Oregon Scientific RMR966PA Manual de usuario

RADIO-CONTROLLED PROJECTION

CLOCK WITH NIGHTLIGHT &

INDOOR/ REMOTE THERMOMETER

MODEL NO.: RMR966P/RMR966PU

INSTRUCTION MANUAL

INTRODUCTION

Congratulations on your purchasing the Radio-controlled projection

ClockwithNightlightandIndoor/-RemoteThermometerRMR966P/

RMR966PU.

Theunit is a multi-functional radio-controlled clock. The RMR966P

--- the Central Europe model --- is designed to automatically

synchronize its current time and date when brought within an

approximate 1500km radius of the radio signal generated from

Frankfurt, Germany (DCF-77). The RMR966PU --- the UK model

--- will do the same when brought within range of the radio signal

MSF-60 generated from Rugby, England.

In addition to indoor temperature display, by means of a wireless

remote thermo sensor this unit can simultaneously monitor the

outdoor temperature. The unit can record maximum and minimum

indoor/outdoortemperaturereadings. Nowireinstallationisrequired

between the main and remote units as this unit operates at 433 MHz.

This unit featured with a projection function that allows the user to

display either (1) the Current Time with Indoor Temperature or (2)

Current time with Outdoor Temperature on the ceiling, wall or other

flat surface. The image projected is in a deep red color which is

easily seen in the dark.

The Projection Clock also comes with favourable features such as

Auto-on/off Nightlight, EL back-light, hourly-chime function and

dual daily alarm with 8-minute snooze function and Pre-Alarm

function.

KEY CONFIGURATION & FEATURES:

MAIN UNIT

FRONT VIEW

A8 A5

A7 A6

A1 3-Line LCD Display

Displays the time, date and temperature

A2 [ ] Battery-low indicator

Displays when battery power of main unit is low

A3 [ ] Battery-low indicator

Displays when battery power of remote sensor is low

A4 [ ] Radio-reception icon

Indicates the strength of the reception of clock radio signal

A5 [IN/OUT TEMP] BUTTON

-Press to toggle between the Indoor and Outdoor temperature

display

-Press and hold for 2 seconds to activate the auto-search for

remote thermo signal

A6 [MEM] BUTTON

-Press to toggle among current, maximum and minimum

temperature records

-Press and hold for 2 seconds to erase the memories

A7 [ALARM/*] BUTTONS

-Press to display the alarm-1 or alarm-2 function

-Press and hold for 2 seconds to enter the corresponding

alarm time setting mode

A8 [MODE] BUTTON

-Press to toggle among the calendar clock display modes

-Press and hold for 2 seconds to enter the clock setting mode

A9 [ & ] BUTTONS

-Press to increase/ decrease the values in setting modes

-Press and hold for 2 seconds to activate/ deactivate the

autoreception of RF clock radio signal

TOP VIEW

B1 [SNOOZE/ LIGHT] BUTTON

-Pressto turn on the ELbacklight and projection for 5seconds

-Presstochangetheprojectedtemperature(IndoororOutdoor)

when projection is On

-Press to stop the alarm sound and activate the 8-minutes

Snooze function

B2 [LIGHT AUTO-ON-OFF] SLIDE BUTTON

Slide to select the different mode for the Nightlight

B3 LIGHT SENSOR

B4 ROTATABLE NIGHTLIGHT

B4 B3

BACK VIEW

C1 [180º ROTATION] BUTTON

Press to flip the projected image horizontally

C2 [FOCUS] KNOB

Rotate to adjust the focus of projection

C3 [IMAGE ROTATION] KNOB

Rotate to change the image 90º to the left or right

C4 [PROJECTION ON ] BUTTON

Slide to enable continuous projection (when Adapter is

connected)

C5 BATTERY COMPARTMENT

Accommodates 2 pieces of UM-3 or AA 1.5 V batteries

C6 [RESET] BUTTON

Press to return all settings to default values

C7 [+ LIGHT SENSOR -] KNOB

Rotate to adjust the sensitivity of the light sensor

C8 [˚C / ˚F ] BUTTON

Selects between Centigrade (°C) and Fahrenheit (°F)

BOTTOM VIEW

D1 4.5 V DC JACK

ForAC power adapter installation

KEY CONFIGURATION AND

FEATURES:REMOTE THERMO UNIT

THR228NS

A. LCD

Displays the current temperature monitored by the remote unit

B. LED INDICATOR

Flashes when the remote unit transmits a reading

C. °C/°F SLIDE SWITCH

Selects between Centigrade (°C) and Fahrenheit (°F)

D. RESET BUTTON

Returns all settings to default values

E. BATTERY COMPARTMENT

Accommodates two UM-4 or AAA size 1.5V batteries

F. BATTERY DOOR

G. WALL-MOUNT HOLDER

Supports the remote unit in wall-mounting

H. REMOVABLE TABLE STAND

For standing the remote unit on a flat surface

BATTERY INSTALLATION:MAIN UNIT

This unit can be operated by batteries orAC power alone as well as

both together.

Battery Installation:

1. Remove the battery compartment door by rotating it to the

direction of “Open ” as shown

2. Insert two pieces of UM-3 orAA 1.5V batteries in accordance

to the polarities.

3. Press [RESET].

4. Replace the battery compartment door by rotating it back onto

the unit by following the direction of “Close ”.

When the battery power level is low, the respective low battery

indicator [ ] will light up. Replace the batteries or connect it

with AC power adapter

PleasenoteifonlyACadapterisconnectedandnobatteryisinstalled,

low battery indicator [ ] for main unit will also light up.

Using AC Power

BATTERY INSTALLATION : REMOTE UNIT

1. Place both main and remote units as close as possible to each

other.

2. Remove the screws on the battery door of the remote unit.

3. Select the units of measurement for the temperature display on

the °C/°F slide switch.

4. Install2batteries (UM-4 or "AAA" size 1.5V) strictly according

to the polarities shown.

5. Insert batteries or press the reset button of the main unit.

6. Replace the battery compartment door and secure its screws.

7. Position the remote sensor and main unit within effective

transmission range, which in usual circumstances, is 30 meters.

Though the sensor is weather resistant, and is meant for use outside,

it should be placed away from direct sunlight, rain, or snow.

Note: The effective range may be limited by building materials and

the position of either the main unit or remote sensors. Try various

set-up arrangements for best result.

REMOTE UNIT : WALL-MOUNTING OR

TABLE STANDING

Wall-mount Table Stand

FEATURES

Section I — Radio-Controlled Digital

Calendar Clock

ABOUT RADIO RECEPTION

ImportantNote:Since this unit can also receiveremotetemperature

data from the remote unit, after battery installation, the unit will

FIRST search for the remote temperature data which may last for

up to 4 minutes. Upon successful reception of the remote data,the

unit will then automatically synchronize its time and date with the

radio signal when it is within reception range of the signal.

When the unit is receiving radio signal, the reception icon will start

toblink.Thereceptioniconwillshow either strong or weak reception

depending on the strength of the radio signal.A complete reception

generally takes about two to ten minutes.

When the reception is complete the reception icon will stop

blinking. The reception icon will show as “ ” for no reception or

“ ” for successful reception.

STRONG

WEAK

NO RECEPTION

IN PROGRESS

For best reception, place the unit away from other equipment that

emit radio frequency or microwave signals such as TVs, radios, PCs

or microwave ovens. Other causes for signal interference include

electrical power transmission tower and/or steel reinforced concrete

construction.

HOW TO ENABLE OR DISABLE AUTO -

RECEPTION

To disable the automatic reception of radio signal, press and hold

[ ] for 2 seconds. The reception icon will disappear and the unit

will stop receiving the radio signal.

To activate the signal reception again, press and hold [ ] for 2

seconds. The reception icon will appear again and start blinking to

indicate auto reception of radio signal.

Note: this activation function will be temporarily disabled when

the main unit is searching for the remote temperature data right

after battery installation or Reset.

DISPLAY MODES SELECTION

Press [MODE] in the normal display mode to scroll through the

calendar clock display modes:

1. Clock with Second

---------------------------

Indoor Temperature

2. Clock with Weekday

---------------------------------------------

Day-Month

3. Clock with Weekday

--------------------------------------------------------

Clock (2nd Zone-time)

4. Clock with Weekday (2nd Zone-time)

--------------------------------------------------------

Calendar (2nd Zone-time)

SETTING THE CLOCK AND CALENDAR

MANUALLY

When the automatic radio reception is disabled, the main unit can

be set manually. Set the Clock and Calendar by following the

procedures below:

1. Press and hold [MODE] for 2 seconds. The 2nd Zone-time

hour offset will start flashing.

2. Enter the hour-offset by using [ ] or [ ]. Press [MODE]

to confirm the entry.

3. Follow the same procedures to set the 12/24-format, hour,

minutes, year, “mm:dd” or “dd:mm” calendar display format,

month, day, display languages and hourly chime on/off mode.

4. Press [MODE] to save the changes and exit the setting mode.

If changes are made after the minute adjustment, the value of

seconds will be reset and start from zero.

5. For the day-of-week you can select among 5 languages —

English (E), French (F), German (D), Italian (I) and Spanish

(S).

ALARM & PRE-ALARM FUNCTION

This unit has two alarms (Alarm-1 and Alarm-2) which can be

operated together or independently.

To activate or deactivate the alarm, press the [ ] or [ ] button

when the respective alarm is being displayed. “-:--“ will be shown

when the alarm is being deactivated. [ ] or [ ] will be shown

when the respective alarm is activated.

When an alarm is activated, it will go off at the preset time. The EL

backlight and projection will activate for 5 seconds and the alarm

sounds will be given out for 2 minutes.

To stop the alarm, press any key. When the [SNOOZE/LIGHT]

button is pressed to stop the alarm sound, the snooze function will

be activated and the alarm will go off again after 8 minutes. To

disable the snooze function, press and hold the [SNOOZE/LIGHT]

button for 3 seconds or press other key to stop the alarm sound.

If a second alarm goes off when the first alarm is sounding off, the

first alarm will be disabled automatically.

(a) To set the alarm:

1. Press the [ALARM/*] button once to select Alarm-1 or again

to select Alarm-2.

2. Press and hold the [ALARM/*] for 2 seconds to enter the

alarm time setting mode. The hour will be flashing.

3. Enter the hour using the [ ] or [ ] button.

4. Press the [ALARM/*] and the minute will be flashing.

5. Enter the minute using the [ ] or [ ] button.

6. Press the [ALARM/*] to confirm the alarm time and enter the

pre-alarm setting mode. “PRE-AL” icon will be shown.

PRE-ALARM FEATURE FOR REMOTE SENSOR

The alarm function also has a pre-alarm feature which can alert the

user before the preset alarm time when weather condition changes.

This Pre-alarm function applies with Remote sensor only.

(b) To set the Pre-alarm:

1. After setting the alarm time (as indicated above) the unit will

enterthePre-alarm setting mode automatically. “PRE-AL” icon

will be shown and the time-interval will be flashing.

2. Use the [ ] or [ ] button to select the operating time

interval for this pre-alarm function. You can choose from “00”,

“15”, “30”, “45” and “60” minutes.

3. Press the [ALARM/*] to confirm and exit. The pre-alarm

function will be enabled automatically which is indicated by

the appearance of the [*] symbol.

4. To disable this pre-alarm function, select the time interval as

“00”.

The pre-alarm feature will operate during the selected time-interval

before the preset alarm time.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Estación meteorológica de Oregon Scientific

Oregon Scientific

Oregon Scientific BAR888Ra Manual de usuario

Oregon Scientific

Oregon Scientific BAA938HG Manual de usuario

Oregon Scientific

Oregon Scientific BAR112HGLA Manual de usuario

Oregon Scientific

Oregon Scientific BA900 Manual de usuario

Oregon Scientific

Oregon Scientific RAR502SX Manual de usuario

Oregon Scientific

Oregon Scientific BAR988HG Manual de usuario

Oregon Scientific

Oregon Scientific PRYSMAchrome BAR292A Manual de usuario

Oregon Scientific

Oregon Scientific BAR618HGA Manual de usuario

Oregon Scientific

Oregon Scientific BAR626 Manual de usuario

Oregon Scientific

Oregon Scientific BAR636 Manual de usuario

Oregon Scientific

Oregon Scientific BAR933HG Manual de usuario

Oregon Scientific

Oregon Scientific BAR321HGN Manual de usuario

Oregon Scientific

Oregon Scientific BAR826HG Manual de usuario

Oregon Scientific

Oregon Scientific WMR200 Manual de usuario

Oregon Scientific

Oregon Scientific WMR200 Manual de usuario

Oregon Scientific

Oregon Scientific BAR916HG Manual de usuario

Oregon Scientific

Oregon Scientific BBW213 Manual de usuario

Oregon Scientific

Oregon Scientific BAR898HGA Manual de usuario

Oregon Scientific

Oregon Scientific Starck PSM06A Manual de usuario

Oregon Scientific

Oregon Scientific WMR200 Manual de usuario

Oregon Scientific

Oregon Scientific Clima Control RMR500 Manual de usuario

Oregon Scientific

Oregon Scientific RAR213HGX-01 Manual de usuario

Oregon Scientific

Oregon Scientific BA169 Manual de usuario

Oregon Scientific

Oregon Scientific WMR100 Manual de usuario

Manuales populares de Estación meteorológica de otras marcas

Auriol

Auriol AHFL 433 A1 Manual de usuario

NexSens

NexSens G2-HYDROMET Manual de usuario

Hyundai

Hyundai WS 2202 Manual de usuario

IROX

IROX HBVR761 UV-X Manual de usuario

La Crosse Technology

La Crosse Technology C86371 Manual de usuario

ADE

ADE WS 1711 Manual de usuario

Auriol

Auriol z29592 Manual de usuario

Auriol

Auriol 296289 Manual de usuario

Hyundai

Hyundai WS 2266 Manual de usuario

La Crosse Technology

La Crosse Technology WS-2210 Manual de usuario

La Crosse Technology

La Crosse Technology WS-811561 Manual de usuario

Ventus

Ventus W177 Manual de usuario

National Geographic

National Geographic VA Colour RC Manual de usuario

Renkforce

Renkforce 1208067 Manual de usuario

Levenhuk

Levenhuk Discovery Report WA40 Manual de usuario

Instant Transmission

Instant Transmission MA 10410 Manual de usuario

Lutron Electronics

Lutron Electronics PHB-318 Manual de usuario

WAREMA

WAREMA EWFS Weather station eco Manual de usuario