La Crosse Technology WS-2310 Hoja de especificaciones

Quick Set Up Manual – WS-2310 Weather Station

Using cable connection or 433MHz for wireless transmission of weather data, this unique weather station can be powered

using batteries or AC power (or both at the same time) for all your weather needs in the home or office.

Carefully open and check that the following contents are complete:

Item: Consisting of: Fittings: Illustration:

Base Station 1) Main unit

1) AD/DC 120V power Adaptor -

optional use (included)

Thermo-Hygro

Sensor 1) Main unit

2) Rain protection cover

1) 32ft cable - optional connection to

the base station (included)

2) Wall mounting screws

3) Plastic anchors for screws

Wind Sensor 1) Main unit with wind vane

2) 32ft cable (already attached the

main unit)

3) Mast holder

1) 2 x U-bolts for mast holder

2) 4 x Washers

3) 4 x Nuts

4) 1 x screw (to secure main unit to the

mast holder)

Rain Sensor 1) Base and funnel

2) 32ft cable (already attached

the main unit)

‘Heavy

Weather” PC

software

CD-ROM

(English and German version only) 1) 6.5 ft computer cable for PC

function only - optional use

(included)

Setting Up:

Important: Operating power is supplied to both the wind and rain sensors by the thermo-hygro sensor

Setting up using batteries:

1) Sensors: Pull and remove the protective rain cover to reveal three socket ports and the battery cover. Insert the cables

of the wind and rain sensors in the correctly marked sockets. Slide open the battery compartment and checking the

correct polarity insert 2 x AA 1.5V batteries and replace the cover and rain cover

2) Base Station: Now open the battery cover at the back of the unit and checking the correct polarity insert 3 x AA 1.5V

batteries and replace the battery cover

Setting up using the AC/DC power adaptor:

1) Sensors: Set up the sensors as described above in Setting up using batteries.

2) Base Station: Using the AC power adaptor (included in this set) plug it into mains supply and connect it to the 6.0V DC

adaptor socket located at the side of the base station.

Performing a function test:

After powering up the units, the base station has to synchronize to the sensors before the weather data can be received.

The synchronization mode lasts for 15 minutes. Pressing the MIN/MAX key at any time will send the base station into the

WWVB radio controlled time reception mode. Under normal conditions the radio controlled time is usually received within 3-

5 minutes before returning to the normal operation. During the synchronization mode, perform the following function test to

check operation:

              

Thermo-Hygro Sensor

Battery Cover

Battery Compartment Sensor sockets

Base Station

Battery compartment PC COM Port

Socket for sensor

DC 6.0V

socket

1) Check that the wind-vane and fan of the wind sensor can freely rotate by moving the vane gently and also blowing into

the fan to emulate wind speed and direction

2) Holding the rain sensor in both hands with the longest side facing you, tilt the unit from side to side and hear the rain

counter flip which emulates rainfall

3) The base station will start to receive the 433MHz data transmitted from the sensors. Data such as rainfall will not be

updated as regularly as the outdoor temperature since it does not rain constantly all the time. Therefore these readings

may take up to two minutes before being shown on the LCD.

4) Now using the DISPLAY key on the base station, toggle between different weather modes on the LCD to check that the

weather readings can be received for the relevant sections, for example outdoor temperature and humidity and etc.

Note: Should any outdoor data not be received from the sensors (when “- - -“ is displayed), check all cables are correctly

inserted and/ or the batteries or AC cord are plugged in, press and hold the PLUS(+) key for 2 seconds to hear a beep and

the base station will synchronize to the sensors transmitting signal. Wind speeds that read zero does not mean reception

failure, it simply means that there was no wind at the time of reading the data.

Mounting the units:

Users must take their surroundings into consideration before deciding which method is best suited for them. Connection by

cable is advantageous in that data from the sensors to the base station is interference free. Using 433MHz wireless

transmission gives users little restriction on placement as that all units can be positioned virtually anywhere to within a 100ft

radius of the base station. You must decide which method is best suited to you. For cable connecting, please ensure that

the 10 meters cable included in this set meets with your distance requirements (see accessories in the main user manual for

adding extension cables).

To change from 433MHz to cable connection (or vice versa) simply connect (or disconnect) the 32ft cable from the base

station to the sensor. The base station will automatically detect the connection and read the weather data. If the data

cannot be received then press and hold the PLUS(+) key for 2 seconds to synchronize the base station with the sensor.

Important: Ensure all signals including the radio controlled time can be received and/or all cable distances meet with your

requirements at the point of fixing particularly before you start drilling any mounting holes.

Wind sensor

Secure the main unit to the shaft of the mast holder using the single screw provided with the front of the sensor (marked E)

facing in the East-West direction otherwise wind direction will not be accurate. Now fix the entire unit to a suitable mast

using the 2 two U-bolts, 4 washers and nuts found in this set.

Note: For best results mount the wind sensor onto a mast to allow the wind to freely travel from all directions to enable an

accurate reading (ideal mast size should be from Ø6.3” – Ø1.3”). Ensure that the 10 meter cable of the wind sensor meets

your distance requirements.

Rain sensor

The rain sensor should be mounted horizontally about 2-3ft off from the ground in an open area away from trees or other

coverings to allow rain to fall naturally for an accurate reading.

Note: For best results ensure the base is horizontal to allow maximum drainage of any collected rain

Thermo-hygro Sensor

To wall mount the thermo-hygro sensor, fix the wall holder onto the desired wall (2 screws are supplied), plug the sensor

firmly into the wall holder and then carefully replace the rain cover back over the thermo-hygro sensor.

Note: After mounting the units, should the weather data not be received then press and hold the PLUS(+) key for 2 seconds

to synchronize the base station with the sensor.

Weather station for use with your PC

Use your PC to read the latest weather data collected by the weather station. Just simply install the software from the

enclosed CD-ROM onto your PC. For full details see the “Heavy Weather “ PC software instructions in the CD-ROM

(English version only).

System Requirements:

The minimum system requirement for use of “Heavy Weather” PC software is:

•Operating system: Windows 98 or above

•Processor: Pentium 166 MHz or above processor

•RAM: 32MB or above

•Hard-disc: 20MB free space

•CD-ROM drive

Operation Manual

Professional Remote Weather Station

This Operation Manual is part of this product and should be kept in a

safe place for future reference. It contains important notes on setup and

operation.

Please see www.heavyweather.info for a complete IM, FAQ and

downloads of the most current software.

Table of Contents

Page

1. Introduction………………………………………………..........

2. Intended use……………………………………………………..

Weather Station…………….................................................

System requirements for PC use…………...........................

Features of the base station…………..................................

Features of the wind sensor………… ..................................

Features of the rain sensor..................................................

3. Safety Notes........................................................................

4. Packaged contents ..............................................................

5. Setting up.............................................................................

6. Operation using cable connection or

wireless 433MHz .................................................................

7. LCD overview ......................................................................

8. Function test........................................................................

9. Mounting..............................................................................

10. Resetting & factory settings.................................................

11. Function description.............................................................

12. Operation keys.....................................................................

13. Basic programming modes..................................................

14. MIN/MAX programming modes............................................

15. Alarm programming modes..................................................

16. Auto-memory for stored values............................................

17. Accessories: extensions cables...........................................

18. Changing batteries...............................................................

19. Problems and interference with operation............................

20. Transmission range .............................................................

21. Cleaning and maintenance..................................................

22. Specifications.......................................................................

WIRELESS

WEATHER STATION

1. Introduction

Thank you for purchasing this Professional Remote Weather Station.

Designed for everyday use, the weather station will prove to be an

asset of great value for your personal use in the home or office.

Please read this instruction manual thoroughly to fully understand the

correct operation of your weather station and benefit from its unique

features.

2. Intended Use

Weather Station

The base station measures the indoor environment of its surrounding

area and receives weather data from the following three outdoor sen-

sors:

1) Thermo-Hygro Sensor

2) Wind Sensor

3) Rain Sensor

The received data is continuously updated to bring you the latest

weather information on the base station’s LCD. The outdoor thermo-

hygro sensor is the main data communication unit since both the wind

and rain sensors are connected to the thermo-hygro sensor for oper-

ating power and rely on it to communicate to the base station.

Weather data sent from the thermo-hygro sensor can be done by

wireless 433MHz transmission (up to 100ft in open space) or by cable

connection.

Using the enclosed 6.5ft computer cable and CD-ROM, you can in-

stall the Heavy Weather software to your PC and access the latest

weather information from your PC and upload up to 175 sets of re-

corded weather data received by the base station. Recorded data

can be used to generate statistics and charts onto your spreadsheets

(175 sets of data is stored in the base even if the PC is switched

OFF). The software itself does not set any limits as to how many data

sets can be transferred to PC.

This weather station is designed to work easily with your PC, simply

connect and disconnect the PC cable at any time.

System Requirements for PC use:

The minimum system requirement for use of this “Heavy Weather”

software is:

Operating system: Windows 98 or above

Processor: Pentium 166 MHz or above

RAM: 32MB of RAM or above

Hard disk: 20MB free space

CD-ROM drive

For full details on operation and installation of the “Heavy Weather”

software refer to the PC manual in PDF format on the CD-ROM.

Features of the base station:

•Receives and displays the WWVB radio controlled time and date

•Display of extensive weather data, in all cases with programmable

alarm functions for certain weather conditions as well as records of

all minimum and maximum values along with time and date of their

recordings

•Indoor and outdoor temperature displays in degrees Fahrenheit or

Celsius (user selectable)

•Indoor and outdoor relative humidity displays

•Air pressure reading in inHg or hPa, absolute or relative (user select-

able)

•Detailed display of rainfall data in 1 hour, 24 hours, total since last

reset (user selectable in mm or inch)

•Wind speed in mph, km/h, m/s, knots or Beaufort (user selectable)

•Wind direction display with LCD compass as well as numerical (e.g.

225°) and abbreviated characters (e.g. SW)

•Wind chill temperature display

•Dew point temperature display

•Weather forecast display by weather icons (sunny, cloudy, rainy)

•Weather tendency indicator

•Storm warning alarm

•LED back light

•Simultaneous display of all weather data with individual settings by

the user

•COM port for easy connection to your PC

•All the weather data from the base station and up to 175 sets of

weather history data with user adjustable measuring intervals can be

recorded and uploaded to your PC

Features of the Thermo-Hygro Sensor

The thermo-hygro sensor measures the outdoor temperature and

relative humidity. It also collects the readings from the rain and wind

sensors before transmitting the data to the base station by wireless

433MHz or by the 32ft cable included in this set.

Features of Wind sensor

The wind sensor measures wind speed and wind direction and sends

the data to thermo-hygro sensor, which in turn transmits the data to

the base station. Operating power is taken from the thermo-hygro

sensor using a 32ft cable connection.

Features of Rain sensor

The rain sensor measures the rainfall and sends the data to thermo-

hygro sensor, which in turn transmits the data to the base station.

Operating power is taken from the thermo-hygro sensor by a 32ft

cable connection.

3. Safety Notes

•Damage caused by failure to comply with this instruction manual will

invalidate any guarantee! The manufacturer and supplier will not be

held liable for damages due to failure to comply with this instruction

manual or from data inaccuracies that may occur with this product!

•In case of harm or damage to a person or property caused by im-

proper handling or failure to comply with this instruction manual, the

manufacturer and supplier cannot be held liable.

•For reasons of safety and operation, alterations to this device are

strictly prohibited.

•To operate the weather station, use only supplied adaptor and batter-

ies of the recommended type.

•Do not leave discharged batteries in the device as these may corrode

and release chemicals that may damage the unit.

•Inserting batteries in an incorrect polarity will cause damage to this

product.

•This product is not a toy kept out of the reach of children.

•Do not dispose of new or used batteries in a fire as they may explo-

sion or release dangerous chemicals.

•This product is not to be used for medical purposes or for public

information.

4. Packaged Contents

Before setting up, carefully unpack the contents onto a table or flat

surface and check that the following are complete:

Item: Consisting of: Fittings: Illustration:

Base

Station •Main unit

•AD/DC 120V power

Adaptor - optional use

(included)

Thermo-

Hygro

Sensor

•Main unit

•Rain protection

cover

•32ft cable - optional

connection to the

base station (in-

cluded)

•Wall mounting screws

•Plastic anchors for

screws

Wind

Sensor •Main unit with

wind vane

•32ft cable

(already at-

tached to the

main unit)

•Mast holder

•2 x U-bolts for mast

holder

•4 x Washers

•4 x Nuts

•1 x screw (to fix main

unit to the mast holder

Rain

Sensor •Main unit (base

and funnel)

•32ft cable

(already at-

tached to the

main unit)

Heavy

weather

soft-

ware

CD-Rom format

(English and

German lan-

guage)

•6.5ft PC cable for PC

connection - optional

use (included)

5. Setting up

First, choose to use the adaptor (included in this set) or batter-

ies for operation. Both these methods allow for operation us-

ing wireless 433MHz transmission or cable connection be-

tween the base station and the sensors and setting up for both

methods is as follows:

Base Station:

Setting up using batteries:

Important: To avoid operating problems, please take note of bat-

tery polarity if inserting any batteries

1) Pull away the rain cover of the thermo-hygro sensor to reveal the

three sockets (for the wind sensor, rain sensor and the base sta-

tion)

2) Connect the attached cables of wind and rain sensors to the

corresponding sockets of the thermo-hygro sensor by clicking

them into place

3) Open the battery cover of the thermo-hygro sensor located below

the three sockets and insert 2 x AA, IEC LR6, 1.5V batteries and

close the cover

4) Open the base station’s battery cover located at the back of the

unit and insert 3 x AA, IEC LR6, 1.5V batteries into the battery

compartment and close the battery cover

Sensor sockets

Battery compartment

Socket for

Thermo-Hygro

Sensor

Socket for

Adaptor

PC COM

Port

Battery

Compartment Battery Cove

Thermo-Hygro Senso

Sensor sockets

Setting up using the AC adaptor:

1) Power up all the sensors as described in setting up using batter-

ies above

2) Using the AC adaptor (included), plug it into the mains outlet and

power up the base station by inserting the adaptor jack into the

DC 6.0V socket located on the side of the base station

Every time the thermo-hygro sensor is powered up (for example after

a change of batteries), a random security code is transmitted and this

code must be synchronized with the base station to receive weather

data.

When the base station is powered up, a short beep will sound and all

LCD segments will light up for about 5 seconds before it enters into a

15 minute learning mode to learn the sensors security code. After the

learning mode (or by pressing the MIN/MAX key at anytime), the base

station will start the WWVB radio controlled time reception.

Note for WWVB Radio Controlled Time:

The time and date display is based on the signal provided by the

highly accurate government operated atomic clock in Ft. Collins,

Colorado. This radio-controlled clock does not only provide for the

weather station’s time and date display but also functions as the time

and date source for all of this weather station’s memory and history

values using time and date information.

LCD backlight:

When using the power adaptor, the LCD backlight is switched on

continuously. Under battery operation, the LCD backlight is switched

on for 15 seconds intervals when any key is pressed.

6. Operation using cable connection or wireless 433MHz

Cable Connection:

Using this method of operation will provide interference free transfer

of the weather data from the sensors to the base station. The data

sending interval from the sensors to the base station will also be more

frequent compared to using 433MHz transmission and will result in

higher power consumption. Therefore batteries will have a shorter life

span for cable connection compared to using 433MHz.

To operate using cable connection, simply use the enclosed 32ft

cable and connect the thermo-hygro sensor to the base station. Once

the connection is detected, the base station will automatically con-

tinue reading the data from the sensor.

The user may at any time switch from cable connection to using

433MHz (or vice versa) by simply disconnecting (or connecting) the

cable from the base station to the sensor. When the base station

detects no cable connection to the sensors the base station will auto-

matically change to using 433 MHz for reception of the weather data

from the sensors.

The data receiving intervals are as follows:

-Using cable connection data is updated every 8 seconds.

-Using wireless 433 MHz data is updated from 16 to 128 second

intervals depending on wind speed and rain activity.

Using the AC adaptor to operate the base station will also supply

power to the sensor if the cable is connected to it. Batteries used for

433MHz transmission may be left in the sensor when using cable

connection for power back up in case of AC power failure. A loss of

power would desynchronize the base station and the sensor and no

weather data will be received. To Synchronize the units so that the

weather data can be received, press and hold the PLUS (+) key for 2

seconds. However in general, batteries that will not be used for long

periods should be removed to avoid leakage.

Wireless 433MHz transmission:

Using 433MHz wireless transmission of weather data from the sensor

to the base station will provide users greater freedom as to where

units can be positioned without the need to be restricted by cable.

Note:

If no outdoor weather data is displayed or the signal to the sensors is

lost during setting up, mounting, changing of batteries to the sensor or

plugging or unplugging cables, simply press and hold the PLUS (+)

key for 2 seconds and a short beep will sound to synchronize the

base station to sensors. Without being synchronized, weather data

will not be received.

1. Low battery indicator

2. WWVB radio controlled time icon

3. Date display

4. Time zone display

5. Date, seconds, alarm time and time

zone

6. Alarm icon

7. Weather forecast icons

8. Weather tendency indicator

9. Pressure alarm display

10. hPa/inHg air pressure unit

11. Pressure units (relative or absolute)

12. 433MHz reception icon

13. Rainfall display

14. Indoor, outdoor, humidity, dew point,

wind chill, rainfall alarm icon

15. 24h, 1h or total hour display

16. Humidity display as RH%

17. Rainfall units (inch or mm)

18. Temperature display units (ºC or ºF)

19. Outdoor temperature/humidity display

20. Indoor temperature/humidity display

21. Dew point temperature display

22. Wind chill temperature display

23. Wind alarm icon

24. Wind information for Min/Max speed

and wind speed low, high, direction

alarm

25. Wind direction and speed (m/s, knots,

Beaufort, km/h or mph) display

26. Alarm buzzer ON/OFF icon

27. General alarm icon

7. LCD Overview

The following illustration shows the full segments of the LCD for

description purposes only and will not appear like this during

normal operation and use.

8. Function test:

Once the weather station is powered up, perform a function test by

checking that the weather data is received. To do this, press the

DISPLAY, PRESSURE or WIND keys to toggle through the relevant

LCD sections:

1) Indoor temperature and humidity

2) Outdoor temperature and humidity

3) Outdoor wind chill

4) Dew point

5) Rainfall 24 hour

6) Rainfall 1hour

7) Rainfall Total

8) Relative and absolute pressure

9) Wind speed, wind direction and wind direction in degrees

If any readings cannot be received from the sensors, lines (- - -) will

be displayed in the respective weather sections of the LCD. In this

case, check that all cables are correctly inserted into the correct

sockets and/or check the batteries in the outdoor thermo/hygro sen-

sor and press and hold the PLUS (+) key for 2 seconds and a short

beep will sound to synchronize the base station to the sensors other-

wise no weather data will be received.

Some weather readings such as wind speed and direction may not

appear immediately on the LCD if the wind-fan or vane of the wind

sensor is moved. This is due to the set reading time intervals for the

wind readings. However the current wind speed or direction will be

displayed once the time reading interval is reached. For rainfall, the

interval readings may take up to 2 minutes before the data is dis-

played on the LCD.

9. Mounting

Important Note

Prior to drilling mounting holes and permanently affixing any of the

units, please ensure the following points are considered:

•Cable lengths of the units meet with your distance requirements

at the point of fixing

1 2 3 4

7 8

9 10

13 12

14 15

19 20

26 27

•Signals from the sensors can be received by the base station at

points of mounting

•Radio controlled time signal can be received at the point of

mounting

NOTE: The WWVB receiver is located in the base station.

Base Station

With two foldable legs at the back of the unit, the base station can be

placed onto any flat surface or wall mounted at the desired location by

the hanging holes also at the back of the unit. It is important to check

that the 433MHz (if using wireless connection) and the WWVB radio

controlled time signal can be received before permanently mounting

any of the units. Should the base station not display the 433MHz

weather data from the sensors or the radio controlled time from the

desired location, then relocate the units. Once the signals are re-

ceived, the system can be affixed. Also if you have selected to use

cable connection, ensure that distances can reach all desired loca-

tions before affixing any unit permanently

NOTE: For reception of WWVB time/date signal, do not mount

the base station closer than 5 feet from a computer, florescent

lights or other electrical appliances. Do not mount the base

station on a wall that has metal heat/AC ductwork in the wall

behind the base station. For best WWVB reception place the

base station near a window facing Colorado. WWVB reception

will be obtained easiest in the nighttime hours when the

WWVB signal is strongest.

Mounting the Wind Sensor onto a mast

Firstly, check that the wind-fan and the wind-vane can rotate freely

before fixing the unit. For correct and accurate readings it is impor-

tant to mount the sensor so that the front (marked E) is pointing in

East-West direction. The wind sensor should now be mounted using

the screw provided onto a mast to allow the wind to travel around the

sensor unhindered from all directions (ideal mast size should be from

Ø.63” – Ø1.3”).

Once the wind sensor is fixed onto the mast, connect the cable to the

corresponding thermo-hygro sensor socket so that operating power

supply can be received and data can be transmitted to the base sta-

tion.

Mounting the Rain Sensor

For accurate results, the rain sensor should be securely mounted

onto a horizontal surface about 2-3ft above the ground and in an open

area away from trees or other coverings where rainfall may be re-

duced causing inaccurate readings.

When securing into place, check that rain excess will not collect and

store at the base of the unit but can flow out between the base and

the mounting surface (test by pouring clean water).

Base portion

Funnel portion

Wind-fan

Wind-vane

Mast

After mounting the rain sensor, connect the cable to the thermo-hygro

sensor at the corresponding socket so power supply can be received

and data be transmitted to the base station

The rain sensor is now operable. For testing purposes, very slowly

pour a small amount of clean water into the rain sensor funnel. The

water will act as rainfall and will be received and displayed at the

base station after about 2 minutes delay i.e. when the reading interval

is reached (to clear this testing data on the base station, refer to the

section “MIN/MAX Mode” below).

Mounting the thermo-hygro Sensor

An ideal mounting place for the thermo-hygro sensor would be the

outer wall beneath the extension of a roof, as this will protect the

sensor from direct sunlight and other extreme weather conditions.

To wall mount, use the 2 screws to affix the wall bracket to the de-

sired wall, plug in the thermo-hygro sensor to the bracket and secure

both parts by the use of the supplied screw and ensure that the ca-

bles from the wind and rain sensors are correctly plugged in other-

wise data transmission errors could occur.

NOTE: For best 433 MHz reception mount the thermo-hygro sen-

sor on an outside wall near the location of the base station.

10. Resetting & factory settings:

As previously mentioned, in the event of a power reset to the sensor

(for example a change of batteries), the base station has to synchro-

nize to the sensor again otherwise no weather data will be received.

To do this, simply press and hold the PLUS (+) key for 2 seconds and

a short beep will sound to synchronize the base station to the sensor.

When the units are synchronized, the data will be received again and

the base station will return to normal operation mode.

Do not remove batteries or unplug the AC adaptor of the base station

otherwise all 175 sets of recorded weather history data for transfer-

ring to the PC will be lost (for full details of PC use, please see PC

user manual in the enclosed Heavy Weather CD-ROM).

However if you wish to make a full reset of the base station and return

to the original factory settings, simultaneously press and hold the

PRESSURE and WIND keys for about 5 seconds. The base station

will beep once and the entire LCD will light up for 5 seconds and go

back to the original factory settings. This process with clear all previ-

ous user defined values and all weather history recordings.

Factory default settings:

The following table shows the factory default values of the weather

station:

Matter: Default Setting:

Time 0:00

Date 01.01.2001

Time zone -5 ET

Alarm time 12:00 am

Relative air pressure 29.91 inHg

Weather-picture threshold 0.09 inHg

LCD contrast level 5 (1-8 levels)

Rainfall per impulse 0.0204 inches

Storm alarm 0.09 inHg

Relative air pressure

alarm 28.34 inHg

(low) 30.71 inHg

(high)

Indoor temperature alarm 50ºF (low) 86ºF (high)

Outdoor temperature

alarm 32ºF (low) 104ºF (high)

Rain Cover Wall Bracket

Main Unit

Otros manuales para WS-2310

Tabla de contenidos

Otros manuales de Estación meteorológica de La Crosse Technology

La Crosse Technology

La Crosse Technology The Weather Channel WS-8500TWC-IT Manual de usuario

La Crosse Technology

La Crosse Technology WS-3500 Manual de usuario

La Crosse Technology

La Crosse Technology WS-7220U-IT Manual de usuario

La Crosse Technology

La Crosse Technology 327-1414Wv2 Manual de operación y mantenimiento

La Crosse Technology

La Crosse Technology WS-9009-IT Manual del propietario

La Crosse Technology

La Crosse Technology WS-9117U Manual de usuario

La Crosse Technology

La Crosse Technology 308-179OR Manual de usuario

La Crosse Technology

La Crosse Technology WS-9760U-IT Manual de usuario

La Crosse Technology

La Crosse Technology 308-805 Guía de instalación

La Crosse Technology

La Crosse Technology S77925V2 Manual de usuario

La Crosse Technology

La Crosse Technology C87030 Manual de operación y mantenimiento

La Crosse Technology

La Crosse Technology WS9611 Manual de usuario

La Crosse Technology

La Crosse Technology WS-1516U-IT Manual de usuario

La Crosse Technology

La Crosse Technology 308-1417BL Manual de usuario

La Crosse Technology

La Crosse Technology WS-2315AL Manual de usuario

La Crosse Technology

La Crosse Technology WS-9210U Manual de usuario

La Crosse Technology

La Crosse Technology C85845V3 Manual de usuario

La Crosse Technology

La Crosse Technology WS-1516-IT Manual de usuario

La Crosse Technology

La Crosse Technology S84107V2 Manual de usuario

La Crosse Technology

La Crosse Technology WS-7213U Manual de usuario

La Crosse Technology

La Crosse Technology V22-WRTH Manual de usuario

La Crosse Technology

La Crosse Technology V21V3 Dimensiones

La Crosse Technology

La Crosse Technology WS-9625U-IT Manual de usuario

La Crosse Technology

La Crosse Technology WS-7013U Manual de usuario

Manuales populares de Estación meteorológica de otras marcas

Auriol

Auriol AHFL 433 A1 Manual de usuario

NexSens

NexSens G2-HYDROMET Manual de usuario

Hyundai

Hyundai WS 2202 Manual de usuario

IROX

IROX HBVR761 UV-X Manual de usuario

ADE

ADE WS 1711 Manual de usuario

Auriol

Auriol z29592 Manual de usuario

Auriol

Auriol 296289 Manual de usuario

Hyundai

Hyundai WS 2266 Manual de usuario

Ventus

Ventus W177 Manual de usuario

National Geographic

National Geographic VA Colour RC Manual de usuario

Renkforce

Renkforce 1208067 Manual de usuario

Levenhuk

Levenhuk Discovery Report WA40 Manual de usuario

Instant Transmission

Instant Transmission MA 10410 Manual de usuario

Lutron Electronics

Lutron Electronics PHB-318 Manual de usuario

WAREMA

WAREMA EWFS Weather station eco Manual de usuario

TFA

TFA 30.3013.IT Manual de usuario

Alecto

Alecto WS-1200 Manual de usuario

Oregon Scientific

Oregon Scientific RMR966PA Manual de usuario