Labconco Protector Premier 10040 Series Manual de usuario

Original instructions

ProtectorPremier

Laboratory Fume Hoods

Models

10040 Series

10050 Series

10060 Series

10080 Series

Original instructions

the right to make periodic design changes without obligation to notify any person or entity of such change.

Returned or Damaged Goods

Do not return goods without the prior authorization from Labconco. Unauthorized returns will not be

accepted. If your shipment was damaged in transit, you must file a claim directly with the freight carrier.

Labconco Corporation and its dealers are not responsible for shipping damages.

The United States Interstate Commerce Commission rules require that claims be filed with the delivery

carrier within fifteen (15) days of delivery.

Limitation of Liability

The disposal and/or emission of substances used in connection with this equipment may be governed by

various federal, state, or local regulations. All users of this equipment are required to become familiar with

any regulations that apply in the user’s area concerning the dumping of waste materials in or upon water,

land, or air and to comply with such regulations. Labconco Corporation is held harmless with respect to

user’s compliance with such regulations.

Contacting Labconco Corporation

If you have questions that are not addressed in this manual, or if you need technical assistance, contact

Labconco’s Customer Service Department or Labconco’s Product Service Department at 1-800-821-5525

or 1-816-333-8811, between the hours of 7:30 a.m. and 5:30 p.m., Central Standard Time.

Part #9410500, Rev. L

ECO N065

Warranty

Labconco Corporation provides a warranty to the original buyer for the repair or replacement of parts and

reasonable labor as a result of normal and proper use of the equipment with compatible chemicals. Broken

glassware and maintenance items, such as filters, gaskets, light bulbs, finishes and lubrication are not

warranted. Excluded from warranty are products with improper installation, erratic electrical or utility supply,

unauthorized repair and products used with incompatible chemicals.

The warranty for Protector®Premier®Laboratory Fume Hoods will expire one year from date of installation or

two years from date of shipment from Labconco, whichever is sooner. Warranty is non-transferable and only

applies to the owner (organization) of record.

Buyer is exclusively responsible for the set-up, installation, verification, decontamination or calibration of

equipment. This limited warranty covers parts and labor, but not transportation and insurance charges. If the

failure is determined to be covered under this warranty, the dealer or Labconco Corporation will authorize

repair or replacement of all defective parts to restore the unit to operation. Repairs may be completed by 3rd

party service agents approved by Labconco Corporation. Labconco Corporation reserves the rights to limit this

warranty based on a service agent’s travel, working hours, the site’s entry restrictions and unobstructed access

to serviceable components of the product.

Under no circumstances shall Labconco Corporation be liable for indirect, consequential, or special damages

of any kind. This warranty is exclusive and in lieu of all other warranties whether oral, or implied.

Original instructions

TABLE OF CONTENTS

CHAPTER 1: INTRODUCTION 1

About This Manual 2

Typographical Conventions 3

(Conventions Typographiques)

Your Next Step 4

CHAPTER 2: PREREQUISITES 5

Location Requirements 6

Support Requirements 6

Exhaust Requirements 6

Electrical Requirements 7

(Exigences électriques)

Service Line Requirements 8

Space Requirements 8

CHAPTER 3: GETTING STARTED 9

Unpacking Your Fume Hood 10

Removing the Shipping Skid 10

Sash Weight Release 11

Installing the Hood on a Supporting Structure & Work Surface 11

Connecting to the Hood Exhaust System 13

Connecting the Electrical Supply Source 13

Connecting the Service Lines to the Protector Hood 16

Sealing the Protector Hood to the Work Surface 17

Certifying the Protector Fume Hood 17

CHAPTER 4: PERFORMANCE FEATURES AND SAFETY

PRECAUTIONS 18

Performance Features 18

Safety Precautions 21

(Consignes de sécurité)

CHAPTER 5: USING YOUR PROTECTOR PREMIER 25

Operating the Vertical Rising Sash 25

Operating the A-Style Combination Sash 25

Operating the Blower 25

Operating the Lights 26

Working in your Protector Fume Hood 26

CHAPTER 6: MAINTAINING YOUR PROTECTOR PREMIER 28

Service Safety Precautions 28

(Mesures de sécurité des services)

Routine Maintenance Schedule 29

Routine Service Operations 30

CHAPTER 7: MODIFYING YOUR PROTECTOR PREMIER 31

Installing Work Surfaces 31

Installing Ceiling Enclosures Above the Fume Hood 32

Installing Rear Panels Behind the Fume Hood 34

Installing Additional Service Fixtures 35

Installing Guardian Airflow Monitors 35

Distillation Grids –Field Installation 35

Sash Stop Kit –Field Installation 36

Upper Bypass –Field Installation 36

Installing an Electrical Duplex Outlet 36

(Installation d'une sortie Duplex électrique)

8' Dual Exhaust Adapter 36

CHAPTER 8: TROUBLESHOOTING 37

APPENDIX A: PROTECTOR PREMIER COMPONENTS 40

APPENDIX B: PROTECTOR PREMIER DIMENSIONS 43

APPENDIX C: PROTECTOR PREMIER SPECIFICATIONS 45

(ANNEXE C: SPÉCIFICATIONS PROTECTEUR DU PREMIER MINISTRE)

APPENDIX D: PROTECTOR I-S HOOD 48

APPENDIX E: SERIAL NUMBER TAG DESCRIPTION 56

(ANNEXE D: DESCRIPTION DE SÉRIE TAG NUMBER)

APPENDIX F: REFERENCES 62

APPENDIX G: VAV OPEN AREA GUIDELINES 65

Product Service 1-800-522-7658

Original instructions

CHAPTER 1

INTRODUCTION

Congratulations on your purchase of a Labconco Protector® Premier® Laboratory

Fume Hood. Your Protector Laboratory Fume Hood is designed to protect you. It

is the result of Labconco’s more than 60 years of experience in manufacturing

fume hoods, and users like you suggested many of its features to us.

The Labconco Protector Premier Fume Hood has been engineered to provide

maximum visibility in a laboratory, and effectively contain toxic, noxious, or

other harmful materials when properly installed. The Protector Premier offers

many unique features to enhance safety, performance, and visibility. To take full

advantage of them, please acquaint yourself with this manual and keep it handy

for future reference. If you are unfamiliar with how fume hoods operate, please

review Chapter 4: Performance Features and Safety Precautions before you

begin working in the fume hood. Even if you are an experienced fume hood user,

please review Chapter 5: Using Your Protector Premier, which describes your

Protector Hood’s features so that you can use the hood efficiently.

Figure 1-1

Chapter 1: Introduction

Product Service 1-800-522-7658

Original instructions

About This Manual

This manual is designed to help you learn how to install, use, and maintain your

laboratory fume hood. Instructions for installing optional equipment on your

hood are also included.

Chapter 1: Introduction provides a brief overview of the laboratory fume hood,

explains the organization of the manual, and defines the typographical

conventions used in the manual.

Chapter 2: Prerequisites explains what you need to do to prepare your site before

you install your laboratory fume hood. Electrical and service requirements are

discussed.

Chapter 3: Getting Started contains the information you need to properly unpack,

inspect, install, and certify your laboratory fume hood.

Chapter 4: Performance Features and Safety Precautions explains how the

Protector operates and the appropriate precautions you should take when using the

fume hood.

Chapter 5: Using Your Protector Premier discusses the basic operation of your

fume hood. Information on how to prepare, use and shut down your Protector

Hood are included.

Chapter 6: Maintaining Your Protector Premier explains how to perform routine

maintenance on your fume hood.

Chapter 7: Modifying Your Protector Premier explains how to modify the fume

hood or add accessories.

Chapter 8: Troubleshooting contains a table of problems you may encounter

while using your laboratory fume hood including the probable causes of the

problems and suggested corrective actions.

Appendix A: Protector Premier Components contains labeled diagrams of all of

the components of the fume hoods.

Appendix B: Protector Premier Dimensions contains comprehensive diagrams

showing all of the dimensions for the laboratory fume hoods.

Appendix C: Protector Premier Specifications contains the electrical requirements

for laboratory fume hood. Wiring diagrams are also included.

Appendix D: Protector I-S Hood provides information relating to the automatic

Intelli-Sense Blower 3-speed operation.

Chapter 1: Introduction

Product Service 1-800-522-7658

Original instructions

Appendix E: Serial Number Tag Description provides current rating code used on

serial number tag.

Appendix F: References lists the various resources available that deal with

laboratory fume hoods.

Appendix G: VAV Open Area Guidelines to properly assess fume hood effective

area whenever variable air volume (VAV) mechanical systems are installed.

Typographical Conventions

Recognizing the following typographical conventions will help you understand

and use this manual:

Book, chapter, and section titles are shown in italic type (e.g., Chapter 3:

Getting Started).

Steps required to perform a task are presented in a numbered format.

Comments located in the margins provide suggestions, reminders, and

references.

Critical information is presented in boldface type in paragraphs that are

preceded by the exclamation icon. Failure to comply with the information

following an exclamation icon may result in injury to the user or permanent

damage to fume hood.

Les informations critiques sont présentées en gras dans les paragraphes qui

sont précédés par l'icône d'exclamation. Ne pas se conformer aux informations

qui suivent une icône d'exclamation peut résulter à la blessure de l'utilisateur

ou à des dommages irréversibles de la hotte aspirante.

Critical information is presented in boldface type in paragraphs that are

preceded by the wrench icon. These operations should only be performed by

a trained certifier or contractor. Failure to comply with the information

following a wrench icon may result in injury to the user or permanent damage

to your hood.

Les informations critiques sont présentées en gras dans les paragraphes qui

sont précédés par l'icône de clé plate. Ces opérations devraient être seulement

exécutées par un professionnel agrée. L'échec pour se conformer aux

informations qui suivent une icône de clé plate peut résulter à la blessure de

l'utilisateur ou à des dommages irréversibles de la hotte.

Important information is presented in capitalized type in paragraphs that are

preceded by the pointer icon. It is imperative that the information contained

in these paragraphs be thoroughly read and understood by the user.

A number icon precedes information that is specific to a particular model of

laboratory fume hood. The 4' icon indicates the text is specific to the 4-foot

wide model. The 5' icon indicates the text is specific to the 5-foot model, etc.



Chapter 1: Introduction

Product Service 1-800-522-7658

Original instructions

The S icon indicates the text is specific to the standard model.

The A icon indicates the text is specific to the A-Style Combination Sash

Model.

CAUTION –See Manual. When this symbol is on a fume hood it indicates a

caution that is detailed in this manual.

PRUDENCE –Consulter le Manuel. Quand ce symbole est sur une hotte

aspirante, il indique une prudence qui est détaillée dans ce manuel.

CAUTION –Hot Surface.

AVERTIR –Surface Chaude

CAUTION –See Manual. This symbol on the fume hood indicates the

possibility of a pinch hazard.

PRUDENCE –Consulter le Manuel. Ce symbole sur la hotte indique la

possibilité d'un risque de pincement.

Your Next Step

If your Fume Hood needs to be installed, proceed to Chapter 2: Prerequisites to

ensure your installation site meets all of the requirements. Then, go to Chapter 3:

Getting Started for instructions on how to install your laboratory fume hood and

make all of the necessary connections.

If you would like to review how laboratory fume hoods operate, go to Chapter 4:

Performance Features and Safety Precautions.

For information on the operational characteristics of your laboratory fume hood,

go to Chapter 5: Using Your Protector Premier.

If your laboratory fume hood is installed and you need to perform routine

maintenance on the cabinet, proceed to Chapter 6: Maintaining Your Protector

Premier.

For information on making modifications to the configuration of your fume hood,

go to Chapter 7: Modifying Your Protector Premier.

Refer to Chapter 8: Troubleshooting if you are experiencing problems with your

fume hood.

Product Service 1-800-522-7658

Original instructions

CHAPTER 2

PREREQUISITES

Before you install your laboratory fume hood, you need to prepare your site for

installation. Carefully examine the location where you intend to install your

hood. You must be certain that the area is level and of solid construction. In

addition, a dedicated source of electrical power must be located near the

installation site.

Carefully read this chapter to learn the requirements for your installation site:

The location requirements.

The support requirements.

The exhaust requirements.

The electrical power requirements.

The service line requirements.

The space requirements.

Refer to Appendix B: Protector Premier Dimensions for complete fume hood

dimensions.

Refer to Appendix C: Protector Premier Specifications for complete laboratory

fume hood electrical and environmental conditions, specifications and

requirements.

Chapter 2: Prerequisites

Product Service 1-800-522-7658

Original instructions

Location Requirements

The fume hood should be located away from traffic patterns,

doors, windows, fans, ventilation registers, and any other air-

handling device that could disrupt its airflow patterns. All

windows in the room should be closed.

La hotte aspirante devrait être localisé loin des voies de

circulation, des portes, des fenêtres, des ventilateurs, des

bouches de ventilation, et de tout appareil qui pourrait

interrompre ses voies de flux d'air. Toutes les fenêtres dans la

pièce devraient être fermées.

Support Requirements

DO NOT install the fume hood on a cart, dolly, or mobile

bench. ALL Protector Hood installations must be permanent

and stationary. The supporting structure usually consists of a

base cabinet and chemically resistant work surface.

NE PAS installer la hotte aspirante sur un chariot ou un banc

mobile. TOUTES les installations de la Hotte Protecteur

doivent être permanentes et fixes. La structure de soutien

consiste habituellement en un meuble doté d’une surface de

travail chimiquement résistante.

Exhaust Requirements

The exhaust duct connection has been designed for 12" nominal duct (12.75" OD)

to allow for minimum static pressure loss while operating at 60 to 100 fpm face

velocities. The 12" diameter exhaust duct also allows for proper transport

velocities away from the hood in the 1000 fpm to 2500 fpm range. The proper

exhaust volume and static pressure loss are listed next for each hood model:

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Labconco

Labconco

Labconco FreeZone 70061 6L -50C Series Manual de usuario

Labconco

Labconco Purifier Class 2 Biological Safety Cabinet Manual de usuario

Labconco

Labconco Precise CA 5220100 Manual de usuario

Labconco

Labconco RapidVap 73200 Series Manual de usuario

Labconco

Labconco FreeZone 6 Manual de usuario

Labconco

Labconco 5530000 Manual de usuario

Labconco

Labconco FreeZone Plus Manual de usuario

Labconco

Labconco Protector 1204 Series Manual de usuario

Labconco

Labconco CApture 3420000 Manual de usuario

Labconco

Labconco Purifier Axiom 30441 Series Manual de usuario

Labconco

Labconco CentriVap DNA Systems Manual de usuario

Labconco

Labconco Fiberglass 30 Series Manual de usuario

Labconco

Labconco Axiom C1 Manual de usuario

Labconco

Labconco Protector XStream 11041 Series Manual de usuario

Labconco

Labconco Purifier 3951400 Manual de usuario

Labconco

Labconco CentriVap Complete 73150 Series Manual de usuario

Labconco

Labconco Protector 3410000 Manual de usuario

Labconco

Labconco CentriVap-105 Cold Trap Manual de instrucciones

Labconco

Labconco Protector Echo 180 Series Manual de usuario

Labconco

Labconco FreeZone 70020 Series Manual de usuario

Labconco

Labconco CentriVap 73100 Series Manual de usuario

Labconco

Labconco RapidStill I Manual de usuario

Labconco

Labconco Protector 3390000 Manual de usuario

Labconco

Labconco Precise 5220100 Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario