Kystar KS9000 Manual de usuario
Multi-picture stitching processor
KS9000
user's manual
Beijing Kystar Technology Co., Ltd.
Safety Precautions
Danger
● There is high voltage in the equipment. Non-professional maintenance
personnel must not open the back cover to avoid danger.
Warning
● This equipment is not waterproof, please do waterproof treatment in
humid environment;
● The device must not be near fire or high temperature environment;
● If this device emits strange noise, smoke or strange smell, you should
immediately unplug the power plug and contact your dealer;
●It is strictly forbidden to plug and unplug VGA and DVI signal cables
while power is on.
Attention
1. Please read this manual carefully before use, and keep it for future use;
2. In the case of lightning or long-term use, please unplug the power plug;
3. This equipment is not suitable for non-professional operation and
debugging, please use it under the guidance of professionals;
4. Do not insert any objects into the ventilation holes of this equipment, so
as not to cause equipment damage or accidents;
5. It should not be used near water or other humid places;
6. It is not advisable to place the device in a heat sink or other high
temperature places;
7. please properly organize and place the power cord to prevent damage;
8. If the following conditions exist, unplug the power plug of the device and
entrust repair:
● When liquid has been spilled into the device
● When the device is dropped or the case is damaged
● When the device appears to be malfunctioning or performance is
significantly degrade
Directory
1、Introduction..............................................................................................................2
2、Hardware introduction.............................................................................................3
1. Introduction of the rear panel..............................................................................3
2. Connection diagram............................................................................................4
3、Software installation ................................................................................................5
4、Device connection....................................................................................................6
1.Open the Software ..............................................................................................6
5、Software settings....................................................................................................10
1.Output settings...................................................................................................10
2.Establishment of paintings.................................................................................12
3.Mode saving and recall......................................................................................13
6、Special function .....................................................................................................16
1.Insert picture ......................................................................................................16
2.Insert text ...........................................................................................................17
3.Adjusting the OSD.............................................................................................18
7、VGA Correction.....................................................................................................19
8、Selection of CV signals,character overlay for signals ...........................................20
9、Frequently asked questions....................................................................................22
Attachment：Settings for graphics card copy mode and extended mode...................24
1、AMD graphics card(XP system).....................................................................24
2、NVIDA graphics card(XP system）...............................................................25
3、Win7、Win8 system.......................................................................................26
KS9000 user manual www.kystar.com.cn
2
1.Introduction
This product is the industry's first truly multi-window splicer. It is a professional
video processing and control device. It is a splicing controller specially designed for
large-screen, projection, LCD and other devices.
The multi-screen mosaic processor developed by our company adopts FPGA pure
hardware architecture without any operating system. The entire system runs
completely closed, with simple operation and high stability.
Widely used in monitoring, dispatching command center, video conference center, etc.
This software is management software designed for this platform. Users can set
parameters and operate management of hardware devices through this software. All
operation procedures are intuitive and convenient.
Suitable for Windows XP, Windows7, Windows8, Windows10 operating
systems.
The following descriptions are all examples under the Window7 operating
system.
KS9000 user manual www.kystar.com.cn
3
2.Hardware introduction
1. Introduction of the rear panel
1. Input board: It can support DVI, VGA, CVBS, HDMI, SDI, IP stream, 4K and
other signal inputs, and can expand up to 216 channels.
2. I / O board: full DVI-I output, supports up to 30 splicing outputs.
3. control board: including power switch, COM port, network port, USB.
4. Power supply: up to four redundant power supplies.
2.Connection diagram
③
②
①
④
KS9000 user manual www.kystar.com.cn
4
3.Software Installation
KS9000 user manual www.kystar.com.cn
5
Insert the CD-ROM included in the product's junction box into the CD-ROM
drive. You can view the contents of the CD-ROM in the file manager.
Double-click to enter the following installation interface:
After selecting the installation language, click OK to enter the installation wizard
interface, as shown below:
Follow the wizard prompts to install until the installation wizard is complete and
the software installation is complete.
4.Device connection
KS9000 user manual www.kystar.com.cn
6
1.open the software
Double-click the software shortcut on the desktop to open the software and enter
the software startup page, as shown in the figure below:
Just click OK without password for the first time. If you set a password, you need to
enter the password correctly to enter the software.
Click "OK" to enter the software main interface, as shown below:
KS9000 user manual www.kystar.com.cn
7
Click "Connect Device", the "Communication Settings" window pops up, as shown in
the figure below:
This software can choose NET or COM two connection methods, choose different
connection methods to prepare different work.
(1) Select NET connection
I. Wiring
Use a CAT5 network cable, with one end connected to the processor's LAN port
and one end connected to the PC's network port (can also be connected through a
switch).
II. Modify the IP of the local connection
Under Windows 7 system, you can find the local connection through Start →
Control Panel → View Network Tasks → Change adapter settings. Right-click the
local connection and select Properties to bring up the dialog box below. Double-click
Internet Protocol Version 4 (TCP / IPv4), and The data is modified as shown below:
Otros manuales para KS9000
1
Tabla de contenidos
Otros manuales de Hardware de computadora de Kystar
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
