Kystar U3 Manual de usuario
U3
Multi-picture splicing processor
Version: v3.1
Release date: February 2022
Manual
Beijing KYSTAR Technology Co.,LTD
Professional Ultra HD Video Display
Control system integrated solution and service provider
Multi-Image Splicing Processor User Manual
Statement
Thank you for using our company's products.
The copyright of this manual is owned by our company, Without any written permission from
our company, it is forbidden to copy, delivery, distribution or storage of content of this document
in any form..The company reserves the right of modifications and improvements of any product
function described in the document without prior notice.
This product may be accompanied by a related control software, which is only for your
usage, and the ownership of the software is owned by the company. You are allowed to copy the
software but only limited to your personal usage. If the software is to be applied to other purposes,
in particular commercial purposes, please contact our company. Our company reserves the right of
investigate and affix legal liabilities of any infringement act.
Please read the manual carefully before using. Any improper operation may cause damage to
the product. It is operated with electricity and sufficient attention should be attached. Our
company bears no responsibility for any property loss and personal injury incurred from any
improper operation failing to follow the instructions in the manual. If the provision herein
conflicts with local laws or regulations, the local laws or regulations shall prevail.
It means that you accept the statement above if you use the product. If not, please contact
with the seller and return the product following relevant procedures.
Certification Description
“CE” Certification
EN 55022：2010
EN 55024：2010
EN 61000-3-3：2013
EN 61000-3-3：2014
EN 0950-1：2006+A11：2009+A1：2010+A12：2011+A2:2013
“FCC” Certification
FCC Part 15
ANSI C63.4：2014
“ROHS” Certification
EPA 3050B：1996，EN1122:2001
EPA 3052：1996，EPA 3060A
EPA 7196，EPA 3540C，EPA 8270C
Version Information
Version: v3.1
Issue Date: February,2022
Multi-Image Splicing Processor User Manual
SAFETY PRECAUTIONS
For your safety, please read this section carefully.
Power
Power supply of the device for normal operation is 100-200V AC.
Please make sure that the product is operated within the voltage range.
High voltage
High voltage devices are contained.
Do not dismantle without professionals
The device is not equipped with repair parts which is aimed for
maintenance by customer himself, so do not open chassis and operate
by yourself which may lead to unrecoverable damage of the device. If
maintenance is required, please contact after-sales service personnel.
Ensure sound grounding
For your safety, please ensure that power cable is grounded soundly
Keep away from strong magnetic field, engine and transformer
For normal operation of the device, please keep it away from strong
magnetic field, enginer and transformer.
Guard against damp
Keep operational environment dry. If the equipment is inadvertently
dampened, do not power the device and use it after being dried.
Keep away from explosives
Do not use the product in combustible or explosive environment.
Prevent liquid or conductive fragments getting into the chassis
Liquid or metal fragments should be stopped from getting into the
chassis. If so, the device should be powered off immediately and
power supply can only be allowed after clearance of foreign bodies.
Multi-Image Splicing Processor User Manual
Table of Contents
1. Product Introduction................................................................................ 1
2. Hardware Introduction.............................................................................2
2.1 Front Pane........................................................................................2
2.2 Back Panel....................................................................................... 3
3. Device Debugging................................................................................... 4
3.1 Device Connection.......................................................................... 4
3.2 Debugging Procedure...................................................................... 5
3.3 Case explanation..............................................................................8
3.4 Function Key................................................................................. 15
3.5 Advanced Menu.............................................................................20
4.Technical Parameters.............................................................................. 21
5. FQAs...................................................................................................... 22
Appendix: Graphics copy mode and extended mode setting....................24
1. AMD Video Card.............................................................................24
2. NVIDIA Video Card........................................................................24
Multi-Image Splicing Processor
1
1. Product Introduction
The multi-image splicing processor is a high-end video processing equipment
developed and manufactured by our company for LED large screen display,
performance and leasing, conference room, studio and so on.
The product adopts CPT+ FST splicing technology targeted for small pixel LED
display to guarantee uniformity and synchronization of splicing. The Super
Resolution Zoom-in Technology can help eliminate jaggies and reduce the fuzzy
sense and out-of-focus phenomenon due to image magnification.
The product enjoys the following features:
1. Support various signal input includes conventional DVI, VGA, HDMI, CVBS
and SDI ; support 4K Ultra HD input and realize large screen point-to-point display.
2. Support the output of 2 million 600 thousand pixel custom in copy mode,in
splicing mode the maximum level of 3840 pixels, the vertical maximum 1920 pixel
output.
3. Support free-form three-image layout and realize central control of main
screen, side screen, floor tile or canopy of the stage in an easy way.
4. Support signal echoing and view real-time input and output signals by
software.
5. Support multi-image preview and output monitoring.
6. Support signal and mode seamless switch, provide more than ten kinds of
transitional special effects
7. Support multi - group editable global graphics and text superposition.
8. Support luma matting, image transparency adjustment and edge feathering.
9. Support warm backup of multi-level input signal.
10. Support multi-machine synchronous cascade output.
Multi-Image Splicing Processor
2
2. Hardware Introduction
2.1 Front Pane
① ② ③ ④ ⑤ ⑥ ⑦ ⑧
⑨ ⑩ ⑪ ⑫ ⑬
1POWER: AC 220V POWER switch; ON indicates that the power supply is ON, and
OFF indicates that the power supply is OFF.
2LCD color screen: information display; Displays device and debugging information.
3ADJUST: ADJUST knob; You can select the information in the color screen through the
knob and quickly adjust various parameters, inverseClockwise to decrease, clockwise to increase,
press OK.
4OK: Confirm button to confirm debugging information.
5MENU: MENU button, you can enter the main MENU interface for device debugging.
6INFO: information query button; Example Query the real-time status of input signals.
7WIN: Screen information button; Display screen signal source and switch screen signal
source.
8S1-S6: Signal source button; The input source behind the device is under the main menu
screen, and the parameter input screen is a number1-5 and the back key.
9: Return or cancel the button.
10 : navigation buttons; Click to enter the navigation mode.
11 FUNC: Common function buttons; Click to enter the interface of common functions.
12 OUT: output selection key; The output can be black screen, blue screen, or Normal.
Multi-Image Splicing Processor
3
13 M1-M6: Shortcut mode call button; The shortcut mode button is displayed on the main
menu interface, and the parameter input interface is displayed belowThe numbers 6-0 and the
clear key.
2.2 Back Panel
① ② ③ ④ ⑤
⑥ ⑦ ⑧ ⑨ ⑩
1CARD：Send card slot; The sending card can be put into the processor for power supply.
2MONTOR ：Pre-monitoring channel; Used to monitor input signal source or output
output display content.
3OUTPUT ：Programming output channel; Pure digital DVI-D output, connected with
sending card, etc.
4LAN1:100m network control port; It can debug the equipment through software when it
is connected to the computer's 100 mbit/s network port.
5AC 100-220V: power interface; It can be connected to ac power supply of 100-220V.
6INPUT S5, S6: extended INPUT; Expandable with two conventional inputs or one
4KHDMI input.
7INPUT S1-S4: conventional INPUT; Input interface includes one set of DVI, one set of
HDMI, two sets of VGA and CVBS.
8LOOP: DVI LOOP exit; Loop out S1-DVI signal, which can be used for multi-machine
cascade.
9LAN2: GIGABit network control port; You can debug the device and implement the
echo function.
10 COM: RS232 control interface; Connect with the serial port of the computer, debug the
Multi-Image Splicing Processor
4
equipment through the upper computer software.
3. Device Debugging
3.1 Device Connection
Device connection could be divided into three parts: power connection, signal
connection and control connection (used for software debugging).
Power connection: device power supply. Connection method: connect power
cord to power plug.
Signal connection: the method transferring signal from signal source to LED
large screen. Connection method:
signal source→(e.g.: computer)Splicing Processor→Sending card→Large
screen.
Control connection: connect computer with device control port and debug device
connection method. There are three connection methods:
（1）Connect 100 mbit network control port with splicer LAN1 port, which can
set device software.
（2）Connect computer gigabit network port with splicer LAN2 port, which can
not only set device but also echo signal source image.
（3）Connect one crystal head of serial port line which is randomly donated by
device with splicer COM port, and plug DB9 into computer serial port. Any of the
three methods realizes device software control.
Connection diagram is as follows:
Signal Source
Monitor Scope
Display Screen
Computer (Connection Selectable)
Splicing Processor
Sending Card
(Connection Selectable)
Multi-Image Splicing Processor
5
Note:
All output displays
are the same.
Turn knob to select output
Click “OK” to adjust
Vertical Size:
1080
Vertical
Mosaic
Horizontal Size:
1920
OUT
Horizontal
Mosaic
Copy Output
Confirm
Select by finger key
Cancel
×1
×10
×100
OUT1
OUT2
Screen Parameters
3.2 Debugging Procedure
Step 1: Click “MENU” to enter into main menu interface and click “Device
Mode” to select splicing mode: copy mode, horizontal mosaic, and vertical mosaic.
Note: Copy Mode: all output contents are consistent; horizontal mosaic: contents
of all outputs are arranged horizontally; vertical mosaic: contents of all outputs are
arranged vertically;
Step 2: select suitable splicing mode and click “OK”; get back to main menu
interface to select “Screen parameter” and enter into its setting interface. Set loaded
screen point of each output interface and click “Confirm” after inputting, and then
screen splice is finished.
Note: there are two ways for number input:
(1)Adjust by rotate knob. Step length can be adjusted by “×1”“×10”“×100”, for
instance, “×100”means that number of rotate knob increases by 100 each time.
Device Mode
Multi-Image Splicing Processor
6
Image Layout
Image 1
S1
Layout 1
Layout 2
Layout 3
×1
×10
×100
Image Parameters
Select by finger key
Horizontal
Position: 0
Horizontal Size:
1920
Vertical
Position: 0
Vertical Size:
1080
Turn knob to select image
Click “OK”to adjust
Image 2
Image 3
Image 1
(2) Input by number of the front panel. For example, of the key refers to
figure 1.
Step 3: get back to main menu interface to select “Image layout” and enter into
image number selecting interface to select image number required to be set.
Note: In case of signal image, skip this step. For multi-image, it’s OK if image
number and item requirements are in consistent. Following operations can be taken
when layouts are not consistent.
Step 4: Click “OK” and return to main menu interface; select “Image parameter”
and enter into its setting interface to set size and position of each image.
Step 5: Click “Menu” and return to main menu interface; select “Clipped view”
to enter into its setting interface to set size and position of each image.
S1
Tabla de contenidos
Otros manuales de Hardware de computadora de Kystar
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
