto the brass shaft

2. Install the three (3) metal vanes onto the shaft. The side with the 3 holes for

the screws has to be facing the rotation direction.

3. Position the Plastic Flange Plate even with the inside end of the Shaft so

there is clearance between the Flange and the Chassis.

4. Tighten the screw in the Hub until it is snug.

5. CAUTION: AVOID ACCIDENTS. THE UCAT-S WEIGHS OVER 6KG, SO

CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT.

Your UCAT-S is now ready for use.

LABEL UNWINDING:

The UCAT-S is bi-directional. It can unwind labels in either direction.

1. Slide the roll of labels to be unwound / slit onto the shaft of the UCAT-S and

all the way up against the Plastic Flange Plate.

2. Thread the labels into the printer / slitter as required

3. Begin the printing operation and observe that the labels are feeding correctly

into your printer / slitter. If necessary, adjust the position of the UCAT-S so

the alignment with the printer / slitter is appropriate to correctly feed the

labels.

4. Braking is adjusted by turning the red knob.

LOADING HEAVY ROLLS:

In order to ease the loading of heavy rolls on the UCAT-S, the unit can be placed

on its back. Slide the roll on the shaft and then reposition the unit straight.

OPTIONAL:

The tension is adjustable via the red knob. This knob can be replaced with a

regular M5 screw so the adjustment can only be made with a wrench, in order to

prevent the operator to change the brake setting.

WARNING!

This Product is for indoor use only.

Not for use in wet locations.

Otros manuales para UCAT-S

Otros manuales de Etiquetadora de Labelmate

Labelmate

Labelmate ZCAT-3 Hoja de información del producto

Labelmate

Labelmate MC-11 Manual de usuario

Labelmate

Labelmate PM-300-CS Manual de usuario

Labelmate

Labelmate RRC-330 Manual de usuario

Labelmate

Labelmate UNI-CAT STANDARD Manual de usuario

Labelmate

Labelmate CAT-3 Manual de usuario

Labelmate

Labelmate UCAT-S Manual de usuario

Labelmate

Labelmate TWIN-MATRIX-6-R/L Manual de instrucciones

Labelmate

Labelmate S-100 Manual de usuario

Labelmate

Labelmate PM-300-CS Manual de usuario

Labelmate

Labelmate DISTRI-ST Manual de usuario

Labelmate

Labelmate BOXMATE-610 Manual de usuario

Labelmate

Labelmate LD-100S Manual de usuario

Labelmate

Labelmate UCAT-40 Manual de usuario

Labelmate

Labelmate MC-11 Manual de usuario

Labelmate

Labelmate LD-300-UNI Manual de usuario

Labelmate

Labelmate BOTTLEMATE-910P Manual de usuario

Labelmate

Labelmate UCAT-1 Manual de usuario

Labelmate

Labelmate UCAT-1 Manual de usuario

Labelmate

Labelmate SR6 Manual de usuario

Manuales populares de Etiquetadora de otras marcas

Brother

Brother P-Touch 2420PC Manual de usuario

newell

newell Dymo LabelManager 210D Manual de usuario

Brother

Brother TD-4000 Manual de usuario

U-Line

U-Line BROTHER H-8754 Manual de usuario

Tharo Systems

Tharo Systems H-435+ Manual de usuario

Brother

Brother E300 Manual de usuario

Godex

Godex RT700 SERIES Manual de usuario

ID Technology

ID Technology 252 Manual de usuario

CAB

CAB XD4M/300 Manual de usuario

Avery Dennison

Avery Dennison Pathfinder 6057 Manual de servicio

Brother

Brother P-touch PT-9700PC Manual de usuario

TSC

TSC PEX1000 Series Manual de usuario

Adkins

Adkins Label Master Manual de usuario

Epson

Epson LabelWorks LW-400 Manual de usuario

Primera

Primera 510212 Manual de usuario

Brady

Brady BradyPrinter S3100 Manual de usuario

DuraLabel

DuraLabel LabPRO Manual de usuario

Novexx Solutions

Novexx Solutions XLP 604 Manual de usuario