La Crosse Technology WS-7212U Manual de usuario

WS-7212NU

Wireless 433 MHz

Weather Station

Instruction Manual

TABLE OF CONTENTS

Topic Page

Inventory of Contents 3

Additional Equipment 4

Quick Setup Guide 5-9

Function Keys 5

Detailed Set-up Guide 10-15

Battery Installation 10-12

Setting the Time 12-13

Setting °C or °F 13

Setting 12/24 Time 13

Features 14-18

Minimum and Maximum

Temperatures 14

Resetting Minimum and Maximum

Temperatures 14

Adding additional remote

temp/humidity sensors (optional) 15-17

Viewing & operating multiple

remote temperature/humidity

sensors

17-18

Mounting 18-20

Troubleshooting 20-23

Maintenance and Care 24

Specifications 25-26

Warranty Information 27-29

INVENTORY OF CONTENTS

1. One indoor weather

station (Figure 1)

2. The remote

temperature/humidity

sensor (TX4U) and

mounting bracket.

(Figure 2)

3. Mounting hardware.

4. Instruction Manual

and Warranty Card.

Figure 1

Figure 2

ADDITIONAL EQUIPMENT

(not included)

1. 1 Philips screwdriver.

2. 2 Fresh AA 1.5V batteries.

(for indoor weather station)

3. 2 Fresh AA 1.5V batteries.

(for temperature/humidity sensor)

QUICK SET-UP GUIDE

Hint: Use good quality alkaline

batteries and avoid rechargeable

batteries.

FUNCTION KEYS

1. “SET”: Allows you to set the time,

select °C or °F, and select 12 or 24

time display.

2. “MIN/MAX”: Allows you to view the

minimum and maximum

temperatures recorded.

3. “+”: In the set-up display, allows

you to change the hours, minutes,

temperature unit, and 12/24 hour

time display.

4. “CH”: (Channel) Allows you to view

temperature and humidity readings

from up to 3 remote sensors. Each

channel corresponds to one of the

remote sensors. For more

information on Channels see the

“VIEWING AND OPERATING WITH

MULTIPLE REMOTE SENSOR

UNITS” section in the Detailed Set-

Up Guide.

1. Have the indoor weather station and

remote temperature/humidity sensor

3 to 5 feet apart.

2. Batteries should be out of all units

for 15 minutes.

3. Place the batteries into the remote

temperature/humidity sensor first,

then into the indoor weather

station.

(All remote temp/humidity sensors

must be started before the indoor

weather station)

4. DO NOT PRESS ANY BUTTONS

FOR 15 MINUTES.

In this time the indoor weather station

and remote temperature/humidity sensor

will start to communicate with each

other, and the display will show both the

indoor temperature and an outdoor

temperature and humidity. If the indoor

weather station does not display both the

indoor temperature and the outdoor

temperature and humidity after the 15

minutes please re-try the set-up as

shown on page 5.

After both indoor temperature and

outdoor temperature and humidity are

displayed for 15 minutes you can place

your remote temperature/humidity

sensor outdoors and set your time.

Notes on Outdoor Sensor Placement

The remote temperature/humidity sensor

should be placed in a dry, shaded area.

Fog and mist will not harm your remote

temperature/humidity sensor but direct

rain must be avoided.

The remote temperature/humidity sensor

has a range of 330 feet. Any walls that

the signal will have to pass through will

reduce the distance of the range. An

outdoor wall or window can have up to

30 feet of resistance and an interior wall

can have up to 20 feet of resistance.

Your distance plus resistance should not

exceed 330 feet in a straight line.

To complete the set up of your indoor

weather station after the 15 minutes

have passed, please follow the steps

below.

1. Press and hold the “SET” button for

5 seconds.

2. The minutes will now be flashing.

a. Press and release the “+”

button until the correct

minutes are shown.

Note: There is “PM” displayed

to the left of the hour when

between noon and midnight.

During the AM hours this area

will be blank.

b. When the correct minutes

are shown, press and

release the “SET” button

once.

3. The hour will now be flashing.

Press and release the “+”

button until the correct hour is

displayed.

Press and release the SET button

once more, and you are done.

Battery

compartment

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION

A. REMOTE

TEMPERATURE/HUMIDITY

SENSOR

1. Remove the mounting bracket.

2. Remove battery cover

3. Observing the correct polarity, install

2 AA batteries—make sure they do

not spring free, or start-up problems

may occur.

4. Replace cover.

Battery cover

Otros manuales para WS-7212U

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Estación meteorológica de La Crosse Technology

La Crosse Technology

La Crosse Technology S85807 Dimensiones

La Crosse Technology

La Crosse Technology WS-7042TWC Manual de usuario

La Crosse Technology

La Crosse Technology 308-1417 Manual de usuario

La Crosse Technology

La Crosse Technology WS6212 Manual de usuario

La Crosse Technology

La Crosse Technology 308-1415V3 Manual de usuario

La Crosse Technology

La Crosse Technology Wireless Weather Station Manual de usuario

La Crosse Technology

La Crosse Technology WS-1913U-IT Manual de usuario

La Crosse Technology

La Crosse Technology S84060 Manual de usuario

La Crosse Technology

La Crosse Technology 327-1414Wv2 Manual de operación y mantenimiento

La Crosse Technology

La Crosse Technology WS-7211U Manual de usuario

La Crosse Technology

La Crosse Technology Wireless Weather Station Manual de usuario

La Crosse Technology

La Crosse Technology C75747-AU Manual de usuario

La Crosse Technology

La Crosse Technology T83646 Manual de usuario

La Crosse Technology

La Crosse Technology WS-3512 Manual de usuario

La Crosse Technology

La Crosse Technology V50 Manual de usuario

La Crosse Technology

La Crosse Technology C84428 Dimensiones

La Crosse Technology

La Crosse Technology C84428 Manual de usuario

La Crosse Technology

La Crosse Technology WS-9124TWC-IT Manual de usuario

La Crosse Technology

La Crosse Technology WS-7107U Manual de usuario

La Crosse Technology

La Crosse Technology WS-9016U Manual de usuario

La Crosse Technology

La Crosse Technology WS-1612 Manual de usuario

La Crosse Technology

La Crosse Technology 302-604B Dimensiones

La Crosse Technology

La Crosse Technology C84343 Manual de operación y mantenimiento

La Crosse Technology

La Crosse Technology WS-9057U-IT Dimensiones

Manuales populares de Estación meteorológica de otras marcas

Auriol

Auriol AHFL 433 A1 Manual de usuario

NexSens

NexSens G2-HYDROMET Manual de usuario

Hyundai

Hyundai WS 2202 Manual de usuario

IROX

IROX HBVR761 UV-X Manual de usuario

ADE

ADE WS 1711 Manual de usuario

Auriol

Auriol z29592 Manual de usuario

Auriol

Auriol 296289 Manual de usuario

Hyundai

Hyundai WS 2266 Manual de usuario

Ventus

Ventus W177 Manual de usuario

National Geographic

National Geographic VA Colour RC Manual de usuario

Renkforce

Renkforce 1208067 Manual de usuario

Levenhuk

Levenhuk Discovery Report WA40 Manual de usuario

Instant Transmission

Instant Transmission MA 10410 Manual de usuario

Lutron Electronics

Lutron Electronics PHB-318 Manual de usuario

WAREMA

WAREMA EWFS Weather station eco Manual de usuario

TFA

TFA 30.3013.IT Manual de usuario

Alecto

Alecto WS-1200 Manual de usuario

Oregon Scientific

Oregon Scientific RMR966PA Manual de usuario