Kutai electronics EA440 Manual de usuario

KUTAI ELECTRONICS INDUSTRY CO., LTD.

TEL : +886-7-8121771 FAX : +886-7-8121775 Website : www.kutai.com.tw

Headquarters : No.3, Ln. 201, Qianfu St., Qianzhen Dist., Kaohsiung City 80664, Taiwan

EA440

Generator Automatic Voltage Regulator

Operation Manual

Self ExcitedAutomatic Voltage Regulator

Compatible with Newage SX440*

* All manufacturer names and numbers are used for reference purpose only

and do not imply that any part is the product of these manufacturer.

___________________________________________________________________________________________

2EA440

SECTION 1 : SPECIFICATION

Sensing Input

Quadrature Droop Input

Voltage 190 –264 Vac, 1 phase 2 wire

Burden 10 ohms

Frequency 50 / 60 Hz, selectable

Max. input 0.33 A

Max. sensitivity 0.07 A for 5% droop (PF=0)

Excitation Output

Voltage Max. 90 Vdc @ power input 207 Vac

Analogue Voltage Input

Current Continuous 4A

Input Resistance 1K ohm

Intermittent 10A for 10 secs.

Max. Input +/- 5 Vdc

Resistance Min. 15 ohm

Sensitivity 1V for 5% generator volts

External Voltage Adjustment

Under Frequency Protection

Max. +/- 8% @ 1K ohm 1 watt potentiometer

Set point 95% Hz

Slope 170% down to 30 Hz

Voltage Regulation

Less than +/- 1% ( with 4% engine governing )

Voltage Thermal Drift

Less than 3% at temperature range -40 to +70 ˚C

Build Up Voltage

5 Vac residual volts at power input terminal

Environment

Operating Temperature -40 to +70 ˚C

Soft Start Ramp Time

Storage Temperature -40 to +85 ˚C

2 seconds +/- 10%

Relative Humidity Max. 95%

Vibration 3.3 Gs @ 100 2K Hz

Static Power Dissipation

Max.12 watts

Dimensions

150.0 (L) x 135.0 (W) x 48.0 (H) mm

Weight

418 g +/- 2%

115.0

135.0

130.0

150.0

21.5

48.0

5.5

STABILITY

DROOP

TRIM

VOLT

UFRO

LED C B A

C-A < 90KW

C-B < 90-550KW

B-A < 550KW

Resistor

ATTENTION

1. AVR can be mounted directly on the

engine, genset, switchgear, control

panel, or any position that will not affect

operation. For dimension reference,

please see Figure 1.

2. All voltage readings are to be taken with

an average-reading voltmeter Meggers

and high-potential test equipment must

not be used. Use of such equipment

could damage the AVR.

3. Improper setting of under-frequency

protection could cause the output

voltage of the unit to drop or become

unstable under with changes in load.

Avoid making any changes to the U/F

setting unless necessary.

Figure 1 Outline Drawing

___________________________________________________________________________________________

EA440 3

SECTION 2 : WIRING

2.1 K1, K2 : Field input external switch terminals.

Linked for normal operation.

2.2 P2, P3 : External power input terminals.

2.3 3, 2 : Sensing input terminals.

2.4 1, 2 : External VR terminals. Linked for useless.

2.5 X,XX : X connect to field (+), XX connect to field

(-).

2.6 S1, S2 : Droop CT input terminal.

2.7 A1, A2 : VAR/PF controller input.

2.8 A, B, C : Link A, C for under 90 KW.

Link B, C for 90 550 KW.

Link A, B for over 550 KW.

2.9 J1 J8 : Jump select terminals, 2-3, 4-5, 6-7.

please refer to Figure 2 and Figure 3.

SECTION 3 : ADJUSTMENT

3.1 Voltage Adjustment

The generator output voltage can be altered by

adjustment of the volt VR on the AVR board, or by the

external trimmer (1K ohm) if fitted.

(1) The terminals 1&2 must be linked if no hand

trimmer.

(2) Before start the generator, please turn the Volt

trimmer on the AVR board fully anticlockwise Turn

the external trimmer to midway position.

(3) Turn the stability trimmer on the AVR board to

midway position.

(4) Connect a voltmeter to generator output voltage

terminals.

(5) Start generator set and run on no load at nominal

frequency 50 53 Hz or 60 63 Hz.

(6) If the red Led is illuminated, refer to the under

frequency roll off adjustment.

(7) Carefully turn volt trimmer clockwise until rated

voltage is reached.

3.2 Stability Adjustment

If a replacement AVR has been fitted or re-setting of

the stability control is required, turn the stability trimmer

slowly clockwise until the output voltage is steady, on

or off load.

3.3 Droop Adjustment

Generator intended for parallel are fitted with a

quadrature droop CT with provides a power factor

dependent signal for the AVR. The CT is connected to

S1, S2 on the AVR. The Droop adjustment is normally

present in the works to give 5% voltage droop at full

load zero power factor. Clockwise increases the

amount of CT signal injected into the AVR and

increases the droop with lagging power factor. With the

control fully anticlockwise there is no droop.

Figure 2 Bypass Drawing

Figure 3 Wiring Drawing

___________________________________________________________________________________________

4EA440

Figure 4 Manual Field Flash

3.4 Trim Adjustment

An auxiliary input is provided to connect to A1, A2. It is

designed to accept DC +/- 5V.Turn the TRIM trimmer

fully anticlockwise has no effect, Clockwise it has

maximum effect.

SECTION 4 : FIELD FLASHING

When the regulator is installed correctly but the

generator is failed to generate power. Besides carbon

brushes were worn out, here are two possible causes

below.

4.1 The polarity of field is inverse

Solution：Exchange the connection of F+ and F-.

4.2 The residual voltage is less than 5 Vac,

Solution 1：

4.2.1 Shut down generator, disconnect the wiring

between AVR and generator then flash the field.

Flashing duration = 3 seconds. (See wiring in

Figure 4)

Resistor 3 –5 ohms for full wave AVR

Resistor 5 –10 ohms for half wave AVR

Warning!! Over field flashing may damage

the field winding of generator.

4.2.2 Restart generator and measure the residual

voltage by AC Voltmeter, if it is still less than 5

Vac, repeat the previous process, after several

times, the residual voltage still cannot be built,

Kutai EB500 is strongly recommended, see

Figure 4.

Field

SWR

F+F-

BATT.

WARNING

Overly field flashing may damage the AVR or

generator excitation winding.

Please make sure you have read and understand

the contents of the instruction manual prior to

installation. Incorrect wiring connection may

result in irreversible damage to the product and

other equipments.

SECTION 5 : PARALLEL FUNCTION

5.1 Parallel Compensation

5.1.1 When it is required to operate the regulator in

parallel with an isolated or utility bus, in addition

to the regulator provisions, a 10VA current

transformer (CT) is required ( See Figure 3 ). The

CT is connected in a generator line and should

deliver from 1 amperes secondary current at

rated load.

5.1.2 The phase relationship of CT signal to the

regulator sensing voltage must be correct or the

system will not parallel properly. The CT must be

installed in the line of the three phase generator

that does not supply sensing to the regulator.

5.2 Reactive Droop Compensation

5.2.1 For reactive droop compensation, connect the

CT to it’s respective regulator as shown on

Figures 3.

5.2.2 A unit-parallel switch shorts the parallel CT

secondary to prevent any droop signal from

being injected into the regulating system during

single unit operation. The switch may not be

required on parallel droop compensation

applications where a voltage drop is not

objectionable.

___________________________________________________________________________________________

EA440 5

SECTION 6 : TROUBLE SHOOTING

SYMPTOM

POSSIBLE CAUSES

SOLUTIONS

Voltage does not

build up

Engine speed is too low

Please refer to the Generator Manual

wires are not connected well

Please refer to Figure 2

Defective Generator

Please refer to the Generator Manual

Low output voltage

External VR broken

Check wiring and testing VR

Terminal 1&2 not linked

Please linked terminal 1&2

Terminal 3&2 no sensing input

Please refer to Figure 2

Under frequency

Please refer to the Generator Manual

Defective Generator

Please refer to the Generator Manual

Over output voltage

AVR adjustment not well

Please refer to voltage adjustment page

Defective Generator

Please refer to the Generator Manual

※Appearance and specifications of products are subject to change for improvement without prior notice.

Tabla de contenidos

Otros manuales de Controladores de Kutai electronics

Kutai electronics

Kutai electronics EG3002F Manual de usuario

Kutai electronics

Kutai electronics ADVR-16-400HZ Manual de usuario

Kutai electronics

Kutai electronics EA05A Manual de usuario

Kutai electronics

Kutai electronics ADVR-073 Manual de usuario

Kutai electronics

Kutai electronics EG3002 Manual de usuario

Kutai electronics

Kutai electronics ADVR-2300M Manual de usuario

Kutai electronics

Kutai electronics EA06 Manual de usuario

Kutai electronics

Kutai electronics EA341 Manual de usuario

Kutai electronics

Kutai electronics EA125-8 Manual de usuario

Kutai electronics

Kutai electronics ADVR-2200M Manual de usuario

Kutai electronics

Kutai electronics EA63-2.5 Manual de usuario

Kutai electronics

Kutai electronics ADVR-083 Manual de usuario

Kutai electronics

Kutai electronics EA350 Manual de usuario

Kutai electronics

Kutai electronics EA200A Manual de usuario

Kutai electronics

Kutai electronics EA321 Manual de usuario

Kutai electronics

Kutai electronics EA230 Manual de usuario

Kutai electronics

Kutai electronics EB-9V Manual de usuario

Kutai electronics

Kutai electronics ADVR-12 Manual de usuario

Kutai electronics

Kutai electronics ADVR-083-400HZ Manual de usuario

Kutai electronics

Kutai electronics ATS-34 Ver1.0 Manual de usuario

Kutai electronics

Kutai electronics EA42-7 Manual de usuario

Kutai electronics

Kutai electronics ADVR-250 Manual de usuario

Kutai electronics

Kutai electronics ADVR-16 Manual de usuario

Kutai electronics

Kutai electronics ADVR-053 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario